Search

Search Results

• 1. [Image] Low-Temperature Geothermal Potential of the Ojo Caliente Warm Springs Area, Northern New Mexico

  	A detailed geochemical investigation of 17 waters (thermal and cold, mineralized and dilute) was performed in the Ojo Caliente-La Madera area. Two types of thermomineral waters have separate and distinctive ...
  	Citation × Citation Citation Abstract Copy Title: Low-Temperature Geothermal Potential of the Ojo Caliente Warm Springs Area, Northern New Mexico Author: Vuataz, F.D. Year: 1984 A detailed geochemical investigation of 17 waters (thermal and cold, mineralized and dilute) was performed in the Ojo Caliente-La Madera area. Two types of thermomineral waters have separate and distinctive geologic, geochemical, and geothermal characteristics. The water from Ojo Caliente Resort emerges with temperatures less than or equal to 54/sup 0/C from a Precambrian metarhyolite. Its chemistry, typically Na-HCO/sub 3/, has a total mineralization of 3600 mg/l. Isotopic studies have shown that the thermal water emerges from the springs and a hot well without significant mixing with the cold shallow aquifer of the valley alluvium. However, the cold aquifer adjacent to the resort does contain varying amounts of thermal water that originates from the warm spring system. Geothermometry calculations indicate that the thermal water may be as hot as 85/sup 0/C at depth before its ascent toward surface. Thermodynamic computations on the reaction states of numerous mineral phases suggest that the thermal water will not cause major scaling problems if the hot water is utilized for direct-use geothermal applications. By means of a network of very shallow holes, temperature and electrical conductivity anomalies have been found elsewhere in the valley around Ojo Caliente, and resistivity soundings have confirmed the presence of a plume of thermal water entering the shallow aquifer. The group of lukewarm springs around La Madera, with temperatures less than or equal to 29/sup 0/C, chemical type of NaCaMg-HCO/sub 3/Cl and with a total mineralization less than or equal to 1500 mg/l behaves as a different system without any Apparent relation to the Ojo Caliente system. Its temperature at depth is not believed to exceed 35 to 40/sup 0/C Title: Low-Temperature Geothermal Potential of the Ojo Caliente Warm Springs Area, Northern New Mexico Author: Vuataz, F.D. Year: 1984 A detailed geochemical investigation of 17 waters (thermal and cold, mineralized and dilute) was performed in the Ojo Caliente-La Madera area. Two types of thermomineral waters have separate and distinctive geologic, geochemical, and geothermal characteristics. The water from Ojo Caliente Resort emerges with temperatures less than or equal to 54/sup 0/C from a Precambrian metarhyolite. Its chemistry, typically Na-HCO/sub 3/, has a total mineralization of 3600 mg/l. Isotopic studies have shown that the thermal water emerges from the springs and a hot well without significant mixing with the cold shallow aquifer of the valley alluvium. However, the cold aquifer adjacent to the resort does contain varying amounts of thermal water that originates from the warm spring system. Geothermometry calculations indicate that the thermal water may be as hot as 85/sup 0/C at depth before its ascent toward surface. Thermodynamic computations on the reaction states of numerous mineral phases suggest that the thermal water will not cause major scaling problems if the hot water is utilized for direct-use geothermal applications. By means of a network of very shallow holes, temperature and electrical conductivity anomalies have been found elsewhere in the valley around Ojo Caliente, and resistivity soundings have confirmed the presence of a plume of thermal water entering the shallow aquifer. The group of lukewarm springs around La Madera, with temperatures less than or equal to 29/sup 0/C, chemical type of NaCaMg-HCO/sub 3/Cl and with a total mineralization less than or equal to 1500 mg/l behaves as a different system without any Apparent relation to the Ojo Caliente system. Its temperature at depth is not believed to exceed 35 to 40/sup 0/C Close

• 2. [Image] Liquid-Fluidized-Bed Heat Exchanger Design Parameters

  	Liquid-fluidized-bed heat exchangers prevent scale accumulation on heat transfer surfaces and reduce the required heat transfer surface when scaling fluids, such as geothermal water, are used as the primary ...
  	Citation × Citation Citation Abstract Copy Title: Liquid-Fluidized-Bed Heat Exchanger Design Parameters Author: Allen, C.A. Year: 1978 Liquid-fluidized-bed heat exchangers prevent scale accumulation on heat transfer surfaces and reduce the required heat transfer surface when scaling fluids, such as geothermal water, are used as the primary or working fluid. Liquid-fluidized-bed heat exchangers, principles of operation, and design parameters are described. Horizontal and vertical assemblies are discussed, including problems encountered with both designs. Bed-side heat transfer coefficients are given for limited cases, and a correlation is provided for calculating heat transfer coefficients for horizontal assemblies. A design example for a 60 kW/sub (e)/ (60 kW/sub (electric)/ preheater is included Title: Liquid-Fluidized-Bed Heat Exchanger Design Parameters Author: Allen, C.A. Year: 1978 Liquid-fluidized-bed heat exchangers prevent scale accumulation on heat transfer surfaces and reduce the required heat transfer surface when scaling fluids, such as geothermal water, are used as the primary or working fluid. Liquid-fluidized-bed heat exchangers, principles of operation, and design parameters are described. Horizontal and vertical assemblies are discussed, including problems encountered with both designs. Bed-side heat transfer coefficients are given for limited cases, and a correlation is provided for calculating heat transfer coefficients for horizontal assemblies. A design example for a 60 kW/sub (e)/ (60 kW/sub (electric)/ preheater is included Close

• 3. [Image] Dipole-Dipole Resistivity Surveys, Roosevelt Hot Springs KGRA. Final Report, Volume 2

  	Dipole-dipole Resistivity surveys were conducted at Roosevelt Hot Springs KGRA. Three different dipole spacings were used; 99km of traverse line were surveyed with 100m dipoles, 50km with 300m dipoles, ...
  	Citation × Citation Citation Abstract Copy Title: Dipole-Dipole Resistivity Surveys, Roosevelt Hot Springs KGRA. Final Report, Volume 2 Author: Ward, S.H. Year: 1976 Dipole-dipole Resistivity surveys were conducted at Roosevelt Hot Springs KGRA. Three different dipole spacings were used; 99km of traverse line were surveyed with 100m dipoles, 50km with 300m dipoles, and 44km with 1km dipoles. The objectives of the Resistivity surveying were to detect and delineate regions of low Resistivity associated with fracturing, brines, high temperatures, and clay alteration. The Resistivity of rocks that are typical of hydrothermal environments is due to two main conduction mechanisms: (1) electrolytic conduction through pores and fractures; and (2) surface conduction due to a thin zone of cations attracted to those mineral surfaces with net negative charges (especially clay minerals). For saturated rocks, the Resistivity due to electrolytic conduction is a function of the effective porosity of the fractured rock, of the temperature, and of the salinity of the fluid filling the pores and fractures. The Resistivity decreases as the effective porosity, water saturation, salinity, and temperature increase. The presence of clay minerals and pyrite will also decrease the Resistivity Title: Dipole-Dipole Resistivity Surveys, Roosevelt Hot Springs KGRA. Final Report, Volume 2 Author: Ward, S.H. Year: 1976 Dipole-dipole Resistivity surveys were conducted at Roosevelt Hot Springs KGRA. Three different dipole spacings were used; 99km of traverse line were surveyed with 100m dipoles, 50km with 300m dipoles, and 44km with 1km dipoles. The objectives of the Resistivity surveying were to detect and delineate regions of low Resistivity associated with fracturing, brines, high temperatures, and clay alteration. The Resistivity of rocks that are typical of hydrothermal environments is due to two main conduction mechanisms: (1) electrolytic conduction through pores and fractures; and (2) surface conduction due to a thin zone of cations attracted to those mineral surfaces with net negative charges (especially clay minerals). For saturated rocks, the Resistivity due to electrolytic conduction is a function of the effective porosity of the fractured rock, of the temperature, and of the salinity of the fluid filling the pores and fractures. The Resistivity decreases as the effective porosity, water saturation, salinity, and temperature increase. The presence of clay minerals and pyrite will also decrease the Resistivity Close

• 4. [Image] Geologic Interpretation of the Geothermal Potential of the North Bonneville Area

  	Possible geothermal development for the township of North Bonneville, Washington is being investigated because of the proximity of the town to hot springs in a geologic province of good geothermal potential. ...
  	Citation × Citation Citation Abstract Copy Title: Geologic Interpretation of the Geothermal Potential of the North Bonneville Area Author: Nielson, D.L. Year: 1980 Possible geothermal development for the township of North Bonneville, Washington is being investigated because of the proximity of the town to hot springs in a geologic province of good geothermal potential. Surface expression of geothermal resources is provided by conduits through an impermeable reservoir cap and is therefore generally structurally controlled. Near North Bonneville the geologic formations that underlie potential drilling sites are the Eagle Creek formation and the Ohanpecosh Formation. The Lower Miocene Eagle Creek Formation is composed of poorly consolidated volcanic conglomerates, sandstOnes, tuffs, and includes a few minor interbedded lava flows. The Eocene-Oligiocene Ohanapecosh (Weigle) Formation in its nearest exposures to North Bonneville is composed of Volcaniclastics and lava flows. The Ohanapecosh has been altered to zeolites and clays and is therefore Well consolidated and impermeable. The lack of permeability provides the necessary reservoir cap for any geothermal system that may be present at depth. This formation, to the northeast, in the Wind River drainage is greater than 19,000 ft. thick. Circulation of geothermal heated water from this thick sequence of impermeable strata must be associated with penetrating fracture zones Title: Geologic Interpretation of the Geothermal Potential of the North Bonneville Area Author: Nielson, D.L. Year: 1980 Possible geothermal development for the township of North Bonneville, Washington is being investigated because of the proximity of the town to hot springs in a geologic province of good geothermal potential. Surface expression of geothermal resources is provided by conduits through an impermeable reservoir cap and is therefore generally structurally controlled. Near North Bonneville the geologic formations that underlie potential drilling sites are the Eagle Creek formation and the Ohanpecosh Formation. The Lower Miocene Eagle Creek Formation is composed of poorly consolidated volcanic conglomerates, sandstOnes, tuffs, and includes a few minor interbedded lava flows. The Eocene-Oligiocene Ohanapecosh (Weigle) Formation in its nearest exposures to North Bonneville is composed of Volcaniclastics and lava flows. The Ohanapecosh has been altered to zeolites and clays and is therefore Well consolidated and impermeable. The lack of permeability provides the necessary reservoir cap for any geothermal system that may be present at depth. This formation, to the northeast, in the Wind River drainage is greater than 19,000 ft. thick. Circulation of geothermal heated water from this thick sequence of impermeable strata must be associated with penetrating fracture zones Close

• 5. [Image] Initial Investigation of Soil Mercury Geochemistry as an Aid to Drill Site Selection in Geothermal Systems

  	A mercury-in-soil survey was conducted at the Roosevelt Hot Springs Known Geothermal Resource Area (KGRA), Utah, to evaluate mercury soil geochemistry as a method of selecting exploration well sites in ...
  	Citation × Citation Citation Abstract Copy Title: Initial Investigation of Soil Mercury Geochemistry as an Aid to Drill Site Selection in Geothermal Systems Author: Capuano, R.M. Year: 1978 A mercury-in-soil survey was conducted at the Roosevelt Hot Springs Known Geothermal Resource Area (KGRA), Utah, to evaluate mercury soil geochemistry as a method of selecting exploration well sites in a hot-water geothermal system. Samples of -80 mesh soil were collected at 30.5 m intervals along traverses crossing known structures, surficial geothermal alteration, and exploration well sites, and were analyzed using a Gold Film Mercury Detector. Strong mercury anomalies occur at locations along known structures in close proximity to subsurface thermal activity; examples include areas over hot spring deposits and near a shallow producing well. In contrast, background mercury concentrations are present in nearby locations with little or no indication of subsurface thermal activity, such as areas around deep marginal producing wells and dry wells, and areas lacking hot spring deposits. These results indicate that mercury geochemical surveys can be useful for identifying and mapping structures controlling fluid flow in geothermal systems and for delineating areas overlying near-surface thermal activity. Soil mercury geochemistry thus provides information which may aid in the cost-effective selection of exploratory well sites Title: Initial Investigation of Soil Mercury Geochemistry as an Aid to Drill Site Selection in Geothermal Systems Author: Capuano, R.M. Year: 1978 A mercury-in-soil survey was conducted at the Roosevelt Hot Springs Known Geothermal Resource Area (KGRA), Utah, to evaluate mercury soil geochemistry as a method of selecting exploration well sites in a hot-water geothermal system. Samples of -80 mesh soil were collected at 30.5 m intervals along traverses crossing known structures, surficial geothermal alteration, and exploration well sites, and were analyzed using a Gold Film Mercury Detector. Strong mercury anomalies occur at locations along known structures in close proximity to subsurface thermal activity; examples include areas over hot spring deposits and near a shallow producing well. In contrast, background mercury concentrations are present in nearby locations with little or no indication of subsurface thermal activity, such as areas around deep marginal producing wells and dry wells, and areas lacking hot spring deposits. These results indicate that mercury geochemical surveys can be useful for identifying and mapping structures controlling fluid flow in geothermal systems and for delineating areas overlying near-surface thermal activity. Soil mercury geochemistry thus provides information which may aid in the cost-effective selection of exploratory well sites Close

• 6. [Image] Evaluation and Targeting of Geothermal Energy Resources in the Southeastern United States. Progress Report, May 1, 1976--October 31, 1976

  	Progress is reported in the development of procedures for the evaluation of low-temperature radiogenically-derived geothermal resources in the eastern United States utilizing geological geochemical, and ...
  	Citation × Citation Citation Abstract Copy Title: Evaluation and Targeting of Geothermal Energy Resources in the Southeastern United States. Progress Report, May 1, 1976--October 31, 1976 Author: Costain, J.K. Year: 1976 Progress is reported in the development of procedures for the evaluation of low-temperature radiogenically-derived geothermal resources in the eastern United States utilizing geological geochemical, and geophysical data. An optimum site for geothermal development in the tectonically stable eastern United States will probably be associated with crustal igneous rocks containing relatively high concentrations of radiogenic heat-producing elements buried beneath an insulating blanket of sediments of low thermal conductivity. Evaluation of plutonic rocks exposed in the Piedmont will aid in the interpretation of gravity and magnetic data for the Atlantic Coastal Plain. Initial results of determination of heat generation from surface samples in South Caroline are encouraging, especially if granitic igneous rocks of similar heat generation can be found beneath sedimentary insulation. Continues logging of existing wells in Coastal Plain sediments supports earlier conclusion that these sediments do behave as efficient sedimentary insulators. Higher temperatures appear to be reached at shallower depths for wells drilled in Coastal Plain sediments in the vicinity of the Georgetown, South Carolina gravity law. Detailed structural mapping in the vicinity of the warm springs in northwestern Virginia has confirmed structural control of the warm springs, and has revealed the existence of kink bands. The kink bands could be related to the development of zones of vertical permeability which serve as conduits in sedimentary rocks for ascending hot water. Title: Evaluation and Targeting of Geothermal Energy Resources in the Southeastern United States. Progress Report, May 1, 1976--October 31, 1976 Author: Costain, J.K. Year: 1976 Progress is reported in the development of procedures for the evaluation of low-temperature radiogenically-derived geothermal resources in the eastern United States utilizing geological geochemical, and geophysical data. An optimum site for geothermal development in the tectonically stable eastern United States will probably be associated with crustal igneous rocks containing relatively high concentrations of radiogenic heat-producing elements buried beneath an insulating blanket of sediments of low thermal conductivity. Evaluation of plutonic rocks exposed in the Piedmont will aid in the interpretation of gravity and magnetic data for the Atlantic Coastal Plain. Initial results of determination of heat generation from surface samples in South Caroline are encouraging, especially if granitic igneous rocks of similar heat generation can be found beneath sedimentary insulation. Continues logging of existing wells in Coastal Plain sediments supports earlier conclusion that these sediments do behave as efficient sedimentary insulators. Higher temperatures appear to be reached at shallower depths for wells drilled in Coastal Plain sediments in the vicinity of the Georgetown, South Carolina gravity law. Detailed structural mapping in the vicinity of the warm springs in northwestern Virginia has confirmed structural control of the warm springs, and has revealed the existence of kink bands. The kink bands could be related to the development of zones of vertical permeability which serve as conduits in sedimentary rocks for ascending hot water. Close