Search

Search Results

• 1. [Image] Steady-State and Transient Wellbore Temperatures during Drilling

  	An extensive literature search was made to locate technical publications and computer programs relating to wellbore temperatures during drilling operations. The search confirmed the need for knowledge ...
  	Citation × Citation Citation Abstract Copy Title: Steady-State and Transient Wellbore Temperatures during Drilling Author: McDonald, W.J. Year: 1976 An extensive literature search was made to locate technical publications and computer programs relating to wellbore temperatures during drilling operations. The search confirmed the need for knowledge of transient and steady state circulating temperatures in the design of geothermal bits. Two approaches were used in calculating borehole temperatures. The steady state solution of Holmes and Swift was programmed and 2100 cases calculated for various borehole configurations. For transient temperature studies, calculations were made for ten borehole configurations. These calculations help emphasize the need for better high temperature bit performance and improved engineering procedures in drilling. The conclusions and recommendations are based on latest available technology for calculating wellbore temperatures Title: Steady-State and Transient Wellbore Temperatures during Drilling Author: McDonald, W.J. Year: 1976 An extensive literature search was made to locate technical publications and computer programs relating to wellbore temperatures during drilling operations. The search confirmed the need for knowledge of transient and steady state circulating temperatures in the design of geothermal bits. Two approaches were used in calculating borehole temperatures. The steady state solution of Holmes and Swift was programmed and 2100 cases calculated for various borehole configurations. For transient temperature studies, calculations were made for ten borehole configurations. These calculations help emphasize the need for better high temperature bit performance and improved engineering procedures in drilling. The conclusions and recommendations are based on latest available technology for calculating wellbore temperatures Close

• 2. [Image] Fluid-Temperature Logs for Selected Wells in Eastern Washington

  	This Open-File Report consists of fluid temperature logs compiled during studies of the geohydrology and low temperature geothermal resources of eastern Washington. The fluid temperature logs are divided ...
  	Citation × Citation Citation Abstract Copy Title: Fluid-Temperature Logs for Selected Wells in Eastern Washington Author: Stoffel, K. L. Year: 1983 This Open-File Report consists of fluid temperature logs compiled during studies of the geohydrology and low temperature geothermal resources of eastern Washington. The fluid temperature logs are divided into two groups. Part A consists of wells which are concentrated in the Moses Lake-Ritzville-Connell area. Full geophysical log suites for many of these wells are presented in Stoffel and Widness (1983) and discussed in Widness (1983, 1984). Part B consists of wells outside of the Moses Lake-Ritzville-Connell study area Title: Fluid-Temperature Logs for Selected Wells in Eastern Washington Author: Stoffel, K. L. Year: 1983 This Open-File Report consists of fluid temperature logs compiled during studies of the geohydrology and low temperature geothermal resources of eastern Washington. The fluid temperature logs are divided into two groups. Part A consists of wells which are concentrated in the Moses Lake-Ritzville-Connell area. Full geophysical log suites for many of these wells are presented in Stoffel and Widness (1983) and discussed in Widness (1983, 1984). Part B consists of wells outside of the Moses Lake-Ritzville-Connell study area Close

• 3. [Image] Neutron Formation Temperature Gauge and Neutron Activation Analysis Brine Flow Meter. Final Report, October 1, 1976--March 31, 1978

  	Feasibility studies of nuclear techniques applicable to the determination of geothermal formation temperature and two-phase brine flow downhole have been performed. The formation temperature gauging technique ...
  	Citation × Citation Citation Abstract Copy Title: Neutron Formation Temperature Gauge and Neutron Activation Analysis Brine Flow Meter. Final Report, October 1, 1976--March 31, 1978 Author: Vagelatos, N. Year: 1978 Feasibility studies of nuclear techniques applicable to the determination of geothermal formation temperature and two-phase brine flow downhole have been performed. The formation temperature gauging technique involves injection of fast neutrons into the formation and analysis of the moderated slow neutron energy distribution by appropriately filtered neutron detectors. The scientific feasibility of the method has been demonstrated by analytical computational and experimental evaluation of the system response. A data analysis method has been developed to determine unambiguously the temperature, neutron absorption cross section and neutron moderating power of an arbitrary medium. The initial phase of a program to demonstrate the engineering feasibility of the technique has been performed. A sonde mockup was fabricated and measurements have been performed in a test stand designed to simulate a geothermal well. The results indicate that the formation temperature determined by this method is independent of differences between the temperature in the borehole fluid and the formation, borehole fluid density, and borehole fluid salinity. Estimates of performance specifications for a formation temperature sonde have been made on the basis of information obtained in this study and a conceptual design of a logging system has been developed. The technique for the determination of fluid flow in a well is based on neutron activation analysis of elements present in the brine. An analytical evaluation of the method has been performed. The results warrant further, experimental evaluation Title: Neutron Formation Temperature Gauge and Neutron Activation Analysis Brine Flow Meter. Final Report, October 1, 1976--March 31, 1978 Author: Vagelatos, N. Year: 1978 Feasibility studies of nuclear techniques applicable to the determination of geothermal formation temperature and two-phase brine flow downhole have been performed. The formation temperature gauging technique involves injection of fast neutrons into the formation and analysis of the moderated slow neutron energy distribution by appropriately filtered neutron detectors. The scientific feasibility of the method has been demonstrated by analytical computational and experimental evaluation of the system response. A data analysis method has been developed to determine unambiguously the temperature, neutron absorption cross section and neutron moderating power of an arbitrary medium. The initial phase of a program to demonstrate the engineering feasibility of the technique has been performed. A sonde mockup was fabricated and measurements have been performed in a test stand designed to simulate a geothermal well. The results indicate that the formation temperature determined by this method is independent of differences between the temperature in the borehole fluid and the formation, borehole fluid density, and borehole fluid salinity. Estimates of performance specifications for a formation temperature sonde have been made on the basis of information obtained in this study and a conceptual design of a logging system has been developed. The technique for the determination of fluid flow in a well is based on neutron activation analysis of elements present in the brine. An analytical evaluation of the method has been performed. The results warrant further, experimental evaluation Close

• 4. [Image] Static Downhole Characteristics of Well CGEH-1 at Coso Hot Springs, China Lake, California

  	A series of measurements was made in the exploratory well CGEH-1 at Coso Hot Springs. The temperature measurements provide estimates for the thermal equilibration of the well and indicate that the fractures ...
  	Citation × Citation Citation Abstract Copy Title: Static Downhole Characteristics of Well CGEH-1 at Coso Hot Springs, China Lake, California Author: Goranson, C. Year: 1978 A series of measurements was made in the exploratory well CGEH-1 at Coso Hot Springs. The temperature measurements provide estimates for the thermal equilibration of the well and indicate that the fractures intersecting the well have different temperatures. The hottest fractures are in the upper-cased portion of the well. Downhole chemical sampling suggests that the borehole still contains remnants of drilling materials. The well has never been extensively flowed at this time Title: Static Downhole Characteristics of Well CGEH-1 at Coso Hot Springs, China Lake, California Author: Goranson, C. Year: 1978 A series of measurements was made in the exploratory well CGEH-1 at Coso Hot Springs. The temperature measurements provide estimates for the thermal equilibration of the well and indicate that the fractures intersecting the well have different temperatures. The hottest fractures are in the upper-cased portion of the well. Downhole chemical sampling suggests that the borehole still contains remnants of drilling materials. The well has never been extensively flowed at this time Close

• 5. [Image] Annual Report on the Project to Design and Experimentally Test an Improved Geothermal Drill Bit

  	Progress is reported in a research and development program to design, build, and test an improved geothermal drill bit. The major tasks of the Phase I effort are entitled: failure mechanisms of existing ...
  	Citation × Citation Citation Abstract Copy Title: Annual Report on the Project to Design and Experimentally Test an Improved Geothermal Drill Bit Author: Barker, L.M. Year: 1976 Progress is reported in a research and development program to design, build, and test an improved geothermal drill bit. The major tasks of the Phase I effort are entitled: failure mechanisms of existing bits; new steels and new bearing design; and new seals and lubricants. It appears that a significant gain in drill-bit life can be attained by the use of higher-temperature steels which retain more hardness at temperatures above 260/sup 0/C (500/sup 0/F). Such steels are available, and two research bits of high-temperature steels were made and will shortly be tested in a laboratory-simulated full-scale geothermal drilling environment. Two control bits of the same design, but made with conventional drill bit steels, were also obtained for identical laboratory test runs, so that the performance of the research bits can be meaningfully assessed. Base-line properties of the steels, such as hardness and fracture toughness as functions of temperature, are being measured to further assess the value of the high-temperature steels selected for the research bits. A geothermal test vessel was designed and fabricated in which the full-scale drill bits will be tested. The vessel is capable of temperature to 427/sup 0/C (800/sup 0/F) and pressures to 35 MPa (5,000 psi). Seal and lubrication designs were studied, and the state of the art in high-temperature seals and lubricants was assessed. Some candidate seals and lubricants have been obtained for testing, and others are being procured. In addition, a seal test vessel has been designed and will soon be completed which can simulate the geothermal drilling environment in full-scale testing of seal and lubricant designs and materials. (JGB) Title: Annual Report on the Project to Design and Experimentally Test an Improved Geothermal Drill Bit Author: Barker, L.M. Year: 1976 Progress is reported in a research and development program to design, build, and test an improved geothermal drill bit. The major tasks of the Phase I effort are entitled: failure mechanisms of existing bits; new steels and new bearing design; and new seals and lubricants. It appears that a significant gain in drill-bit life can be attained by the use of higher-temperature steels which retain more hardness at temperatures above 260/sup 0/C (500/sup 0/F). Such steels are available, and two research bits of high-temperature steels were made and will shortly be tested in a laboratory-simulated full-scale geothermal drilling environment. Two control bits of the same design, but made with conventional drill bit steels, were also obtained for identical laboratory test runs, so that the performance of the research bits can be meaningfully assessed. Base-line properties of the steels, such as hardness and fracture toughness as functions of temperature, are being measured to further assess the value of the high-temperature steels selected for the research bits. A geothermal test vessel was designed and fabricated in which the full-scale drill bits will be tested. The vessel is capable of temperature to 427/sup 0/C (800/sup 0/F) and pressures to 35 MPa (5,000 psi). Seal and lubrication designs were studied, and the state of the art in high-temperature seals and lubricants was assessed. Some candidate seals and lubricants have been obtained for testing, and others are being procured. In addition, a seal test vessel has been designed and will soon be completed which can simulate the geothermal drilling environment in full-scale testing of seal and lubricant designs and materials. (JGB) Close

• 6. [Image] Geological and Geophysical Analysis of Coso Geothermal Exploration Hole No. 1 (CGEH-1), Coso Hot Springs KGRA, California

  	The Coso Geothermal Exploration Hole number one (CGEH-1) was drilled in the Coso Hot Springs KGRA, California from September 2 to December 2, 1977. Chip samples were collected at ten foot intervals and ...
  	Citation × Citation Citation Abstract Copy Title: Geological and Geophysical Analysis of Coso Geothermal Exploration Hole No. 1 (CGEH-1), Coso Hot Springs KGRA, California Author: Galbraith, R.M. Year: 1978 The Coso Geothermal Exploration Hole number one (CGEH-1) was drilled in the Coso Hot Springs KGRA, California from September 2 to December 2, 1977. Chip samples were collected at ten foot intervals and extensive geophysical logging surveys were conducted to document the geologic character of the geothermal system as penetrated by CGEH-1. The major rock units encountered include a mafic metamorphic sequence and a leucogranite which intruded the metamorphic rocks. Only weak hydrothermal alteration was noted in these rocks. Drillhole surveys and drilling rate data indicate that the geothermal system is structurally controlled and that the drillhole itself was strongly influenced by structural zones. Water chemistry indicates that this geothermal resource is a hot-water rather than a vapor-dominated system. Several geophysical logs were employed to characterize the drillhole geology. The natural gamma and neutron porosity logs indicate gross rock type and the acoustic logs indicate fractured rock and potentially permeable zones. A series of temperature logs run as a function of time during and after the completion of Drilling were most Useful in delineating the zones of maximum heat flux. Convective heat flow and temperatures greater than 350/sup 0/F appear to occur only along an open fracture system encountered between depths of 1850 and 2775 feet. Temperature logs indicate a negative thermal gradient below 3000 feet Title: Geological and Geophysical Analysis of Coso Geothermal Exploration Hole No. 1 (CGEH-1), Coso Hot Springs KGRA, California Author: Galbraith, R.M. Year: 1978 The Coso Geothermal Exploration Hole number one (CGEH-1) was drilled in the Coso Hot Springs KGRA, California from September 2 to December 2, 1977. Chip samples were collected at ten foot intervals and extensive geophysical logging surveys were conducted to document the geologic character of the geothermal system as penetrated by CGEH-1. The major rock units encountered include a mafic metamorphic sequence and a leucogranite which intruded the metamorphic rocks. Only weak hydrothermal alteration was noted in these rocks. Drillhole surveys and drilling rate data indicate that the geothermal system is structurally controlled and that the drillhole itself was strongly influenced by structural zones. Water chemistry indicates that this geothermal resource is a hot-water rather than a vapor-dominated system. Several geophysical logs were employed to characterize the drillhole geology. The natural gamma and neutron porosity logs indicate gross rock type and the acoustic logs indicate fractured rock and potentially permeable zones. A series of temperature logs run as a function of time during and after the completion of Drilling were most Useful in delineating the zones of maximum heat flux. Convective heat flow and temperatures greater than 350/sup 0/F appear to occur only along an open fracture system encountered between depths of 1850 and 2775 feet. Temperature logs indicate a negative thermal gradient below 3000 feet Close

• 7. [Image] Potential of Low-Temperature Geothermal Resources in Northern California. Report No. TR13

  	Economically feasible uses for geothermal heat at temperatures too low for conventional electrical power generation at present are delineated. Several geothermal resource areas in northern California that ...
  	Citation × Citation Citation Abstract Copy Title: Potential of Low-Temperature Geothermal Resources in Northern California. Report No. TR13 Author: Hannah, J.L. Year: 1975 Economically feasible uses for geothermal heat at temperatures too low for conventional electrical power generation at present are delineated. Several geothermal resource areas in northern California that have development potential are described, and applications of the heat found in each area are suggested. Plates are included of the following field study areas: the east side of the Sierra-Cascade Range north of Bishop, and the northern Coast Range from San Francisco Bay to Clear Lake. The counties included in the study area are Mo doc, Lassen, Sierra, Plumas, Placer, Alpine, Mono, Mendocino, Lake, and Sonoma. (LBS) Title: Potential of Low-Temperature Geothermal Resources in Northern California. Report No. TR13 Author: Hannah, J.L. Year: 1975 Economically feasible uses for geothermal heat at temperatures too low for conventional electrical power generation at present are delineated. Several geothermal resource areas in northern California that have development potential are described, and applications of the heat found in each area are suggested. Plates are included of the following field study areas: the east side of the Sierra-Cascade Range north of Bishop, and the northern Coast Range from San Francisco Bay to Clear Lake. The counties included in the study area are Mo doc, Lassen, Sierra, Plumas, Placer, Alpine, Mono, Mendocino, Lake, and Sonoma. (LBS) Close

• 8. [Image] Geothermal Heating System for the Children's Museum of Utah

  	The results of a study to determine the engineering and economic feasibility of using the Wasatch Hot Spring resource for space heating of the Children's Library building are presented. The Wasatch Hot ...
  	Citation × Citation Citation Abstract Copy Title: Geothermal Heating System for the Children's Museum of Utah Author: Karlsson, T. Year: 1984 The results of a study to determine the engineering and economic feasibility of using the Wasatch Hot Spring resource for space heating of the Children's Library building are presented. The Wasatch Hot Spring with a reported flow of about 63 gpm (240 l/min) at an average temperature of 104/sup 0/F is not capable of furnishing the needed heat for the Children's Museum building. The underground paths along which the thermal waters flow to their outlets at the Warm Springs Fault are not presently known. It is possible if the thermal water ascends from the deep layers of the earth along the Warm Springs Fault that increased geothermal flow at a higher temperature can be produced by drilling into the fault. Assuming that sufficient geothermal fluid quantity is produced by drilling in the area, an analysis is made of a geothermal heating system for the building based on different fluid temperatures. It is assumed that the present and planned heating systems be left intact with the gas fired boilers taking over during cold periods when the geothermal system fails to provide sufficient heat. Economic analysis shows that the geothermal system is very attractive, even for the lowest geothermal fluid temperature considered (110/sup 0/F) Title: Geothermal Heating System for the Children's Museum of Utah Author: Karlsson, T. Year: 1984 The results of a study to determine the engineering and economic feasibility of using the Wasatch Hot Spring resource for space heating of the Children's Library building are presented. The Wasatch Hot Spring with a reported flow of about 63 gpm (240 l/min) at an average temperature of 104/sup 0/F is not capable of furnishing the needed heat for the Children's Museum building. The underground paths along which the thermal waters flow to their outlets at the Warm Springs Fault are not presently known. It is possible if the thermal water ascends from the deep layers of the earth along the Warm Springs Fault that increased geothermal flow at a higher temperature can be produced by drilling into the fault. Assuming that sufficient geothermal fluid quantity is produced by drilling in the area, an analysis is made of a geothermal heating system for the building based on different fluid temperatures. It is assumed that the present and planned heating systems be left intact with the gas fired boilers taking over during cold periods when the geothermal system fails to provide sufficient heat. Economic analysis shows that the geothermal system is very attractive, even for the lowest geothermal fluid temperature considered (110/sup 0/F) Close

• 9. [Image] Geothermal Resource Exploration in Boise, Idaho

  	Exploratory drilling in Boise, Idaho, in the vicinity of the Boise Front Fault has confirmed the presence of a 170/sup 0/F (77/sup 0/C) geothermal resource below about 800 ft (244 m) near the Veterans ...
  	Citation × Citation Citation Abstract Copy Title: Geothermal Resource Exploration in Boise, Idaho Author: Nelson, L.B. Year: 1980 Exploratory drilling in Boise, Idaho, in the vicinity of the Boise Front Fault has confirmed the presence of a 170/sup 0/F (77/sup 0/C) geothermal resource below about 800 ft (244 m) near the Veterans Hospital of the Military Reserve Park. The Idaho National Engineering Laboratory (INEL), sponsored by the Department of Energy, drilled three exploratory slim holes and two deep exploratory test wells. Study results based on tests of the two exploratory-test wells are reported. Faulting related to the Boise Front Fault defines a major physiographic break in the area that acts as a subsurface conduit through which geothermal water circulates. Hydrologic tests indicate that rocks disturbed by the Boise Front Fault may be as much as ten times more permeable than those removed from the major structural lineament Title: Geothermal Resource Exploration in Boise, Idaho Author: Nelson, L.B. Year: 1980 Exploratory drilling in Boise, Idaho, in the vicinity of the Boise Front Fault has confirmed the presence of a 170/sup 0/F (77/sup 0/C) geothermal resource below about 800 ft (244 m) near the Veterans Hospital of the Military Reserve Park. The Idaho National Engineering Laboratory (INEL), sponsored by the Department of Energy, drilled three exploratory slim holes and two deep exploratory test wells. Study results based on tests of the two exploratory-test wells are reported. Faulting related to the Boise Front Fault defines a major physiographic break in the area that acts as a subsurface conduit through which geothermal water circulates. Hydrologic tests indicate that rocks disturbed by the Boise Front Fault may be as much as ten times more permeable than those removed from the major structural lineament Close

• 10. [Image] Evaluation and Design of Downhole Heat Exchangers for Direct Application; Annual Report, May 1, 1976 - July 1, 1977

  	Progress in an experimental and analytical research program to evaluate and improve the design of downhole heat exchangers (DHEs) for direct applications of geothermal energy is reported. Significant progress ...
  	Citation × Citation Citation Abstract Copy Title: Evaluation and Design of Downhole Heat Exchangers for Direct Application; Annual Report, May 1, 1976 - July 1, 1977 Author: Culver, G.G. Year: 1977 Progress in an experimental and analytical research program to evaluate and improve the design of downhole heat exchangers (DHEs) for direct applications of geothermal energy is reported. Significant progress has been achieved in characterizing flows in wells and without perforated casings and DHEs installed, determination of energy extraction rates for conventional DHEs in both cased and uncased wells, and utilization of information obtained to develop and substantiate models of heat transfer within the well. Flow characterization was obtained by experimentally measuring temperature and velocity profiles. In uncased wells, there was a relatively large vertical temperature gradient (approximately 0.5{sup 0}C/m) and insignificant measured vertical flow, while for the same wells when cased the temperature gradient was essentially zero (approximately 0.03{sup 0}C/m) and a large vertically upward flow was measured (9 to 14 cm/s as measured with a hot-film anemometer). These show that a significant connection cell is established after installation of the casing. The energy extraction rates for a conventional DHE both before and after casing of a 60 m deep well was experimentally measured. In the uncased well up to 300 kW was obtained while the cased well produced over 500 kW. Analytical heat transfer models were developed for the cased well both with and without DHEs. For the cased well without a DHE, the model predicts flow rates that agree with the measured value within about 30 percent. Further, the energy extraction rates predicted by the models agree even better with the measured values. These models allow the energy extraction rates of design parameter variations to be evaluated. At this stage, only trends can be shown but with additional substantiation they should produce optimum energy extraction designs Title: Evaluation and Design of Downhole Heat Exchangers for Direct Application; Annual Report, May 1, 1976 - July 1, 1977 Author: Culver, G.G. Year: 1977 Progress in an experimental and analytical research program to evaluate and improve the design of downhole heat exchangers (DHEs) for direct applications of geothermal energy is reported. Significant progress has been achieved in characterizing flows in wells and without perforated casings and DHEs installed, determination of energy extraction rates for conventional DHEs in both cased and uncased wells, and utilization of information obtained to develop and substantiate models of heat transfer within the well. Flow characterization was obtained by experimentally measuring temperature and velocity profiles. In uncased wells, there was a relatively large vertical temperature gradient (approximately 0.5{sup 0}C/m) and insignificant measured vertical flow, while for the same wells when cased the temperature gradient was essentially zero (approximately 0.03{sup 0}C/m) and a large vertically upward flow was measured (9 to 14 cm/s as measured with a hot-film anemometer). These show that a significant connection cell is established after installation of the casing. The energy extraction rates for a conventional DHE both before and after casing of a 60 m deep well was experimentally measured. In the uncased well up to 300 kW was obtained while the cased well produced over 500 kW. Analytical heat transfer models were developed for the cased well both with and without DHEs. For the cased well without a DHE, the model predicts flow rates that agree with the measured value within about 30 percent. Further, the energy extraction rates predicted by the models agree even better with the measured values. These models allow the energy extraction rates of design parameter variations to be evaluated. At this stage, only trends can be shown but with additional substantiation they should produce optimum energy extraction designs Close