Search

Search Results

• 1. [Image] Investigations of the Dunes Geothermal Anomaly, Imperial Valley, California: Part 1. Geochemistry of Geothermal Fluid

  	A geothermal test borehole, DWR Dunes No. 1, was drilled in the Dunes geothermal anomaly by the State of California Department of Water Resources. Water samples from this geothermal system were collected ...
  	Citation × Citation Citation Abstract Copy Title: Investigations of the Dunes Geothermal Anomaly, Imperial Valley, California: Part 1. Geochemistry of Geothermal Fluid Author: Coplen, T.B. Year: 1974 A geothermal test borehole, DWR Dunes No. 1, was drilled in the Dunes geothermal anomaly by the State of California Department of Water Resources. Water samples from this geothermal system were collected from perforations at 109 and 260 meters depth. These water samples were analyzed for chemical and isotopic composition. These tests indicate that the source of the geothermal fluid is partially evaporated Colorado River water. An investigation of chloride/bromide ratios was used to determine the source of the salt in the geothermal fluid from Dunes. The result may suggest that the salt in the Salton Sea geothermal system and in the Dunes geothermal anomaly is derived from the Colorado River and that this water has not done any leaching or been mixed with water from other sources. It was determined that further geophysical Studies (gravity, seismic refraction, electrical resistivity, and magnetotelluric sounding) are needed to locate the reservoir of geothermal fluid in the Dunes system Title: Investigations of the Dunes Geothermal Anomaly, Imperial Valley, California: Part 1. Geochemistry of Geothermal Fluid Author: Coplen, T.B. Year: 1974 A geothermal test borehole, DWR Dunes No. 1, was drilled in the Dunes geothermal anomaly by the State of California Department of Water Resources. Water samples from this geothermal system were collected from perforations at 109 and 260 meters depth. These water samples were analyzed for chemical and isotopic composition. These tests indicate that the source of the geothermal fluid is partially evaporated Colorado River water. An investigation of chloride/bromide ratios was used to determine the source of the salt in the geothermal fluid from Dunes. The result may suggest that the salt in the Salton Sea geothermal system and in the Dunes geothermal anomaly is derived from the Colorado River and that this water has not done any leaching or been mixed with water from other sources. It was determined that further geophysical Studies (gravity, seismic refraction, electrical resistivity, and magnetotelluric sounding) are needed to locate the reservoir of geothermal fluid in the Dunes system Close

• 2. [Image] Comparative assessment of five potential sites for hydrothermal-magma systems: summary

  	A comparative assessment of five potential hydrothermal-magma sites for this facet of the Thermal Regimes part of the CSDP has been prepared for the DOE Office of Basic Energy Sciences. The five sites ...
  	Citation × Citation Citation Abstract Copy Title: Comparative assessment of five potential sites for hydrothermal-magma systems: summary Author: Luth, W.C Year: 1980 A comparative assessment of five potential hydrothermal-magma sites for this facet of the Thermal Regimes part of the CSDP has been prepared for the DOE Office of Basic Energy Sciences. The five sites are: The Geysers-Clear Lake, CA, Long Valley, CA, Rio Grande Rift, NM, Roosevelt Hot Springs, UT, and Salton Trough, CA. This site assessment study has drawn together background information (geology, geochemistry, geophysics, and energy transport) on the five sites as a preliminary stage to site selection. Criteria for site selection are that potential sites have identifiable, or likely, hydrothermal systems and associated magma sources, and the important scientific questions can be identified and answered by deep scientific holes. Recommendations were made.; DOE/TIC-11303 Title: Comparative assessment of five potential sites for hydrothermal-magma systems: summary Author: Luth, W.C Year: 1980 A comparative assessment of five potential hydrothermal-magma sites for this facet of the Thermal Regimes part of the CSDP has been prepared for the DOE Office of Basic Energy Sciences. The five sites are: The Geysers-Clear Lake, CA, Long Valley, CA, Rio Grande Rift, NM, Roosevelt Hot Springs, UT, and Salton Trough, CA. This site assessment study has drawn together background information (geology, geochemistry, geophysics, and energy transport) on the five sites as a preliminary stage to site selection. Criteria for site selection are that potential sites have identifiable, or likely, hydrothermal systems and associated magma sources, and the important scientific questions can be identified and answered by deep scientific holes. Recommendations were made.; DOE/TIC-11303 Close

• 3. [Image] Comparative assessment of five potential sites for hydrothermal-magma systems: energy transport

  	A comparative assessment of five sites is being prepared as part of a Continental Scientific Drilling Program (CSDP) review of thermal regimes for the purpose of scoping areas for future research and drilling ...
  	Citation × Citation Citation Abstract Copy Title: Comparative assessment of five potential sites for hydrothermal-magma systems: energy transport Author: Hardee, H.C. Year: 1980 A comparative assessment of five sites is being prepared as part of a Continental Scientific Drilling Program (CSDP) review of thermal regimes for the purpose of scoping areas for future research and drilling activities. This background report: discusses the various energy transport processes likely to be encountered in a hydrothermal-magma system, reviews related literature, discusses research and field data needs, and reviews the sites from an energy transport viewpoint. At least three major zones exist in the magma-hydrothermal transport system: the magma zone, the hydrothermal zone, and the transition zone between the two. Major energy transport questions relate to the nature and existence of these zones and their evolution with time. Additional energy transport questions are concerned with the possible existence of critical state and super-critical state permeable convection in deep geothermal systems. A review of thermal transport models emphasizes the fact that present transport models and computational techniques far outweigh the scarcity and quality of deep field data. Title: Comparative assessment of five potential sites for hydrothermal-magma systems: energy transport Author: Hardee, H.C. Year: 1980 A comparative assessment of five sites is being prepared as part of a Continental Scientific Drilling Program (CSDP) review of thermal regimes for the purpose of scoping areas for future research and drilling activities. This background report: discusses the various energy transport processes likely to be encountered in a hydrothermal-magma system, reviews related literature, discusses research and field data needs, and reviews the sites from an energy transport viewpoint. At least three major zones exist in the magma-hydrothermal transport system: the magma zone, the hydrothermal zone, and the transition zone between the two. Major energy transport questions relate to the nature and existence of these zones and their evolution with time. Additional energy transport questions are concerned with the possible existence of critical state and super-critical state permeable convection in deep geothermal systems. A review of thermal transport models emphasizes the fact that present transport models and computational techniques far outweigh the scarcity and quality of deep field data. Close

• 4. [Image] DHE (Downhole Heat Exchangers)

  	The use of downhole heat exchangers (DHE) for residential or commercial space and domestic water heating and other applications has several desirable features. Systems are nearly or completely passive ...
  	Citation × Citation Citation Abstract Copy Title: DHE (Downhole Heat Exchangers) Author: Culver, G. Year: 1990 The use of downhole heat exchangers (DHE) for residential or commercial space and domestic water heating and other applications has several desirable features. Systems are nearly or completely passive -- that is, no or very little geothermal water or steam is produced from the well either reducing or completely eliminating surface environmental concerns and the need for disposal systems or injection wells. Initial cost of pumps and installation are eliminated or reduced along with pumping power costs and maintenance costs associated with pumping often corrosive geothermal fluids. Many residential and small commercial systems do not require circulating pumps because the density difference in the incoming and outgoing sides of the loop are sufficient to overcome circulating friction losses in the entire system. The major disadvantage of DHEs is their dependence on natural heat flow. In areas where geological conditions provide high permeability and a natural hydraulic gradient, DHEs can provide a substantial quantity of heat. A single 500-ft (152 m) well in Klamath Falls, Oregon, supplies over one megawatt thermal and output is apparently limited by the surface area of pipe that can be installed in the well bore. In contrast, DHEs used in conjunction with heat pumps may supply less than 8 KW from a well of similar depth. Here output is limited by conductive heat flow with perhaps a small contribution from convection near the well bore. The highest capacity DHE reported to date, in Turkey, supplies 6 MW thermal from an 820-ft (250 m) well. There were two main goals for this project. The first was to gather, disseminate and exchange internationally information on DHEs. The second was to perform experiments that would provide insight into well bore/aquifer interaction and thereby provide more information on which to base DHE designs. 27 refs., 31 figs., 3 tabs. Title: DHE (Downhole Heat Exchangers) Author: Culver, G. Year: 1990 The use of downhole heat exchangers (DHE) for residential or commercial space and domestic water heating and other applications has several desirable features. Systems are nearly or completely passive -- that is, no or very little geothermal water or steam is produced from the well either reducing or completely eliminating surface environmental concerns and the need for disposal systems or injection wells. Initial cost of pumps and installation are eliminated or reduced along with pumping power costs and maintenance costs associated with pumping often corrosive geothermal fluids. Many residential and small commercial systems do not require circulating pumps because the density difference in the incoming and outgoing sides of the loop are sufficient to overcome circulating friction losses in the entire system. The major disadvantage of DHEs is their dependence on natural heat flow. In areas where geological conditions provide high permeability and a natural hydraulic gradient, DHEs can provide a substantial quantity of heat. A single 500-ft (152 m) well in Klamath Falls, Oregon, supplies over one megawatt thermal and output is apparently limited by the surface area of pipe that can be installed in the well bore. In contrast, DHEs used in conjunction with heat pumps may supply less than 8 KW from a well of similar depth. Here output is limited by conductive heat flow with perhaps a small contribution from convection near the well bore. The highest capacity DHE reported to date, in Turkey, supplies 6 MW thermal from an 820-ft (250 m) well. There were two main goals for this project. The first was to gather, disseminate and exchange internationally information on DHEs. The second was to perform experiments that would provide insight into well bore/aquifer interaction and thereby provide more information on which to base DHE designs. 27 refs., 31 figs., 3 tabs. Close

• 5. [Image] Dipole-Dipole Resistivity Surveys, Roosevelt Hot Springs KGRA. Final Report, Volume 2

  	Dipole-dipole Resistivity surveys were conducted at Roosevelt Hot Springs KGRA. Three different dipole spacings were used; 99km of traverse line were surveyed with 100m dipoles, 50km with 300m dipoles, ...
  	Citation × Citation Citation Abstract Copy Title: Dipole-Dipole Resistivity Surveys, Roosevelt Hot Springs KGRA. Final Report, Volume 2 Author: Ward, S.H. Year: 1976 Dipole-dipole Resistivity surveys were conducted at Roosevelt Hot Springs KGRA. Three different dipole spacings were used; 99km of traverse line were surveyed with 100m dipoles, 50km with 300m dipoles, and 44km with 1km dipoles. The objectives of the Resistivity surveying were to detect and delineate regions of low Resistivity associated with fracturing, brines, high temperatures, and clay alteration. The Resistivity of rocks that are typical of hydrothermal environments is due to two main conduction mechanisms: (1) electrolytic conduction through pores and fractures; and (2) surface conduction due to a thin zone of cations attracted to those mineral surfaces with net negative charges (especially clay minerals). For saturated rocks, the Resistivity due to electrolytic conduction is a function of the effective porosity of the fractured rock, of the temperature, and of the salinity of the fluid filling the pores and fractures. The Resistivity decreases as the effective porosity, water saturation, salinity, and temperature increase. The presence of clay minerals and pyrite will also decrease the Resistivity Title: Dipole-Dipole Resistivity Surveys, Roosevelt Hot Springs KGRA. Final Report, Volume 2 Author: Ward, S.H. Year: 1976 Dipole-dipole Resistivity surveys were conducted at Roosevelt Hot Springs KGRA. Three different dipole spacings were used; 99km of traverse line were surveyed with 100m dipoles, 50km with 300m dipoles, and 44km with 1km dipoles. The objectives of the Resistivity surveying were to detect and delineate regions of low Resistivity associated with fracturing, brines, high temperatures, and clay alteration. The Resistivity of rocks that are typical of hydrothermal environments is due to two main conduction mechanisms: (1) electrolytic conduction through pores and fractures; and (2) surface conduction due to a thin zone of cations attracted to those mineral surfaces with net negative charges (especially clay minerals). For saturated rocks, the Resistivity due to electrolytic conduction is a function of the effective porosity of the fractured rock, of the temperature, and of the salinity of the fluid filling the pores and fractures. The Resistivity decreases as the effective porosity, water saturation, salinity, and temperature increase. The presence of clay minerals and pyrite will also decrease the Resistivity Close

• 6. [Image] Dipole-Dipole Resistivity Survey of a Portion of the Coso Hot Springs KGRA, Inyo County, California

  	A detailed electrical resistivity survey of 54 line-km was completed at the Coso Hot Springs KGRA in September 1977. This survey has defined a bedrock resistivity low at least 4 sq mi (10 sq km) in extent ...
  	Citation × Citation Citation Abstract Copy Title: Dipole-Dipole Resistivity Survey of a Portion of the Coso Hot Springs KGRA, Inyo County, California Author: Fox, R.C. Year: 1978 A detailed electrical resistivity survey of 54 line-km was completed at the Coso Hot Springs KGRA in September 1977. This survey has defined a bedrock resistivity low at least 4 sq mi (10 sq km) in extent associated with the geothermal system at Coso. The boundaries of this low are generally well defined to the north and west but not as well to the south where an approximate southern limit has been determined. The bedrock resistivity low merges with an observed resistivity low over gravel fill east of Coso Hot Springs. A complex horizontal and vertical resistivity structure of the surveyed area has been defined which precludes the use of layered-earth or two-dimensional interpretive models for much of the surveyed area. In general the survey data indicate that a 10 to 20 ohm-meter zone extends from near surface to a depth greater than 750 meters within the geothermal system. This zone is bordered to the north and west by bedrock resistivities greater than 200 ohm-meters and to the south by bedrock resistivities greater than 50 ohm-meters. A combination of observed increases in: (1) fracture density (higher permeability), (2) alteration (high clay content), and (3) temperatures (higher dissolved solid content of ground water) within the bedrock low explain its presence Title: Dipole-Dipole Resistivity Survey of a Portion of the Coso Hot Springs KGRA, Inyo County, California Author: Fox, R.C. Year: 1978 A detailed electrical resistivity survey of 54 line-km was completed at the Coso Hot Springs KGRA in September 1977. This survey has defined a bedrock resistivity low at least 4 sq mi (10 sq km) in extent associated with the geothermal system at Coso. The boundaries of this low are generally well defined to the north and west but not as well to the south where an approximate southern limit has been determined. The bedrock resistivity low merges with an observed resistivity low over gravel fill east of Coso Hot Springs. A complex horizontal and vertical resistivity structure of the surveyed area has been defined which precludes the use of layered-earth or two-dimensional interpretive models for much of the surveyed area. In general the survey data indicate that a 10 to 20 ohm-meter zone extends from near surface to a depth greater than 750 meters within the geothermal system. This zone is bordered to the north and west by bedrock resistivities greater than 200 ohm-meters and to the south by bedrock resistivities greater than 50 ohm-meters. A combination of observed increases in: (1) fracture density (higher permeability), (2) alteration (high clay content), and (3) temperatures (higher dissolved solid content of ground water) within the bedrock low explain its presence Close

• 7. [Image] Initial Investigation of Soil Mercury Geochemistry as an Aid to Drill Site Selection in Geothermal Systems

  	A mercury-in-soil survey was conducted at the Roosevelt Hot Springs Known Geothermal Resource Area (KGRA), Utah, to evaluate mercury soil geochemistry as a method of selecting exploration well sites in ...
  	Citation × Citation Citation Abstract Copy Title: Initial Investigation of Soil Mercury Geochemistry as an Aid to Drill Site Selection in Geothermal Systems Author: Capuano, R.M. Year: 1978 A mercury-in-soil survey was conducted at the Roosevelt Hot Springs Known Geothermal Resource Area (KGRA), Utah, to evaluate mercury soil geochemistry as a method of selecting exploration well sites in a hot-water geothermal system. Samples of -80 mesh soil were collected at 30.5 m intervals along traverses crossing known structures, surficial geothermal alteration, and exploration well sites, and were analyzed using a Gold Film Mercury Detector. Strong mercury anomalies occur at locations along known structures in close proximity to subsurface thermal activity; examples include areas over hot spring deposits and near a shallow producing well. In contrast, background mercury concentrations are present in nearby locations with little or no indication of subsurface thermal activity, such as areas around deep marginal producing wells and dry wells, and areas lacking hot spring deposits. These results indicate that mercury geochemical surveys can be useful for identifying and mapping structures controlling fluid flow in geothermal systems and for delineating areas overlying near-surface thermal activity. Soil mercury geochemistry thus provides information which may aid in the cost-effective selection of exploratory well sites Title: Initial Investigation of Soil Mercury Geochemistry as an Aid to Drill Site Selection in Geothermal Systems Author: Capuano, R.M. Year: 1978 A mercury-in-soil survey was conducted at the Roosevelt Hot Springs Known Geothermal Resource Area (KGRA), Utah, to evaluate mercury soil geochemistry as a method of selecting exploration well sites in a hot-water geothermal system. Samples of -80 mesh soil were collected at 30.5 m intervals along traverses crossing known structures, surficial geothermal alteration, and exploration well sites, and were analyzed using a Gold Film Mercury Detector. Strong mercury anomalies occur at locations along known structures in close proximity to subsurface thermal activity; examples include areas over hot spring deposits and near a shallow producing well. In contrast, background mercury concentrations are present in nearby locations with little or no indication of subsurface thermal activity, such as areas around deep marginal producing wells and dry wells, and areas lacking hot spring deposits. These results indicate that mercury geochemical surveys can be useful for identifying and mapping structures controlling fluid flow in geothermal systems and for delineating areas overlying near-surface thermal activity. Soil mercury geochemistry thus provides information which may aid in the cost-effective selection of exploratory well sites Close