Search

Search Results

• 1. [Image] Annual Report on the Project to Design and Experimentally Test an Improved Geothermal Drill Bit

  	Progress is reported in a research and development program to design, build, and test an improved geothermal drill bit. The major tasks of the Phase I effort are entitled: failure mechanisms of existing ...
  	Citation × Citation Citation Abstract Copy Title: Annual Report on the Project to Design and Experimentally Test an Improved Geothermal Drill Bit Author: Barker, L.M. Year: 1976 Progress is reported in a research and development program to design, build, and test an improved geothermal drill bit. The major tasks of the Phase I effort are entitled: failure mechanisms of existing bits; new steels and new bearing design; and new seals and lubricants. It appears that a significant gain in drill-bit life can be attained by the use of higher-temperature steels which retain more hardness at temperatures above 260/sup 0/C (500/sup 0/F). Such steels are available, and two research bits of high-temperature steels were made and will shortly be tested in a laboratory-simulated full-scale geothermal drilling environment. Two control bits of the same design, but made with conventional drill bit steels, were also obtained for identical laboratory test runs, so that the performance of the research bits can be meaningfully assessed. Base-line properties of the steels, such as hardness and fracture toughness as functions of temperature, are being measured to further assess the value of the high-temperature steels selected for the research bits. A geothermal test vessel was designed and fabricated in which the full-scale drill bits will be tested. The vessel is capable of temperature to 427/sup 0/C (800/sup 0/F) and pressures to 35 MPa (5,000 psi). Seal and lubrication designs were studied, and the state of the art in high-temperature seals and lubricants was assessed. Some candidate seals and lubricants have been obtained for testing, and others are being procured. In addition, a seal test vessel has been designed and will soon be completed which can simulate the geothermal drilling environment in full-scale testing of seal and lubricant designs and materials. (JGB) Title: Annual Report on the Project to Design and Experimentally Test an Improved Geothermal Drill Bit Author: Barker, L.M. Year: 1976 Progress is reported in a research and development program to design, build, and test an improved geothermal drill bit. The major tasks of the Phase I effort are entitled: failure mechanisms of existing bits; new steels and new bearing design; and new seals and lubricants. It appears that a significant gain in drill-bit life can be attained by the use of higher-temperature steels which retain more hardness at temperatures above 260/sup 0/C (500/sup 0/F). Such steels are available, and two research bits of high-temperature steels were made and will shortly be tested in a laboratory-simulated full-scale geothermal drilling environment. Two control bits of the same design, but made with conventional drill bit steels, were also obtained for identical laboratory test runs, so that the performance of the research bits can be meaningfully assessed. Base-line properties of the steels, such as hardness and fracture toughness as functions of temperature, are being measured to further assess the value of the high-temperature steels selected for the research bits. A geothermal test vessel was designed and fabricated in which the full-scale drill bits will be tested. The vessel is capable of temperature to 427/sup 0/C (800/sup 0/F) and pressures to 35 MPa (5,000 psi). Seal and lubrication designs were studied, and the state of the art in high-temperature seals and lubricants was assessed. Some candidate seals and lubricants have been obtained for testing, and others are being procured. In addition, a seal test vessel has been designed and will soon be completed which can simulate the geothermal drilling environment in full-scale testing of seal and lubricant designs and materials. (JGB) Close

• 2. [Image] Geopressured Energy Resource Evaluation

  	The geopressured aquifers that extend along the northern Gulf of Mexico are a large, perhaps the largest, potential source of geothermal energy and natural gas in the US. Because of the high cost of completing ...
  	Citation × Citation Citation Abstract Copy Title: Geopressured Energy Resource Evaluation Author: Samuels, G. Year: 1979 The geopressured aquifers that extend along the northern Gulf of Mexico are a large, perhaps the largest, potential source of geothermal energy and natural gas in the US. Because of the high cost of completing wells into these formations and their relatively low temperatures (200 to 400 F), the utilization of the geothermal energy will be highly depend on, and of secondary importance to, the value of the methane. The economics of extracting either the geothermal energy or natural gas from these aquifers does not look promising. The combined requirements of high well flow rates (40,000 bbl/day), long life (20 years), and the necessity for close well spacing to minimize the cost of the collection system may be incompatible with the actual characteristics of the reservoirs. These factors place such stringent requirements on the reservoir size, permeability, and compressibility, or specific storage coefficient, that the number of promising production areas may be severely limited Title: Geopressured Energy Resource Evaluation Author: Samuels, G. Year: 1979 The geopressured aquifers that extend along the northern Gulf of Mexico are a large, perhaps the largest, potential source of geothermal energy and natural gas in the US. Because of the high cost of completing wells into these formations and their relatively low temperatures (200 to 400 F), the utilization of the geothermal energy will be highly depend on, and of secondary importance to, the value of the methane. The economics of extracting either the geothermal energy or natural gas from these aquifers does not look promising. The combined requirements of high well flow rates (40,000 bbl/day), long life (20 years), and the necessity for close well spacing to minimize the cost of the collection system may be incompatible with the actual characteristics of the reservoirs. These factors place such stringent requirements on the reservoir size, permeability, and compressibility, or specific storage coefficient, that the number of promising production areas may be severely limited Close

• 3. [Image] Geothermal Investigations in Idaho. Part 8. Heat Flow Study of the Snake River Plain Region, Idaho

  	The Snake River Plain of Idaho has recent lava flows and a large number of thermal springs and wells. A heat flow study was initiated which, together with available geological and geophysical information, ...
  	Citation × Citation Citation Abstract Copy Title: Geothermal Investigations in Idaho. Part 8. Heat Flow Study of the Snake River Plain Region, Idaho Author: Brott, C.A. Year: 1976 The Snake River Plain of Idaho has recent lava flows and a large number of thermal springs and wells. A heat flow study was initiated which, together with available geological and geophysical information, allows a better definition of the geothermal resource and evaluation of the geothermal potential. Local geothermal anomalies were not the objects of this study and have not been studied in detail. The quality of the heat flow values obtained varies as interpretation was necessary to determine geothermal gradients for many of the holes which had disturbances. A major problem in determining the heat flow values is the lack of knowledge of the in situ porosity of the rocks. The heat flow values obtained for the Eastern Snake River Plain are from shallow wells (< 200 m), hence the heat flow there is low (< 0.5 HFU) because of the water movement in the Snake Plain aquifer. The anomalous regional heat flow pattern around the Snake River Plain, together with other geophysical and geological data, suggest the presence of a major crustal heat source. With the exception of the area of the Snake Plain aquifer, high geothermal gradients were found in all areas of southern Idaho (40 to 100/sup 0/C/km). Temperatures hot enough for space heating can be found most anywhere in the Plain at relatively shallow depths (1 to 2 km). Temperatures hot enough for electrical power generation (200/sup 0/C) can be found beneath southern Idaho almost anywhere at depths of 3 to 4 kilometers. The Plain is fault bounded and hot water circulating along the fault zones from depths can be a very important geothermal resource at shallow depths. The margins of the Plain have the highest heat flow values, are the most faulted, and have possibly the highest geothermal resource potential Title: Geothermal Investigations in Idaho. Part 8. Heat Flow Study of the Snake River Plain Region, Idaho Author: Brott, C.A. Year: 1976 The Snake River Plain of Idaho has recent lava flows and a large number of thermal springs and wells. A heat flow study was initiated which, together with available geological and geophysical information, allows a better definition of the geothermal resource and evaluation of the geothermal potential. Local geothermal anomalies were not the objects of this study and have not been studied in detail. The quality of the heat flow values obtained varies as interpretation was necessary to determine geothermal gradients for many of the holes which had disturbances. A major problem in determining the heat flow values is the lack of knowledge of the in situ porosity of the rocks. The heat flow values obtained for the Eastern Snake River Plain are from shallow wells (< 200 m), hence the heat flow there is low (< 0.5 HFU) because of the water movement in the Snake Plain aquifer. The anomalous regional heat flow pattern around the Snake River Plain, together with other geophysical and geological data, suggest the presence of a major crustal heat source. With the exception of the area of the Snake Plain aquifer, high geothermal gradients were found in all areas of southern Idaho (40 to 100/sup 0/C/km). Temperatures hot enough for space heating can be found most anywhere in the Plain at relatively shallow depths (1 to 2 km). Temperatures hot enough for electrical power generation (200/sup 0/C) can be found beneath southern Idaho almost anywhere at depths of 3 to 4 kilometers. The Plain is fault bounded and hot water circulating along the fault zones from depths can be a very important geothermal resource at shallow depths. The margins of the Plain have the highest heat flow values, are the most faulted, and have possibly the highest geothermal resource potential Close

• 4. [Image] The Marysville, Montana Geothermal Project (Revised)

  	The object of the Marysville Geothermal Project is to investigate a region of abnormally high geothermal heat flow near Marysville, MT, about 20 miles northwest of Helena. The research should determine ...
  	Citation × Citation Citation Abstract Copy Title: The Marysville, Montana Geothermal Project (Revised) Author: McSpadden, W.R. Year: 1974 The object of the Marysville Geothermal Project is to investigate a region of abnormally high geothermal heat flow near Marysville, MT, about 20 miles northwest of Helena. The research should determine the nature and size of the resource, how the energy might be extracted, the potential monetary value of the energy, and how similar resources elsewhere might be located. The heat source was expected to be a granitic pluton or magmatic intrusion, 10,000 to 40,000 years old, with temperatures in the range of 300 to 500°C. Originally it was thought that the pluton was at relatively shallow depths, but at present its depth and exact location are unknown Title: The Marysville, Montana Geothermal Project (Revised) Author: McSpadden, W.R. Year: 1974 The object of the Marysville Geothermal Project is to investigate a region of abnormally high geothermal heat flow near Marysville, MT, about 20 miles northwest of Helena. The research should determine the nature and size of the resource, how the energy might be extracted, the potential monetary value of the energy, and how similar resources elsewhere might be located. The heat source was expected to be a granitic pluton or magmatic intrusion, 10,000 to 40,000 years old, with temperatures in the range of 300 to 500°C. Originally it was thought that the pluton was at relatively shallow depths, but at present its depth and exact location are unknown Close

• 5. [Image] Development of the high-temperature redox electrode. Interim report ending March 1980

  	The oxidation-reduction (known as redox) electrode was studied in a pH range corresponding to that found in a CO/sub 2/-silicate buffered system at temperatures ranging from 100 to 250/sup 0/C. Oxidizing ...
  	Citation × Citation Citation Abstract Copy Title: Development of the high-temperature redox electrode. Interim report ending March 1980 Author: Danielson, M.J. Year: 1980 The oxidation-reduction (known as redox) electrode was studied in a pH range corresponding to that found in a CO/sub 2/-silicate buffered system at temperatures ranging from 100 to 250/sup 0/C. Oxidizing conditions were created by injecting oxygen; the greatest reducing conditions, by using hydrogen. The sulfur system (H/sub 2/S, HS/sup -/, S/sup 2/) was not examined at this time, but future work will include this system since it is an important component of the geothermal brine. Both a platinized platinum (Pt-Pt) and a bare platinum (Pt-foil) electrode respond to the redox environment. The response does not appear to indicate thermodynamic equilibrium with the chemical environment; instead a mixed potential response is indicated. The difference in potential between a strong oxidizing environment (0.4-ppM O/sub 2/) and a strong reducing environment (0.5-atm H/sub 2/) is typically > 1 volt at all temperatures. The magnitude of this response makes the platinum electrode a suitable sensor for continuous monitoring of the geothermal environment for oxygen intrusions. The platinized platinum redox electrode is superior to the bare platinum electrode; PNL-3377 Title: Development of the high-temperature redox electrode. Interim report ending March 1980 Author: Danielson, M.J. Year: 1980 The oxidation-reduction (known as redox) electrode was studied in a pH range corresponding to that found in a CO/sub 2/-silicate buffered system at temperatures ranging from 100 to 250/sup 0/C. Oxidizing conditions were created by injecting oxygen; the greatest reducing conditions, by using hydrogen. The sulfur system (H/sub 2/S, HS/sup -/, S/sup 2/) was not examined at this time, but future work will include this system since it is an important component of the geothermal brine. Both a platinized platinum (Pt-Pt) and a bare platinum (Pt-foil) electrode respond to the redox environment. The response does not appear to indicate thermodynamic equilibrium with the chemical environment; instead a mixed potential response is indicated. The difference in potential between a strong oxidizing environment (0.4-ppM O/sub 2/) and a strong reducing environment (0.5-atm H/sub 2/) is typically > 1 volt at all temperatures. The magnitude of this response makes the platinum electrode a suitable sensor for continuous monitoring of the geothermal environment for oxygen intrusions. The platinized platinum redox electrode is superior to the bare platinum electrode; PNL-3377 Close

• 6. [Image] Field Electrochemical Measurements of Corrosion Characteristics of Materials in Hypersaline Geothermal Brine

  	A flow cell (with appropriate accessories) was developed for use in short-term testing of the corrosion behavior of materials in approximately 100{sup 0}C, hypersaline geothermal brine. The apparatus was ...
  	Citation × Citation Citation Abstract Copy Title: Field Electrochemical Measurements of Corrosion Characteristics of Materials in Hypersaline Geothermal Brine Author: Harrar, J.E. Year: 1977 A flow cell (with appropriate accessories) was developed for use in short-term testing of the corrosion behavior of materials in approximately 100{sup 0}C, hypersaline geothermal brine. The apparatus was designed to accommodate commercial (Petrolite) corrosion measurement equipment and conducted experiments on-line at the Lawrence Livermore Laboratory Test Station in the Salton Sea Geothermal Field. The apparatus also permitted direct readings of corrosion potentials, solution redox potential (E{sub h}), brine flow rate, pH, and temperature. Estimates of general corrosion rates were obtained by the linear polarization resistance technique and from measurements of complete potentiodynamic polarization curves. The latter also afforded predictions of pitting susceptibilities of active-passive type materials. Twenty-two alloys (with various heat treatments) were tested and readily grouped according to general corrosion resistances in acidified hypersaline (approximately 4 M chloride) brine. Especially promising in regard to corrosion resistance-vs-cost is the series of low Cr--Mo steels. Prescaling of materials in unacidified (pH approximately 5.7) brine prior to exposure to acidified (pH 2 to 4.5) brine was found to be beneficial in reducing corrosion rates at 100{sup 0}C Title: Field Electrochemical Measurements of Corrosion Characteristics of Materials in Hypersaline Geothermal Brine Author: Harrar, J.E. Year: 1977 A flow cell (with appropriate accessories) was developed for use in short-term testing of the corrosion behavior of materials in approximately 100{sup 0}C, hypersaline geothermal brine. The apparatus was designed to accommodate commercial (Petrolite) corrosion measurement equipment and conducted experiments on-line at the Lawrence Livermore Laboratory Test Station in the Salton Sea Geothermal Field. The apparatus also permitted direct readings of corrosion potentials, solution redox potential (E{sub h}), brine flow rate, pH, and temperature. Estimates of general corrosion rates were obtained by the linear polarization resistance technique and from measurements of complete potentiodynamic polarization curves. The latter also afforded predictions of pitting susceptibilities of active-passive type materials. Twenty-two alloys (with various heat treatments) were tested and readily grouped according to general corrosion resistances in acidified hypersaline (approximately 4 M chloride) brine. Especially promising in regard to corrosion resistance-vs-cost is the series of low Cr--Mo steels. Prescaling of materials in unacidified (pH approximately 5.7) brine prior to exposure to acidified (pH 2 to 4.5) brine was found to be beneficial in reducing corrosion rates at 100{sup 0}C Close

• 7. [Image] Geothermal Exploration of the Puga and Chumathang Geothermal Fields, Ladakh, India

  	Puga and Chumathang Geothermal fields are situated near the collided junction of the Indian and Asian Crystal plates and thermal activity in these fields is attributed to the widespread igneous activity ...
  	Citation × Citation Citation Abstract Copy Title: Geothermal Exploration of the Puga and Chumathang Geothermal Fields, Ladakh, India Author: Shanker, R. Puga and Chumathang Geothermal fields are situated near the collided junction of the Indian and Asian Crystal plates and thermal activity in these fields is attributed to the widespread igneous activity of Upper Cretaceous to late Tertiary age. A deep suture zone, recognised in between these two fields and the associated faults provide channels for the upward migration of the thermal fluids. High concentrations of Cl, F, Si02, B, Na, Li, Rb, Cs in thermal fluids signify contribution of magmatic bodies towards heat, and fluid supply. These fields are characterized by high heat flow conditions (13 HFU), abnormal shallow geothermal gradients (0.7 - 2.5 c/m) , high base temperature (220 - 270 C) as obtained by alkalia and Ne-K-Ca geothermometry and low resistivity values (2-20 ohm.m.). Low resistivity zones occupy on an area of three and one sq.km. and extend down to maximum depths of 300 m. and 130 m. at Puga and Chumathang respectively. Shallow drilling (28-130 m.) has established the existence of wet steam reservoirs under moderate pressure (2-4.5 kg/cm^2). Hot fluid (95-135 C) discharges from eight flowing wells ranged from 7.5 to 30 t/h. These thermal fluids are stored in the partly consolidated fluvioglacial deposits of Quarternary to Recent age. The occurrence of a limestone layer in the country rock at Puga brightens the prospects of getting good reservoir at depth. In both these fields two aquifers have been recognised, each having sizeable potential for retaining ground water. The ground water recharge is mainly through snow melt from glaciers in the case of Puga field and principally from Indus river in the case of Chumathangfield Title: Geothermal Exploration of the Puga and Chumathang Geothermal Fields, Ladakh, India Author: Shanker, R. Puga and Chumathang Geothermal fields are situated near the collided junction of the Indian and Asian Crystal plates and thermal activity in these fields is attributed to the widespread igneous activity of Upper Cretaceous to late Tertiary age. A deep suture zone, recognised in between these two fields and the associated faults provide channels for the upward migration of the thermal fluids. High concentrations of Cl, F, Si02, B, Na, Li, Rb, Cs in thermal fluids signify contribution of magmatic bodies towards heat, and fluid supply. These fields are characterized by high heat flow conditions (13 HFU), abnormal shallow geothermal gradients (0.7 - 2.5 c/m) , high base temperature (220 - 270 C) as obtained by alkalia and Ne-K-Ca geothermometry and low resistivity values (2-20 ohm.m.). Low resistivity zones occupy on an area of three and one sq.km. and extend down to maximum depths of 300 m. and 130 m. at Puga and Chumathang respectively. Shallow drilling (28-130 m.) has established the existence of wet steam reservoirs under moderate pressure (2-4.5 kg/cm^2). Hot fluid (95-135 C) discharges from eight flowing wells ranged from 7.5 to 30 t/h. These thermal fluids are stored in the partly consolidated fluvioglacial deposits of Quarternary to Recent age. The occurrence of a limestone layer in the country rock at Puga brightens the prospects of getting good reservoir at depth. In both these fields two aquifers have been recognised, each having sizeable potential for retaining ground water. The ground water recharge is mainly through snow melt from glaciers in the case of Puga field and principally from Indus river in the case of Chumathangfield Close

• 8. [Image] Utilization of geothermal energy for methane production for J. A. Albertson Land and Cattle Company

  	To utilize the geothermal energy in the area of its 30,000-head cattle feedlot, J.A. Albertson Land and Cattle Co. is considering the development of an integrated geothermal/bioconversion system that would ...
  	Citation × Citation Citation Abstract Copy Title: Utilization of geothermal energy for methane production for J. A. Albertson Land and Cattle Company Author: Bissell, R.R. Year: 1980 To utilize the geothermal energy in the area of its 30,000-head cattle feedlot, J.A. Albertson Land and Cattle Co. is considering the development of an integrated geothermal/bioconversion system that would use the cattle manure as a feedstock for an anaerobic-digestion plant to produce methane plus a digester-residue cattle-feed supplement. The feedlot lies within a high-temperature gradient and heat-flow area associated with the Western Snake River basin in Malheur Co., Oregon. The three digesters designed for the process will operate mesophilically (at 98/sup 0/F) with a 20-day retention time. To make up the digesters' heat losses, the geothermal water source will need to be about 135/sup 0/F and have a flow rate of 120-240 gpm, depending on the size ultimately selected for the facility. If the digester residue replaces alfalfa hay in the cattle's current rations, its value will amount to $1.15 million/yr. Burning the methane in engine/generator sets would produce 985-1970 kW of electric power that could be either sold or used as a day-to-day substitute for the geothermal heat. An economic analysis of the system is presented; DOE/ET/27230-T2 Title: Utilization of geothermal energy for methane production for J. A. Albertson Land and Cattle Company Author: Bissell, R.R. Year: 1980 To utilize the geothermal energy in the area of its 30,000-head cattle feedlot, J.A. Albertson Land and Cattle Co. is considering the development of an integrated geothermal/bioconversion system that would use the cattle manure as a feedstock for an anaerobic-digestion plant to produce methane plus a digester-residue cattle-feed supplement. The feedlot lies within a high-temperature gradient and heat-flow area associated with the Western Snake River basin in Malheur Co., Oregon. The three digesters designed for the process will operate mesophilically (at 98/sup 0/F) with a 20-day retention time. To make up the digesters' heat losses, the geothermal water source will need to be about 135/sup 0/F and have a flow rate of 120-240 gpm, depending on the size ultimately selected for the facility. If the digester residue replaces alfalfa hay in the cattle's current rations, its value will amount to $1.15 million/yr. Burning the methane in engine/generator sets would produce 985-1970 kW of electric power that could be either sold or used as a day-to-day substitute for the geothermal heat. An economic analysis of the system is presented; DOE/ET/27230-T2 Close

• 9. [Image] ASP: An Automated Seismic Processor for Microearthquake Networks

  	ASP, a low-power, in-field Automated Seismic Processor of microearthquake network data has been designed, fabricated, and deployed for initial operation in four different field areas to monitor seismicity ...
  	Citation × Citation Citation Abstract Copy Title: ASP: An Automated Seismic Processor for Microearthquake Networks Author: McEvilly, T. V. Year: 1981 ASP, a low-power, in-field Automated Seismic Processor of microearthquake network data has been designed, fabricated, and deployed for initial operation in four different field areas to monitor seismicity associated with two geothermal areas (The Geysers, California, and Cerro Prieto, Mexico), a nuclear explosion with its related collapse and aftershock sequence, and late (> 1 year) activity in a major aftershock series (Livermore, California). A second ASP system, with a high-speed front-end, is used in acoustic emission (1-20 kHz) analysis for fracture monitoring. Each of the 15 channels of ASP (configured for up to 128 channels) automatically detects, measures times and amplitudes, and computes and fits FFr's for both the P and S waves on data sampled at 100 samples/sec. These data from each channel are then processed with a central microprocessor for hypocenter location, running b-values, source parameters, event count, and P-wave polarities. The system is capable of processing a 15-station detection in approximately 40 seconds, excluding print-out. The initial trials have demonstrated that infield real-time analysis of data maximizes the efficiency of microearthquake surveys allowing flexibility in experimental procedures, with a minimum of the traditional labor-intensive postprocessing. Current efforts are directed towards improving efficiency of computation and data output and in expanding software capabilities Title: ASP: An Automated Seismic Processor for Microearthquake Networks Author: McEvilly, T. V. Year: 1981 ASP, a low-power, in-field Automated Seismic Processor of microearthquake network data has been designed, fabricated, and deployed for initial operation in four different field areas to monitor seismicity associated with two geothermal areas (The Geysers, California, and Cerro Prieto, Mexico), a nuclear explosion with its related collapse and aftershock sequence, and late (> 1 year) activity in a major aftershock series (Livermore, California). A second ASP system, with a high-speed front-end, is used in acoustic emission (1-20 kHz) analysis for fracture monitoring. Each of the 15 channels of ASP (configured for up to 128 channels) automatically detects, measures times and amplitudes, and computes and fits FFr's for both the P and S waves on data sampled at 100 samples/sec. These data from each channel are then processed with a central microprocessor for hypocenter location, running b-values, source parameters, event count, and P-wave polarities. The system is capable of processing a 15-station detection in approximately 40 seconds, excluding print-out. The initial trials have demonstrated that infield real-time analysis of data maximizes the efficiency of microearthquake surveys allowing flexibility in experimental procedures, with a minimum of the traditional labor-intensive postprocessing. Current efforts are directed towards improving efficiency of computation and data output and in expanding software capabilities Close

• 10. [Image] Research on the Physical Properties of Geothermal Reservoir Rock. Quarterly Report, March 1978

  	A laboratory study of the P-wave velocity and electric Resistivity was undertaken on Cenozoic Volcanic Rocks collected from the Columbia Plateau Volcanic basin (C) and the Jemez Volcanic field (NM). Electric ...
  	Citation × Citation Citation Abstract Copy Title: Research on the Physical Properties of Geothermal Reservoir Rock. Quarterly Report, March 1978 Author: Keller, G.V. Year: 1978 A laboratory study of the P-wave velocity and electric Resistivity was undertaken on Cenozoic Volcanic Rocks collected from the Columbia Plateau Volcanic basin (C) and the Jemez Volcanic field (NM). Electric resistivities of cylindrical samples saturated with 0.1 N NaCl solution were measured using a four electrode system and a 1.0 KHz frequency source. Seismic P-wave velocities were calculated from measured transit time of mechanical pulses generated and received by piezoelectric transducers. The electric Resistivity of water saturated Samples decreased as temperature increased to the boiling point of water. Above boiling point, Resistivity increased rapidly as water changed to vapor. Resistivity is most sensitive to temperature changes between 35/sup 0/C to 65/sup 0/C. Resistivities of samples increased with decrease in saturation. The effect is more pronounced at lower temperatures. No dependence of seismic P-wave velocities on temperature was observed. Both Resistivity and P-wave velocity depend on porosity. The increase in porosity results in a decrease in the Resistivity formation factor. Assuming a relationship FF = a phi/sup -m/ (Archie's Law), where FF and phi represent the formation factor and porosity respectively, least squares indicate a variation of a between .5 and 2.0. The value of m varied between 1.2 to 1.7. Seismic velocities (v) decrease as porosity increases. Porosity appears to be linearly related to log v. Several Samples show anomalous relationship between porosity and Resistivity. Most of these samples also show anomalous seismic velocities. The majority of these samples have coarse grains or large pores. The effect of saturation on P-wave velocity is small and can be observed in few samples. In these samples, seismic velocities decrease with increase in saturation at high saturation (100% to 85%), and show a reverse relationship at low saturation. Between 15% and 85% saturation in velocity is constant Title: Research on the Physical Properties of Geothermal Reservoir Rock. Quarterly Report, March 1978 Author: Keller, G.V. Year: 1978 A laboratory study of the P-wave velocity and electric Resistivity was undertaken on Cenozoic Volcanic Rocks collected from the Columbia Plateau Volcanic basin (C) and the Jemez Volcanic field (NM). Electric resistivities of cylindrical samples saturated with 0.1 N NaCl solution were measured using a four electrode system and a 1.0 KHz frequency source. Seismic P-wave velocities were calculated from measured transit time of mechanical pulses generated and received by piezoelectric transducers. The electric Resistivity of water saturated Samples decreased as temperature increased to the boiling point of water. Above boiling point, Resistivity increased rapidly as water changed to vapor. Resistivity is most sensitive to temperature changes between 35/sup 0/C to 65/sup 0/C. Resistivities of samples increased with decrease in saturation. The effect is more pronounced at lower temperatures. No dependence of seismic P-wave velocities on temperature was observed. Both Resistivity and P-wave velocity depend on porosity. The increase in porosity results in a decrease in the Resistivity formation factor. Assuming a relationship FF = a phi/sup -m/ (Archie's Law), where FF and phi represent the formation factor and porosity respectively, least squares indicate a variation of a between .5 and 2.0. The value of m varied between 1.2 to 1.7. Seismic velocities (v) decrease as porosity increases. Porosity appears to be linearly related to log v. Several Samples show anomalous relationship between porosity and Resistivity. Most of these samples also show anomalous seismic velocities. The majority of these samples have coarse grains or large pores. The effect of saturation on P-wave velocity is small and can be observed in few samples. In these samples, seismic velocities decrease with increase in saturation at high saturation (100% to 85%), and show a reverse relationship at low saturation. Between 15% and 85% saturation in velocity is constant Close