Search

Search Results

• 1. [Image] Geothermal Heating System for the Children's Museum of Utah

  	The results of a study to determine the engineering and economic feasibility of using the Wasatch Hot Spring resource for space heating of the Children's Library building are presented. The Wasatch Hot ...
  	Citation × Citation Citation Abstract Copy Title: Geothermal Heating System for the Children's Museum of Utah Author: Karlsson, T. Year: 1984 The results of a study to determine the engineering and economic feasibility of using the Wasatch Hot Spring resource for space heating of the Children's Library building are presented. The Wasatch Hot Spring with a reported flow of about 63 gpm (240 l/min) at an average temperature of 104/sup 0/F is not capable of furnishing the needed heat for the Children's Museum building. The underground paths along which the thermal waters flow to their outlets at the Warm Springs Fault are not presently known. It is possible if the thermal water ascends from the deep layers of the earth along the Warm Springs Fault that increased geothermal flow at a higher temperature can be produced by drilling into the fault. Assuming that sufficient geothermal fluid quantity is produced by drilling in the area, an analysis is made of a geothermal heating system for the building based on different fluid temperatures. It is assumed that the present and planned heating systems be left intact with the gas fired boilers taking over during cold periods when the geothermal system fails to provide sufficient heat. Economic analysis shows that the geothermal system is very attractive, even for the lowest geothermal fluid temperature considered (110/sup 0/F) Title: Geothermal Heating System for the Children's Museum of Utah Author: Karlsson, T. Year: 1984 The results of a study to determine the engineering and economic feasibility of using the Wasatch Hot Spring resource for space heating of the Children's Library building are presented. The Wasatch Hot Spring with a reported flow of about 63 gpm (240 l/min) at an average temperature of 104/sup 0/F is not capable of furnishing the needed heat for the Children's Museum building. The underground paths along which the thermal waters flow to their outlets at the Warm Springs Fault are not presently known. It is possible if the thermal water ascends from the deep layers of the earth along the Warm Springs Fault that increased geothermal flow at a higher temperature can be produced by drilling into the fault. Assuming that sufficient geothermal fluid quantity is produced by drilling in the area, an analysis is made of a geothermal heating system for the building based on different fluid temperatures. It is assumed that the present and planned heating systems be left intact with the gas fired boilers taking over during cold periods when the geothermal system fails to provide sufficient heat. Economic analysis shows that the geothermal system is very attractive, even for the lowest geothermal fluid temperature considered (110/sup 0/F) Close

• 2. [Image] Geological and Geophysical Analysis of Coso Geothermal Exploration Hole No. 1 (CGEH-1), Coso Hot Springs KGRA, California

  	The Coso Geothermal Exploration Hole number one (CGEH-1) was drilled in the Coso Hot Springs KGRA, California, from September 2 to December 2, 1977. Chip samples were collected at ten foot intervals and ...
  	Citation × Citation Citation Abstract Copy Title: Geological and Geophysical Analysis of Coso Geothermal Exploration Hole No. 1 (CGEH-1), Coso Hot Springs KGRA, California Author: Galbraith, R.M. Year: 1978 The Coso Geothermal Exploration Hole number one (CGEH-1) was drilled in the Coso Hot Springs KGRA, California, from September 2 to December 2, 1977. Chip samples were collected at ten foot intervals and extensive geophysical logging surveys were conducted to document the geologic character of the geothermal system as penetrated by CGEH-1. The major rock units encountered include a mafic metamorphic sequence and a leucogranite which intruded the metamorphic rocks. Only weak hydrothermal alteration was noted in these rocks. Drillhole surveys and drilling rate data indicate that the geothermal system is structurally controlled and that the drillhole itself was strongly influenced by structural zones. Water chemistry indicates that this geothermal resource is a hot-water rather than a vapor-dominated system. Several geophysical logs were employed to characterize the drillhole geology. The natural gamma and neutron porosity logs indicate gross rock type and the acoustics logs indicate fractured rock and potentially permeable zones. A series of temperature logs run as a function of time during and after the completion of drilling were most useful in delineating the zones of maximum heat flux. Convective heat flow and temperatures greater than 350/sup 0/F appear to occur only along an open fracture system encountered between depths of 1850 and 2775 feet. Temperature logs indicate a negative thermal gradient below 3000 feet Title: Geological and Geophysical Analysis of Coso Geothermal Exploration Hole No. 1 (CGEH-1), Coso Hot Springs KGRA, California Author: Galbraith, R.M. Year: 1978 The Coso Geothermal Exploration Hole number one (CGEH-1) was drilled in the Coso Hot Springs KGRA, California, from September 2 to December 2, 1977. Chip samples were collected at ten foot intervals and extensive geophysical logging surveys were conducted to document the geologic character of the geothermal system as penetrated by CGEH-1. The major rock units encountered include a mafic metamorphic sequence and a leucogranite which intruded the metamorphic rocks. Only weak hydrothermal alteration was noted in these rocks. Drillhole surveys and drilling rate data indicate that the geothermal system is structurally controlled and that the drillhole itself was strongly influenced by structural zones. Water chemistry indicates that this geothermal resource is a hot-water rather than a vapor-dominated system. Several geophysical logs were employed to characterize the drillhole geology. The natural gamma and neutron porosity logs indicate gross rock type and the acoustics logs indicate fractured rock and potentially permeable zones. A series of temperature logs run as a function of time during and after the completion of drilling were most useful in delineating the zones of maximum heat flux. Convective heat flow and temperatures greater than 350/sup 0/F appear to occur only along an open fracture system encountered between depths of 1850 and 2775 feet. Temperature logs indicate a negative thermal gradient below 3000 feet Close

• 3. [Image] Geothermal Investigations in Idaho. Part 8. Heat Flow Study of the Snake River Plain Region, Idaho

  	The Snake River Plain of Idaho has recent lava flows and a large number of thermal springs and wells. A heat flow study was initiated which, together with available geological and geophysical information, ...
  	Citation × Citation Citation Abstract Copy Title: Geothermal Investigations in Idaho. Part 8. Heat Flow Study of the Snake River Plain Region, Idaho Author: Brott, C.A. Year: 1976 The Snake River Plain of Idaho has recent lava flows and a large number of thermal springs and wells. A heat flow study was initiated which, together with available geological and geophysical information, allows a better definition of the geothermal resource and evaluation of the geothermal potential. Local geothermal anomalies were not the objects of this study and have not been studied in detail. The quality of the heat flow values obtained varies as interpretation was necessary to determine geothermal gradients for many of the holes which had disturbances. A major problem in determining the heat flow values is the lack of knowledge of the in situ porosity of the rocks. The heat flow values obtained for the Eastern Snake River Plain are from shallow wells (< 200 m), hence the heat flow there is low (< 0.5 HFU) because of the water movement in the Snake Plain aquifer. The anomalous regional heat flow pattern around the Snake River Plain, together with other geophysical and geological data, suggest the presence of a major crustal heat source. With the exception of the area of the Snake Plain aquifer, high geothermal gradients were found in all areas of southern Idaho (40 to 100/sup 0/C/km). Temperatures hot enough for space heating can be found most anywhere in the Plain at relatively shallow depths (1 to 2 km). Temperatures hot enough for electrical power generation (200/sup 0/C) can be found beneath southern Idaho almost anywhere at depths of 3 to 4 kilometers. The Plain is fault bounded and hot water circulating along the fault zones from depths can be a very important geothermal resource at shallow depths. The margins of the Plain have the highest heat flow values, are the most faulted, and have possibly the highest geothermal resource potential Title: Geothermal Investigations in Idaho. Part 8. Heat Flow Study of the Snake River Plain Region, Idaho Author: Brott, C.A. Year: 1976 The Snake River Plain of Idaho has recent lava flows and a large number of thermal springs and wells. A heat flow study was initiated which, together with available geological and geophysical information, allows a better definition of the geothermal resource and evaluation of the geothermal potential. Local geothermal anomalies were not the objects of this study and have not been studied in detail. The quality of the heat flow values obtained varies as interpretation was necessary to determine geothermal gradients for many of the holes which had disturbances. A major problem in determining the heat flow values is the lack of knowledge of the in situ porosity of the rocks. The heat flow values obtained for the Eastern Snake River Plain are from shallow wells (< 200 m), hence the heat flow there is low (< 0.5 HFU) because of the water movement in the Snake Plain aquifer. The anomalous regional heat flow pattern around the Snake River Plain, together with other geophysical and geological data, suggest the presence of a major crustal heat source. With the exception of the area of the Snake Plain aquifer, high geothermal gradients were found in all areas of southern Idaho (40 to 100/sup 0/C/km). Temperatures hot enough for space heating can be found most anywhere in the Plain at relatively shallow depths (1 to 2 km). Temperatures hot enough for electrical power generation (200/sup 0/C) can be found beneath southern Idaho almost anywhere at depths of 3 to 4 kilometers. The Plain is fault bounded and hot water circulating along the fault zones from depths can be a very important geothermal resource at shallow depths. The margins of the Plain have the highest heat flow values, are the most faulted, and have possibly the highest geothermal resource potential Close

• 4. [Image] Transient well testing in two-phase geothermal reservoirs

  	A study of well test analysis techniques in two-phase geothermal reservoirs has been conducted using a three-dimensional, two-phase, wellbore and reservoir simulation model. Well tests from Cerro Prieto ...
  	Citation × Citation Citation Abstract Copy Title: Transient well testing in two-phase geothermal reservoirs Author: Aydelotte, S.R. Year: 1980 A study of well test analysis techniques in two-phase geothermal reservoirs has been conducted using a three-dimensional, two-phase, wellbore and reservoir simulation model. Well tests from Cerro Prieto and the Hawaiian Geothermal project have been history matched. Using these well tests as a base, the influence of reservoir permeability, porosity, thickness, and heat capacity, along with flow rate and fracturing were studied. Single and two-phase transient well test equations were used to analyze these tests with poor results due to rapidly changing fluid properties and inability to calculate the flowing steam saturation in the reservoir. The injection of cold water into the reservoir does give good data from which formation properties can be calculated. Title: Transient well testing in two-phase geothermal reservoirs Author: Aydelotte, S.R. Year: 1980 A study of well test analysis techniques in two-phase geothermal reservoirs has been conducted using a three-dimensional, two-phase, wellbore and reservoir simulation model. Well tests from Cerro Prieto and the Hawaiian Geothermal project have been history matched. Using these well tests as a base, the influence of reservoir permeability, porosity, thickness, and heat capacity, along with flow rate and fracturing were studied. Single and two-phase transient well test equations were used to analyze these tests with poor results due to rapidly changing fluid properties and inability to calculate the flowing steam saturation in the reservoir. The injection of cold water into the reservoir does give good data from which formation properties can be calculated. Close

• 5. [Image] Geothermal Modeling of the Raft River Geothermal Field

  	The results to date of chemical modeling of the Raft River KGRA are presented. Earlier work indicated a northwest-southeast anomaly in the contours. Modeling techniques applied to more complete data allowed ...
  	Citation × Citation Citation Abstract Copy Title: Geothermal Modeling of the Raft River Geothermal Field Author: Overton, H.L. Year: 1979 The results to date of chemical modeling of the Raft River KGRA are presented. Earlier work indicated a northwest-southeast anomaly in the contours. Modeling techniques applied to more complete data allowed further definition of the anomaly. Models described in this report show the source of various minerals in the geothermal water. There appears to be a regional heat source that gives rise to uniform conductive heat flow in the region, but convective flow is concentrated near the upwelling in the Crook well vicinity. Recommendations are made concerning field expansion and additional work needed to refine the overall reservoir model; EGG-2004 Title: Geothermal Modeling of the Raft River Geothermal Field Author: Overton, H.L. Year: 1979 The results to date of chemical modeling of the Raft River KGRA are presented. Earlier work indicated a northwest-southeast anomaly in the contours. Modeling techniques applied to more complete data allowed further definition of the anomaly. Models described in this report show the source of various minerals in the geothermal water. There appears to be a regional heat source that gives rise to uniform conductive heat flow in the region, but convective flow is concentrated near the upwelling in the Crook well vicinity. Recommendations are made concerning field expansion and additional work needed to refine the overall reservoir model; EGG-2004 Close

• 6. [Image] Geothermal investigations at selected thermal systems of the northern Wasatch Front Weber and Box Elder Counties, Utah. Report of investigation No. 141

  	Numerous thermal springs are present along the Wasatch Front from Utah valley on the south to the state line on the north. These systems are just west of the Wasatch Mountains at the eastern edge of the ...
  	Citation × Citation Citation Abstract Copy Title: Geothermal investigations at selected thermal systems of the northern Wasatch Front Weber and Box Elder Counties, Utah. Report of investigation No. 141 Author: Murphy, P. Year: 1979 Numerous thermal springs are present along the Wasatch Front from Utah valley on the south to the state line on the north. These systems are just west of the Wasatch Mountains at the eastern edge of the Basin and Range physiographic province and within the active seismic zone referred to as the Intermountain Seismic Belt. This Report of Investigation is a summary of UGMS investigations at four northern Wasatch Front geothermal systems: Utah, Crystal (Madsen), and Udy hot springs; and the Little Mountain - south system. All of these resources are deep circulation systems and the water is heated by the normal heat flow of the Basin and Range Province. Heat from volcanic sources is not believed to contribute to the warming of any northern Wasatch Front springs. Data collected under the DOE/DGE state coupled program are presented for use by individuals interested in these systems; DOE/ET/28393-18 Title: Geothermal investigations at selected thermal systems of the northern Wasatch Front Weber and Box Elder Counties, Utah. Report of investigation No. 141 Author: Murphy, P. Year: 1979 Numerous thermal springs are present along the Wasatch Front from Utah valley on the south to the state line on the north. These systems are just west of the Wasatch Mountains at the eastern edge of the Basin and Range physiographic province and within the active seismic zone referred to as the Intermountain Seismic Belt. This Report of Investigation is a summary of UGMS investigations at four northern Wasatch Front geothermal systems: Utah, Crystal (Madsen), and Udy hot springs; and the Little Mountain - south system. All of these resources are deep circulation systems and the water is heated by the normal heat flow of the Basin and Range Province. Heat from volcanic sources is not believed to contribute to the warming of any northern Wasatch Front springs. Data collected under the DOE/DGE state coupled program are presented for use by individuals interested in these systems; DOE/ET/28393-18 Close

• 7. [Image] Geological and Geophysical Analysis of Coso Geothermal Exploration Hole No. 1 (CGEH-1), Coso Hot Springs KGRA, California

  	The Coso Geothermal Exploration Hole number one (CGEH-1) was drilled in the Coso Hot Springs KGRA, California from September 2 to December 2, 1977. Chip samples were collected at ten foot intervals and ...
  	Citation × Citation Citation Abstract Copy Title: Geological and Geophysical Analysis of Coso Geothermal Exploration Hole No. 1 (CGEH-1), Coso Hot Springs KGRA, California Author: Galbraith, R.M. Year: 1978 The Coso Geothermal Exploration Hole number one (CGEH-1) was drilled in the Coso Hot Springs KGRA, California from September 2 to December 2, 1977. Chip samples were collected at ten foot intervals and extensive geophysical logging surveys were conducted to document the geologic character of the geothermal system as penetrated by CGEH-1. The major rock units encountered include a mafic metamorphic sequence and a leucogranite which intruded the metamorphic rocks. Only weak hydrothermal alteration was noted in these rocks. Drillhole surveys and drilling rate data indicate that the geothermal system is structurally controlled and that the drillhole itself was strongly influenced by structural zones. Water chemistry indicates that this geothermal resource is a hot-water rather than a vapor-dominated system. Several geophysical logs were employed to characterize the drillhole geology. The natural gamma and neutron porosity logs indicate gross rock type and the acoustic logs indicate fractured rock and potentially permeable zones. A series of temperature logs run as a function of time during and after the completion of Drilling were most Useful in delineating the zones of maximum heat flux. Convective heat flow and temperatures greater than 350/sup 0/F appear to occur only along an open fracture system encountered between depths of 1850 and 2775 feet. Temperature logs indicate a negative thermal gradient below 3000 feet Title: Geological and Geophysical Analysis of Coso Geothermal Exploration Hole No. 1 (CGEH-1), Coso Hot Springs KGRA, California Author: Galbraith, R.M. Year: 1978 The Coso Geothermal Exploration Hole number one (CGEH-1) was drilled in the Coso Hot Springs KGRA, California from September 2 to December 2, 1977. Chip samples were collected at ten foot intervals and extensive geophysical logging surveys were conducted to document the geologic character of the geothermal system as penetrated by CGEH-1. The major rock units encountered include a mafic metamorphic sequence and a leucogranite which intruded the metamorphic rocks. Only weak hydrothermal alteration was noted in these rocks. Drillhole surveys and drilling rate data indicate that the geothermal system is structurally controlled and that the drillhole itself was strongly influenced by structural zones. Water chemistry indicates that this geothermal resource is a hot-water rather than a vapor-dominated system. Several geophysical logs were employed to characterize the drillhole geology. The natural gamma and neutron porosity logs indicate gross rock type and the acoustic logs indicate fractured rock and potentially permeable zones. A series of temperature logs run as a function of time during and after the completion of Drilling were most Useful in delineating the zones of maximum heat flux. Convective heat flow and temperatures greater than 350/sup 0/F appear to occur only along an open fracture system encountered between depths of 1850 and 2775 feet. Temperature logs indicate a negative thermal gradient below 3000 feet Close

• 8. [Image] Geothermal direct heat project, Marlin, Texas: Environmental assessment

  	The Federal action addressed is retrofitting a heating and hot water system in a hospital at Marlin, Texas, with a geothermal preheat system. The project will be located within the existing hospital boiler ...
  	Citation × Citation Citation Abstract Copy Title: Geothermal direct heat project, Marlin, Texas: Environmental assessment Year: 1979 The Federal action addressed is retrofitting a heating and hot water system in a hospital at Marlin, Texas, with a geothermal preheat system. The project will be located within the existing hospital boiler room. One supply well will be drilled in an existing adjacent parking lot. Fluid disposal from operation will depend on fluid properties and may be by surface disposal to existing street drains, by surface disposal to a new drainage system, or by injection into a new injection well, depending on total dissolved solids (TDS) content. Environmental impacts of construction are expected to be small because of the existing structures and paved areas. Construction run-off and geothermal flow-test fluid will pass through a small pond in the city park, lowering its water quality, at least temporarily. Construction noise is not expected to be out of character with existing noises around the hospital. Project operation is not expected to produce significant impacts because of the decision point to determine fluid composition prior to designating a disposal method. Injection would be into a saline aquifer, and surface discharge would not appreciably lower water quality in the Brazos River; DOE/EA-0067 Title: Geothermal direct heat project, Marlin, Texas: Environmental assessment Year: 1979 The Federal action addressed is retrofitting a heating and hot water system in a hospital at Marlin, Texas, with a geothermal preheat system. The project will be located within the existing hospital boiler room. One supply well will be drilled in an existing adjacent parking lot. Fluid disposal from operation will depend on fluid properties and may be by surface disposal to existing street drains, by surface disposal to a new drainage system, or by injection into a new injection well, depending on total dissolved solids (TDS) content. Environmental impacts of construction are expected to be small because of the existing structures and paved areas. Construction run-off and geothermal flow-test fluid will pass through a small pond in the city park, lowering its water quality, at least temporarily. Construction noise is not expected to be out of character with existing noises around the hospital. Project operation is not expected to produce significant impacts because of the decision point to determine fluid composition prior to designating a disposal method. Injection would be into a saline aquifer, and surface discharge would not appreciably lower water quality in the Brazos River; DOE/EA-0067 Close

• 9. [Image] DHE (Downhole Heat Exchangers)

  	The use of downhole heat exchangers (DHE) for residential or commercial space and domestic water heating and other applications has several desirable features. Systems are nearly or completely passive ...
  	Citation × Citation Citation Abstract Copy Title: DHE (Downhole Heat Exchangers) Author: Culver, G. Year: 1990 The use of downhole heat exchangers (DHE) for residential or commercial space and domestic water heating and other applications has several desirable features. Systems are nearly or completely passive -- that is, no or very little geothermal water or steam is produced from the well either reducing or completely eliminating surface environmental concerns and the need for disposal systems or injection wells. Initial cost of pumps and installation are eliminated or reduced along with pumping power costs and maintenance costs associated with pumping often corrosive geothermal fluids. Many residential and small commercial systems do not require circulating pumps because the density difference in the incoming and outgoing sides of the loop are sufficient to overcome circulating friction losses in the entire system. The major disadvantage of DHEs is their dependence on natural heat flow. In areas where geological conditions provide high permeability and a natural hydraulic gradient, DHEs can provide a substantial quantity of heat. A single 500-ft (152 m) well in Klamath Falls, Oregon, supplies over one megawatt thermal and output is apparently limited by the surface area of pipe that can be installed in the well bore. In contrast, DHEs used in conjunction with heat pumps may supply less than 8 KW from a well of similar depth. Here output is limited by conductive heat flow with perhaps a small contribution from convection near the well bore. The highest capacity DHE reported to date, in Turkey, supplies 6 MW thermal from an 820-ft (250 m) well. There were two main goals for this project. The first was to gather, disseminate and exchange internationally information on DHEs. The second was to perform experiments that would provide insight into well bore/aquifer interaction and thereby provide more information on which to base DHE designs. 27 refs., 31 figs., 3 tabs. Title: DHE (Downhole Heat Exchangers) Author: Culver, G. Year: 1990 The use of downhole heat exchangers (DHE) for residential or commercial space and domestic water heating and other applications has several desirable features. Systems are nearly or completely passive -- that is, no or very little geothermal water or steam is produced from the well either reducing or completely eliminating surface environmental concerns and the need for disposal systems or injection wells. Initial cost of pumps and installation are eliminated or reduced along with pumping power costs and maintenance costs associated with pumping often corrosive geothermal fluids. Many residential and small commercial systems do not require circulating pumps because the density difference in the incoming and outgoing sides of the loop are sufficient to overcome circulating friction losses in the entire system. The major disadvantage of DHEs is their dependence on natural heat flow. In areas where geological conditions provide high permeability and a natural hydraulic gradient, DHEs can provide a substantial quantity of heat. A single 500-ft (152 m) well in Klamath Falls, Oregon, supplies over one megawatt thermal and output is apparently limited by the surface area of pipe that can be installed in the well bore. In contrast, DHEs used in conjunction with heat pumps may supply less than 8 KW from a well of similar depth. Here output is limited by conductive heat flow with perhaps a small contribution from convection near the well bore. The highest capacity DHE reported to date, in Turkey, supplies 6 MW thermal from an 820-ft (250 m) well. There were two main goals for this project. The first was to gather, disseminate and exchange internationally information on DHEs. The second was to perform experiments that would provide insight into well bore/aquifer interaction and thereby provide more information on which to base DHE designs. 27 refs., 31 figs., 3 tabs. Close

• 10. [Image] Atlantic coastal plain geothermal test holes, New Jersey: Hole completion reports

  	A description of the Atlantic Coastal Plains Geothermal Drilling Program and data for the following Geothermal test holes drilled in New Jersey are summarized: Site No. 40, Fort Monmouth; Site No. 41, ...
  	Citation × Citation Citation Abstract Copy Title: Atlantic coastal plain geothermal test holes, New Jersey: Hole completion reports Author: Cobb, L.B. Year: 1979 A description of the Atlantic Coastal Plains Geothermal Drilling Program and data for the following Geothermal test holes drilled in New Jersey are summarized: Site No. 40, Fort Monmouth; Site No. 41, Sea Girt; Site No. 39-A, Forked River; Site No. 38, Atlantic City; and Site No. 36, Cape May; NVO-1558-1 Title: Atlantic coastal plain geothermal test holes, New Jersey: Hole completion reports Author: Cobb, L.B. Year: 1979 A description of the Atlantic Coastal Plains Geothermal Drilling Program and data for the following Geothermal test holes drilled in New Jersey are summarized: Site No. 40, Fort Monmouth; Site No. 41, Sea Girt; Site No. 39-A, Forked River; Site No. 38, Atlantic City; and Site No. 36, Cape May; NVO-1558-1 Close