Search

Search Results

• 1. [Image] Geological and Geophysical Analysis of Coso Geothermal Exploration Hole No. 1 (CGEH-1), Coso Hot Springs KGRA, California

  	The Coso Geothermal Exploration Hole number one (CGEH-1) was drilled in the Coso Hot Springs KGRA, California, from September 2 to December 2, 1977. Chip samples were collected at ten foot intervals and ...
  	Citation × Citation Citation Abstract Copy Title: Geological and Geophysical Analysis of Coso Geothermal Exploration Hole No. 1 (CGEH-1), Coso Hot Springs KGRA, California Author: Galbraith, R.M. Year: 1978 The Coso Geothermal Exploration Hole number one (CGEH-1) was drilled in the Coso Hot Springs KGRA, California, from September 2 to December 2, 1977. Chip samples were collected at ten foot intervals and extensive geophysical logging surveys were conducted to document the geologic character of the geothermal system as penetrated by CGEH-1. The major rock units encountered include a mafic metamorphic sequence and a leucogranite which intruded the metamorphic rocks. Only weak hydrothermal alteration was noted in these rocks. Drillhole surveys and drilling rate data indicate that the geothermal system is structurally controlled and that the drillhole itself was strongly influenced by structural zones. Water chemistry indicates that this geothermal resource is a hot-water rather than a vapor-dominated system. Several geophysical logs were employed to characterize the drillhole geology. The natural gamma and neutron porosity logs indicate gross rock type and the acoustics logs indicate fractured rock and potentially permeable zones. A series of temperature logs run as a function of time during and after the completion of drilling were most useful in delineating the zones of maximum heat flux. Convective heat flow and temperatures greater than 350/sup 0/F appear to occur only along an open fracture system encountered between depths of 1850 and 2775 feet. Temperature logs indicate a negative thermal gradient below 3000 feet Title: Geological and Geophysical Analysis of Coso Geothermal Exploration Hole No. 1 (CGEH-1), Coso Hot Springs KGRA, California Author: Galbraith, R.M. Year: 1978 The Coso Geothermal Exploration Hole number one (CGEH-1) was drilled in the Coso Hot Springs KGRA, California, from September 2 to December 2, 1977. Chip samples were collected at ten foot intervals and extensive geophysical logging surveys were conducted to document the geologic character of the geothermal system as penetrated by CGEH-1. The major rock units encountered include a mafic metamorphic sequence and a leucogranite which intruded the metamorphic rocks. Only weak hydrothermal alteration was noted in these rocks. Drillhole surveys and drilling rate data indicate that the geothermal system is structurally controlled and that the drillhole itself was strongly influenced by structural zones. Water chemistry indicates that this geothermal resource is a hot-water rather than a vapor-dominated system. Several geophysical logs were employed to characterize the drillhole geology. The natural gamma and neutron porosity logs indicate gross rock type and the acoustics logs indicate fractured rock and potentially permeable zones. A series of temperature logs run as a function of time during and after the completion of drilling were most useful in delineating the zones of maximum heat flux. Convective heat flow and temperatures greater than 350/sup 0/F appear to occur only along an open fracture system encountered between depths of 1850 and 2775 feet. Temperature logs indicate a negative thermal gradient below 3000 feet Close

• 2. [Image] Geothermal investigations at selected thermal systems of the northern Wasatch Front Weber and Box Elder Counties, Utah. Report of investigation No. 141

  	Numerous thermal springs are present along the Wasatch Front from Utah valley on the south to the state line on the north. These systems are just west of the Wasatch Mountains at the eastern edge of the ...
  	Citation × Citation Citation Abstract Copy Title: Geothermal investigations at selected thermal systems of the northern Wasatch Front Weber and Box Elder Counties, Utah. Report of investigation No. 141 Author: Murphy, P. Year: 1979 Numerous thermal springs are present along the Wasatch Front from Utah valley on the south to the state line on the north. These systems are just west of the Wasatch Mountains at the eastern edge of the Basin and Range physiographic province and within the active seismic zone referred to as the Intermountain Seismic Belt. This Report of Investigation is a summary of UGMS investigations at four northern Wasatch Front geothermal systems: Utah, Crystal (Madsen), and Udy hot springs; and the Little Mountain - south system. All of these resources are deep circulation systems and the water is heated by the normal heat flow of the Basin and Range Province. Heat from volcanic sources is not believed to contribute to the warming of any northern Wasatch Front springs. Data collected under the DOE/DGE state coupled program are presented for use by individuals interested in these systems; DOE/ET/28393-18 Title: Geothermal investigations at selected thermal systems of the northern Wasatch Front Weber and Box Elder Counties, Utah. Report of investigation No. 141 Author: Murphy, P. Year: 1979 Numerous thermal springs are present along the Wasatch Front from Utah valley on the south to the state line on the north. These systems are just west of the Wasatch Mountains at the eastern edge of the Basin and Range physiographic province and within the active seismic zone referred to as the Intermountain Seismic Belt. This Report of Investigation is a summary of UGMS investigations at four northern Wasatch Front geothermal systems: Utah, Crystal (Madsen), and Udy hot springs; and the Little Mountain - south system. All of these resources are deep circulation systems and the water is heated by the normal heat flow of the Basin and Range Province. Heat from volcanic sources is not believed to contribute to the warming of any northern Wasatch Front springs. Data collected under the DOE/DGE state coupled program are presented for use by individuals interested in these systems; DOE/ET/28393-18 Close

• 3. [Image] Geological and Geophysical Analysis of Coso Geothermal Exploration Hole No. 1 (CGEH-1), Coso Hot Springs KGRA, California

  	The Coso Geothermal Exploration Hole number one (CGEH-1) was drilled in the Coso Hot Springs KGRA, California from September 2 to December 2, 1977. Chip samples were collected at ten foot intervals and ...
  	Citation × Citation Citation Abstract Copy Title: Geological and Geophysical Analysis of Coso Geothermal Exploration Hole No. 1 (CGEH-1), Coso Hot Springs KGRA, California Author: Galbraith, R.M. Year: 1978 The Coso Geothermal Exploration Hole number one (CGEH-1) was drilled in the Coso Hot Springs KGRA, California from September 2 to December 2, 1977. Chip samples were collected at ten foot intervals and extensive geophysical logging surveys were conducted to document the geologic character of the geothermal system as penetrated by CGEH-1. The major rock units encountered include a mafic metamorphic sequence and a leucogranite which intruded the metamorphic rocks. Only weak hydrothermal alteration was noted in these rocks. Drillhole surveys and drilling rate data indicate that the geothermal system is structurally controlled and that the drillhole itself was strongly influenced by structural zones. Water chemistry indicates that this geothermal resource is a hot-water rather than a vapor-dominated system. Several geophysical logs were employed to characterize the drillhole geology. The natural gamma and neutron porosity logs indicate gross rock type and the acoustic logs indicate fractured rock and potentially permeable zones. A series of temperature logs run as a function of time during and after the completion of Drilling were most Useful in delineating the zones of maximum heat flux. Convective heat flow and temperatures greater than 350/sup 0/F appear to occur only along an open fracture system encountered between depths of 1850 and 2775 feet. Temperature logs indicate a negative thermal gradient below 3000 feet Title: Geological and Geophysical Analysis of Coso Geothermal Exploration Hole No. 1 (CGEH-1), Coso Hot Springs KGRA, California Author: Galbraith, R.M. Year: 1978 The Coso Geothermal Exploration Hole number one (CGEH-1) was drilled in the Coso Hot Springs KGRA, California from September 2 to December 2, 1977. Chip samples were collected at ten foot intervals and extensive geophysical logging surveys were conducted to document the geologic character of the geothermal system as penetrated by CGEH-1. The major rock units encountered include a mafic metamorphic sequence and a leucogranite which intruded the metamorphic rocks. Only weak hydrothermal alteration was noted in these rocks. Drillhole surveys and drilling rate data indicate that the geothermal system is structurally controlled and that the drillhole itself was strongly influenced by structural zones. Water chemistry indicates that this geothermal resource is a hot-water rather than a vapor-dominated system. Several geophysical logs were employed to characterize the drillhole geology. The natural gamma and neutron porosity logs indicate gross rock type and the acoustic logs indicate fractured rock and potentially permeable zones. A series of temperature logs run as a function of time during and after the completion of Drilling were most Useful in delineating the zones of maximum heat flux. Convective heat flow and temperatures greater than 350/sup 0/F appear to occur only along an open fracture system encountered between depths of 1850 and 2775 feet. Temperature logs indicate a negative thermal gradient below 3000 feet Close

• 4. [Image] Site-Specific Analysis of Hybrid Geothermal / Fossil Power Plants Volume One: Roosevelt Hot Springs KGRA

  	The economics of a particular hybrid plant must be evaluated with respect to a specific site. This volume focuses on the Roosevelt Hot Springs KGRA. The temperature, pressure, and flow rate data given ...
  	Citation × Citation Citation Abstract Copy Title: Site-Specific Analysis of Hybrid Geothermal / Fossil Power Plants Volume One: Roosevelt Hot Springs KGRA Author: Burbank City Public Service Dept., CA (USA) Year: 1977 The economics of a particular hybrid plant must be evaluated with respect to a specific site. This volume focuses on the Roosevelt Hot Springs KGRA. The temperature, pressure, and flow rate data given suggests the site deserves serious consideration for a hybrid plant. Key siting considerations which must be addressed before an economic judgment can be attempted are presented as follows: the availability, quality, and cost of coal; the availability of water; and the availability of transmission. Seismological and climate factors are presented Title: Site-Specific Analysis of Hybrid Geothermal / Fossil Power Plants Volume One: Roosevelt Hot Springs KGRA Author: Burbank City Public Service Dept., CA (USA) Year: 1977 The economics of a particular hybrid plant must be evaluated with respect to a specific site. This volume focuses on the Roosevelt Hot Springs KGRA. The temperature, pressure, and flow rate data given suggests the site deserves serious consideration for a hybrid plant. Key siting considerations which must be addressed before an economic judgment can be attempted are presented as follows: the availability, quality, and cost of coal; the availability of water; and the availability of transmission. Seismological and climate factors are presented Close

• 5. [Image] Petrology of the Quaternary Volcanics of the Roosevelt KGRA, and Adjoining Area, Utah. Final Report, Volume 1

  	The Roosevelt KGRA (Known Geothermal Resource Area) located near Milford, Utah, is associated with a suite of quaternary silicic volcanics distributed for 15 km along the crest and western flank of the ...
  	Citation × Citation Citation Abstract Copy Title: Petrology of the Quaternary Volcanics of the Roosevelt KGRA, and Adjoining Area, Utah. Final Report, Volume 1 Author: Nash, W.P. Year: 1976 The Roosevelt KGRA (Known Geothermal Resource Area) located near Milford, Utah, is associated with a suite of quaternary silicic volcanics distributed for 15 km along the crest and western flank of the Mineral Mountains, a large tertiary granite batholith. The volcanics are high-silica rhyolites and occur as domes, flows and tuffs. Initial eruptions resulted in two flows of low viscosity, phenocryst-poor rhyolite. Later activity consisted of pyroclastic eruptions and the emplacement of at least 9 viscous domes. In addition to abundant glass the rhyolites contain alkali feldspar, plagioclase, biotite, iron-titanium oxides and small amounts of hornblende, allanite, apatite, zircon, sphene and topaz. Magmatic temperatures were about 700C and water fugacities ranged from 350 to 3450 bars. Based on water fugacity calculations it is concluded that there may have been one or more shallow magma chambers in the Mineral Range at depths of about 1.6 km. Title: Petrology of the Quaternary Volcanics of the Roosevelt KGRA, and Adjoining Area, Utah. Final Report, Volume 1 Author: Nash, W.P. Year: 1976 The Roosevelt KGRA (Known Geothermal Resource Area) located near Milford, Utah, is associated with a suite of quaternary silicic volcanics distributed for 15 km along the crest and western flank of the Mineral Mountains, a large tertiary granite batholith. The volcanics are high-silica rhyolites and occur as domes, flows and tuffs. Initial eruptions resulted in two flows of low viscosity, phenocryst-poor rhyolite. Later activity consisted of pyroclastic eruptions and the emplacement of at least 9 viscous domes. In addition to abundant glass the rhyolites contain alkali feldspar, plagioclase, biotite, iron-titanium oxides and small amounts of hornblende, allanite, apatite, zircon, sphene and topaz. Magmatic temperatures were about 700C and water fugacities ranged from 350 to 3450 bars. Based on water fugacity calculations it is concluded that there may have been one or more shallow magma chambers in the Mineral Range at depths of about 1.6 km. Close

• 6. [Image] Atlantic coastal plain geothermal test holes, New Jersey: Hole completion reports

  	A description of the Atlantic Coastal Plains Geothermal Drilling Program and data for the following Geothermal test holes drilled in New Jersey are summarized: Site No. 40, Fort Monmouth; Site No. 41, ...
  	Citation × Citation Citation Abstract Copy Title: Atlantic coastal plain geothermal test holes, New Jersey: Hole completion reports Author: Cobb, L.B. Year: 1979 A description of the Atlantic Coastal Plains Geothermal Drilling Program and data for the following Geothermal test holes drilled in New Jersey are summarized: Site No. 40, Fort Monmouth; Site No. 41, Sea Girt; Site No. 39-A, Forked River; Site No. 38, Atlantic City; and Site No. 36, Cape May; NVO-1558-1 Title: Atlantic coastal plain geothermal test holes, New Jersey: Hole completion reports Author: Cobb, L.B. Year: 1979 A description of the Atlantic Coastal Plains Geothermal Drilling Program and data for the following Geothermal test holes drilled in New Jersey are summarized: Site No. 40, Fort Monmouth; Site No. 41, Sea Girt; Site No. 39-A, Forked River; Site No. 38, Atlantic City; and Site No. 36, Cape May; NVO-1558-1 Close

• 7. [Image] Geothermal Reservoir Categorization and Stimulation Study

  	Analyses of the fraction of geothermal wells that are dry (dry-hole fraction) indicate that geothermal reservoirs can be fitted into four basic categories: (i) Quaternary to late Tertiary sediments (almost ...
  	Citation × Citation Citation Abstract Copy Title: Geothermal Reservoir Categorization and Stimulation Study Author: Overton, H.L. Year: 1977 Analyses of the fraction of geothermal wells that are dry (dry-hole fraction) indicate that geothermal reservoirs can be fitted into four basic categories: (i) Quaternary to late Tertiary sediments (almost no dry holes); (ii) Quaternary to late Tertiary extrusives (approximately 20 percent dry holes); (iii) Mesozoic or older metamorphic rocks (approximately 25-30 percent dry holes); and (iv) Precambrian or younger rocks (data limited to Roosevelt Springs where 33 percent of the wells were dry). Failure of geothermal wells to flow economically is due mainly to low-permeability formations in unfractured regions. Generally the permeability correlates inversely with the temperature-age product and directly with the original rock porosity and pore size. However, this correlation fails whenever high-stress fields provide vertical fracturing or faulting, and it is the high-stress/low-permeability category that is most amenable to artificial stimulation by hydraulic fracturing, propellant fracturing, or chemical explosive fracturing. Category (i) geothermal fields (e.g., Cerro Prieto, Mexico; Niland, CA; East Mesa, CA) are not recommended for artificial stimulation because these younger sediments almost always produce warm or hot water. Most geothermal fields fit into category (ii) (e.g., Wairakei, New Zealand; Matsukawa, Japan; Ahuachapan, El Salvador) and in the case of Mt. Home, ID, and Chandler, AZ, possess some potential for stimulation. The Geysers is a category (iii) field, and its highly stressed brittle rocks should make this site amenable to stimulation by explosive fracturing techniques. Roosevelt Springs, UT, Well 9-1 is in category (iv) and is a flow failure. It represents a prime candidate for stimulation by hydraulic fracturing because it has a measured temperature of 227/sup 0/C, is cased and available for experimentation, and is within 900 m of an excellent geothermal producing well Title: Geothermal Reservoir Categorization and Stimulation Study Author: Overton, H.L. Year: 1977 Analyses of the fraction of geothermal wells that are dry (dry-hole fraction) indicate that geothermal reservoirs can be fitted into four basic categories: (i) Quaternary to late Tertiary sediments (almost no dry holes); (ii) Quaternary to late Tertiary extrusives (approximately 20 percent dry holes); (iii) Mesozoic or older metamorphic rocks (approximately 25-30 percent dry holes); and (iv) Precambrian or younger rocks (data limited to Roosevelt Springs where 33 percent of the wells were dry). Failure of geothermal wells to flow economically is due mainly to low-permeability formations in unfractured regions. Generally the permeability correlates inversely with the temperature-age product and directly with the original rock porosity and pore size. However, this correlation fails whenever high-stress fields provide vertical fracturing or faulting, and it is the high-stress/low-permeability category that is most amenable to artificial stimulation by hydraulic fracturing, propellant fracturing, or chemical explosive fracturing. Category (i) geothermal fields (e.g., Cerro Prieto, Mexico; Niland, CA; East Mesa, CA) are not recommended for artificial stimulation because these younger sediments almost always produce warm or hot water. Most geothermal fields fit into category (ii) (e.g., Wairakei, New Zealand; Matsukawa, Japan; Ahuachapan, El Salvador) and in the case of Mt. Home, ID, and Chandler, AZ, possess some potential for stimulation. The Geysers is a category (iii) field, and its highly stressed brittle rocks should make this site amenable to stimulation by explosive fracturing techniques. Roosevelt Springs, UT, Well 9-1 is in category (iv) and is a flow failure. It represents a prime candidate for stimulation by hydraulic fracturing because it has a measured temperature of 227/sup 0/C, is cased and available for experimentation, and is within 900 m of an excellent geothermal producing well Close

• 8. [Image] Delineation of an electrical resistivity anomaly, Malpais area, Beowawe KGRA, Eureka and Lander Counties, Nevada

  	A simple numerical model of previously released bipole-dipole resistivity data shows the margin of the graben to be anomalously conductive below the Malpais. The conductive area has been delineated with ...
  	Citation × Citation Citation Abstract Copy Title: Delineation of an electrical resistivity anomaly, Malpais area, Beowawe KGRA, Eureka and Lander Counties, Nevada Author: Smith, C. Year: 1980 A simple numerical model of previously released bipole-dipole resistivity data shows the margin of the graben to be anomalously conductive below the Malpais. The conductive area has been delineated with data from a dipole-dipole resistivity survey run in April 1980 for this study. Detailed numerical models of these data define a 1250 m wide body with resistivities less than 20 ohm-m that appear to connect The Geysers and the graben boundary. The minimum depth to the conductor is interpreted to be 375 m; its depth extent is undetermined. The electrical data do not resolve whether the anomaly below the Malpais may be the product of a defunct hydrothermal system or the signature of an active system. If thermal gradient data detect an enhanced heat flow anomaly in the same area, the Malpais may be a viable geothermal exploration target within the Beowawe KGRA; DOE/ID/12079-7 Title: Delineation of an electrical resistivity anomaly, Malpais area, Beowawe KGRA, Eureka and Lander Counties, Nevada Author: Smith, C. Year: 1980 A simple numerical model of previously released bipole-dipole resistivity data shows the margin of the graben to be anomalously conductive below the Malpais. The conductive area has been delineated with data from a dipole-dipole resistivity survey run in April 1980 for this study. Detailed numerical models of these data define a 1250 m wide body with resistivities less than 20 ohm-m that appear to connect The Geysers and the graben boundary. The minimum depth to the conductor is interpreted to be 375 m; its depth extent is undetermined. The electrical data do not resolve whether the anomaly below the Malpais may be the product of a defunct hydrothermal system or the signature of an active system. If thermal gradient data detect an enhanced heat flow anomaly in the same area, the Malpais may be a viable geothermal exploration target within the Beowawe KGRA; DOE/ID/12079-7 Close

• 9. [Image] Initial Investigation of Soil Mercury Geochemistry as an Aid to Drill Site Selection in Geothermal Systems

  	A mercury-in-soil survey was conducted at the Roosevelt Hot Springs Known Geothermal Resource Area (KGRA), Utah, to evaluate mercury soil geochemistry as a method of selecting exploration well sites in ...
  	Citation × Citation Citation Abstract Copy Title: Initial Investigation of Soil Mercury Geochemistry as an Aid to Drill Site Selection in Geothermal Systems Author: Capuano, R.M. Year: 1978 A mercury-in-soil survey was conducted at the Roosevelt Hot Springs Known Geothermal Resource Area (KGRA), Utah, to evaluate mercury soil geochemistry as a method of selecting exploration well sites in a hot-water geothermal system. Samples of -80 mesh soil were collected at 30.5 m intervals along traverses crossing known structures, surficial geothermal alteration, and exploration well sites, and were analyzed using a Gold Film Mercury Detector. Strong mercury anomalies occur at locations along known structures in close proximity to subsurface thermal activity; examples include areas over hot spring deposits and near a shallow producing well. In contrast, background mercury concentrations are present in nearby locations with little or no indication of subsurface thermal activity, such as areas around deep marginal producing wells and dry wells, and areas lacking hot spring deposits. These results indicate that mercury geochemical surveys can be useful for identifying and mapping structures controlling fluid flow in geothermal systems and for delineating areas overlying near-surface thermal activity. Soil mercury geochemistry thus provides information which may aid in the cost-effective selection of exploratory well sites Title: Initial Investigation of Soil Mercury Geochemistry as an Aid to Drill Site Selection in Geothermal Systems Author: Capuano, R.M. Year: 1978 A mercury-in-soil survey was conducted at the Roosevelt Hot Springs Known Geothermal Resource Area (KGRA), Utah, to evaluate mercury soil geochemistry as a method of selecting exploration well sites in a hot-water geothermal system. Samples of -80 mesh soil were collected at 30.5 m intervals along traverses crossing known structures, surficial geothermal alteration, and exploration well sites, and were analyzed using a Gold Film Mercury Detector. Strong mercury anomalies occur at locations along known structures in close proximity to subsurface thermal activity; examples include areas over hot spring deposits and near a shallow producing well. In contrast, background mercury concentrations are present in nearby locations with little or no indication of subsurface thermal activity, such as areas around deep marginal producing wells and dry wells, and areas lacking hot spring deposits. These results indicate that mercury geochemical surveys can be useful for identifying and mapping structures controlling fluid flow in geothermal systems and for delineating areas overlying near-surface thermal activity. Soil mercury geochemistry thus provides information which may aid in the cost-effective selection of exploratory well sites Close