Search

Search Results

• 31. [Image] Geothermal Progress Monitor: Report No. 17, December 1995

  	DOE is particularly concerned with reducing the costs of geothermal power generation, especially with the abundant moderate to low-temperature resources in the US. This concern is reflected in DOE`s support ...
  	Citation × Citation Citation Abstract Copy Title: Geothermal Progress Monitor: Report No. 17, December 1995 Author: Assistant Secretary for Energy and Efficiency and Renewable Energy, Geothermal Division Year: 1995 DOE is particularly concerned with reducing the costs of geothermal power generation, especially with the abundant moderate to low-temperature resources in the US. This concern is reflected in DOE`s support of a number of energy conversion projects. Projects which focus on the costs and performance of binary cycle technology include a commercial demonstration of supersaturated turbine expansions, which earlier Studies have indicated could increase the power produced per pound of fluid. Other binary cycle projects include evaluations of the performance of various working fluid mixtures and the development and testing of advanced heat rejection systems which are desperately needed in water-short geothermal areas. DOE is also investigating the applicability of flash steam technology to low-temperature resources, as an economic alternative to binary cycle systems. A low-cost, low-pressure steam turbine, selected for a grant, will be constructed to utilize fluid discharged from a flash steam plant in Nevada. Another project addresses the efficiency of high-temperature flash plants with a demonstration of the performance of the Biphase turbine which may increase the power output of such installations with no increase in fluid flow. Perhaps the most noteworthy feature of this issue of the GPM, the 17th since its inception in 1980, is the high degree of industry participation in federally-sponsored geothermal research and development. This report describes geothermal development activities Title: Geothermal Progress Monitor: Report No. 17, December 1995 Author: Assistant Secretary for Energy and Efficiency and Renewable Energy, Geothermal Division Year: 1995 DOE is particularly concerned with reducing the costs of geothermal power generation, especially with the abundant moderate to low-temperature resources in the US. This concern is reflected in DOE`s support of a number of energy conversion projects. Projects which focus on the costs and performance of binary cycle technology include a commercial demonstration of supersaturated turbine expansions, which earlier Studies have indicated could increase the power produced per pound of fluid. Other binary cycle projects include evaluations of the performance of various working fluid mixtures and the development and testing of advanced heat rejection systems which are desperately needed in water-short geothermal areas. DOE is also investigating the applicability of flash steam technology to low-temperature resources, as an economic alternative to binary cycle systems. A low-cost, low-pressure steam turbine, selected for a grant, will be constructed to utilize fluid discharged from a flash steam plant in Nevada. Another project addresses the efficiency of high-temperature flash plants with a demonstration of the performance of the Biphase turbine which may increase the power output of such installations with no increase in fluid flow. Perhaps the most noteworthy feature of this issue of the GPM, the 17th since its inception in 1980, is the high degree of industry participation in federally-sponsored geothermal research and development. This report describes geothermal development activities Close

• 32. [Image] Development of drilling foams for geothermal applications

  	The use of foam drilling fluids in geothermal applications is addressed. A description of foams - what they are, how they are used, their properties, equipment required to use them, the advantages and ...
  	Citation × Citation Citation Abstract Copy Title: Development of drilling foams for geothermal applications Author: McDonald, W.J. Year: 1980 The use of foam drilling fluids in geothermal applications is addressed. A description of foams - what they are, how they are used, their properties, equipment required to use them, the advantages and disadvantages of foams, etc. - is presented. Geothermal applications are discussed. Results of industry interviews presented indicate significant potential for foams, but also indicate significant technical problems to be solved to achieve this potential. Testing procedures and results of tests on representative foams provide a basis for work to develop high-temperature foams; SAND-79-7122 Title: Development of drilling foams for geothermal applications Author: McDonald, W.J. Year: 1980 The use of foam drilling fluids in geothermal applications is addressed. A description of foams - what they are, how they are used, their properties, equipment required to use them, the advantages and disadvantages of foams, etc. - is presented. Geothermal applications are discussed. Results of industry interviews presented indicate significant potential for foams, but also indicate significant technical problems to be solved to achieve this potential. Testing procedures and results of tests on representative foams provide a basis for work to develop high-temperature foams; SAND-79-7122 Close

• 33. [Image] Subsurface investigations at the Roosevelt KGRA, Utah. Final report

  	An investigation of the geothermal reservoir in the Roosevelt Hot Springs Known Geothermal Resource Area in Utah was carried out. The objective of this effort was to develop predictions for well production ...
  	Citation × Citation Citation Abstract Copy Title: Subsurface investigations at the Roosevelt KGRA, Utah. Final report Author: Butz, J. Year: 1979 An investigation of the geothermal reservoir in the Roosevelt Hot Springs Known Geothermal Resource Area in Utah was carried out. The objective of this effort was to develop predictions for well production capacities, based on data taken during field tests and through use of a computer model. In turn, the production information could then be used in design optimization and economic analyses for development of the resource under study. Flow tests of a geothermal well, Utah State 14-2, were conducted. Data consisting of pressure and temperature logs as a function of depth were obtained. Maximum recorded temperature was 503/sup 0/F (262/sup 0/C) and maximum pressure, 954 psia (6.58MPa) as measured under flow conditions. Tests were run at rates up to 580,000 lb/hr (73.3 kg/sec) total flow. The information gathered during the testing was reduced and compared to results of a predictive computer model. Reservoir conditions in the Roosevelt Hot Springs KGRA are such that two-phase flow exists in the wellbore and, in some cases, also in the reservoir itself. The computer model employed in the analysis reflects current efforts to improve the state-of-the-art in the prediction of two-phase pressure drops in vertical systems. Predictions at flowrates of up to 300,000 lb/hr (38 kg/sec) matched quite well with test data, while modeling at higher flowrates (to maximum tested) showed progressively greater deviation from test data. Cause of the observed degradation is postulated to be the movement of the flash horizon into the reservoir, due to drawdown at high flowrates; DOE/ET/28389-1 Title: Subsurface investigations at the Roosevelt KGRA, Utah. Final report Author: Butz, J. Year: 1979 An investigation of the geothermal reservoir in the Roosevelt Hot Springs Known Geothermal Resource Area in Utah was carried out. The objective of this effort was to develop predictions for well production capacities, based on data taken during field tests and through use of a computer model. In turn, the production information could then be used in design optimization and economic analyses for development of the resource under study. Flow tests of a geothermal well, Utah State 14-2, were conducted. Data consisting of pressure and temperature logs as a function of depth were obtained. Maximum recorded temperature was 503/sup 0/F (262/sup 0/C) and maximum pressure, 954 psia (6.58MPa) as measured under flow conditions. Tests were run at rates up to 580,000 lb/hr (73.3 kg/sec) total flow. The information gathered during the testing was reduced and compared to results of a predictive computer model. Reservoir conditions in the Roosevelt Hot Springs KGRA are such that two-phase flow exists in the wellbore and, in some cases, also in the reservoir itself. The computer model employed in the analysis reflects current efforts to improve the state-of-the-art in the prediction of two-phase pressure drops in vertical systems. Predictions at flowrates of up to 300,000 lb/hr (38 kg/sec) matched quite well with test data, while modeling at higher flowrates (to maximum tested) showed progressively greater deviation from test data. Cause of the observed degradation is postulated to be the movement of the flash horizon into the reservoir, due to drawdown at high flowrates; DOE/ET/28389-1 Close

• 34. [Image] Hot Dry Rock Geothermal Energy Development Program. Annual Report, Fiscal Year 1983

  	Emphasis was on hydraulic-fracturing experiments at depths around 3.5 km (11,473 ft) in the two inclined wells of the Phase II system at Fenton Hill, New Mexico; on improved facilities and techniques for ...
  	Citation × Citation Citation Abstract Copy Title: Hot Dry Rock Geothermal Energy Development Program. Annual Report, Fiscal Year 1983 Author: Smith, M.C. (comp.) Year: 1985 Emphasis was on hydraulic-fracturing experiments at depths around 3.5 km (11,473 ft) in the two inclined wells of the Phase II system at Fenton Hill, New Mexico; on improved facilities and techniques for mapping the source locations of acoustic signals generated by the fracturing events; on mathematical modeling of the fracture systems produced in these and earlier experiments; and on development of a family of slimline high-temperature downhole instruments that can be used within or through relatively small-diameter pressure tubing. Hydraulic fracturing at a vertical depth of approximately 3500 m (11,500 ft) in well EE-2, the deeper well, produced fractures that, in acoustic maps, appear to occupy a large, roughly ellipsoidal volume whose major axis is directed to the north of the other well, EE-3. Hydraulic fracturing from EE-3 at a similar depth produced another set of fractures that appear to be approximately parallel to and centered about 180 m (600 ft) east of the earlier set. Subsequent fluid injections reduced the distance between the two sets, but no hydraulic connection between them was established. Modeling the silica concentrations of fluid circulated through the earlier Phase I system indicates that this type of permeation also contributes significantly to heat extraction during system operation. The precision and accuracy of locating the sources of acoustic signals detected during hydraulic-fracturing operations have been increased by improvements in equipment, drilling of another deep hole for geophone emplacement, and additional station calibrations. Analysis of the signals has also been improved and broadened. Development of slimline downhole instruments has included a detonator tool, a geophone package, and final design of a high-temperature borehole acoustic televiewer. A crosswell acoustic transceiver has also been developed for investigating rock type and structure between wellbores. 32 refs., 35 figs. Title: Hot Dry Rock Geothermal Energy Development Program. Annual Report, Fiscal Year 1983 Author: Smith, M.C. (comp.) Year: 1985 Emphasis was on hydraulic-fracturing experiments at depths around 3.5 km (11,473 ft) in the two inclined wells of the Phase II system at Fenton Hill, New Mexico; on improved facilities and techniques for mapping the source locations of acoustic signals generated by the fracturing events; on mathematical modeling of the fracture systems produced in these and earlier experiments; and on development of a family of slimline high-temperature downhole instruments that can be used within or through relatively small-diameter pressure tubing. Hydraulic fracturing at a vertical depth of approximately 3500 m (11,500 ft) in well EE-2, the deeper well, produced fractures that, in acoustic maps, appear to occupy a large, roughly ellipsoidal volume whose major axis is directed to the north of the other well, EE-3. Hydraulic fracturing from EE-3 at a similar depth produced another set of fractures that appear to be approximately parallel to and centered about 180 m (600 ft) east of the earlier set. Subsequent fluid injections reduced the distance between the two sets, but no hydraulic connection between them was established. Modeling the silica concentrations of fluid circulated through the earlier Phase I system indicates that this type of permeation also contributes significantly to heat extraction during system operation. The precision and accuracy of locating the sources of acoustic signals detected during hydraulic-fracturing operations have been increased by improvements in equipment, drilling of another deep hole for geophone emplacement, and additional station calibrations. Analysis of the signals has also been improved and broadened. Development of slimline downhole instruments has included a detonator tool, a geophone package, and final design of a high-temperature borehole acoustic televiewer. A crosswell acoustic transceiver has also been developed for investigating rock type and structure between wellbores. 32 refs., 35 figs. Close

• 35. [Image] Geothermal Reservoir Categorization and Stimulation Study

  	Analyses of the fraction of geothermal wells that are dry (dry-hole fraction) indicate that geothermal reservoirs can be fitted into four basic categories: (i) Quaternary to late Tertiary sediments (almost ...
  	Citation × Citation Citation Abstract Copy Title: Geothermal Reservoir Categorization and Stimulation Study Author: Overton, H.L. Year: 1977 Analyses of the fraction of geothermal wells that are dry (dry-hole fraction) indicate that geothermal reservoirs can be fitted into four basic categories: (i) Quaternary to late Tertiary sediments (almost no dry holes); (ii) Quaternary to late Tertiary extrusives (approximately 20 percent dry holes); (iii) Mesozoic or older metamorphic rocks (approximately 25-30 percent dry holes); and (iv) Precambrian or younger rocks (data limited to Roosevelt Springs where 33 percent of the wells were dry). Failure of geothermal wells to flow economically is due mainly to low-permeability formations in unfractured regions. Generally the permeability correlates inversely with the temperature-age product and directly with the original rock porosity and pore size. However, this correlation fails whenever high-stress fields provide vertical fracturing or faulting, and it is the high-stress/low-permeability category that is most amenable to artificial stimulation by hydraulic fracturing, propellant fracturing, or chemical explosive fracturing. Category (i) geothermal fields (e.g., Cerro Prieto, Mexico; Niland, CA; East Mesa, CA) are not recommended for artificial stimulation because these younger sediments almost always produce warm or hot water. Most geothermal fields fit into category (ii) (e.g., Wairakei, New Zealand; Matsukawa, Japan; Ahuachapan, El Salvador) and in the case of Mt. Home, ID, and Chandler, AZ, possess some potential for stimulation. The Geysers is a category (iii) field, and its highly stressed brittle rocks should make this site amenable to stimulation by explosive fracturing techniques. Roosevelt Springs, UT, Well 9-1 is in category (iv) and is a flow failure. It represents a prime candidate for stimulation by hydraulic fracturing because it has a measured temperature of 227/sup 0/C, is cased and available for experimentation, and is within 900 m of an excellent geothermal producing well Title: Geothermal Reservoir Categorization and Stimulation Study Author: Overton, H.L. Year: 1977 Analyses of the fraction of geothermal wells that are dry (dry-hole fraction) indicate that geothermal reservoirs can be fitted into four basic categories: (i) Quaternary to late Tertiary sediments (almost no dry holes); (ii) Quaternary to late Tertiary extrusives (approximately 20 percent dry holes); (iii) Mesozoic or older metamorphic rocks (approximately 25-30 percent dry holes); and (iv) Precambrian or younger rocks (data limited to Roosevelt Springs where 33 percent of the wells were dry). Failure of geothermal wells to flow economically is due mainly to low-permeability formations in unfractured regions. Generally the permeability correlates inversely with the temperature-age product and directly with the original rock porosity and pore size. However, this correlation fails whenever high-stress fields provide vertical fracturing or faulting, and it is the high-stress/low-permeability category that is most amenable to artificial stimulation by hydraulic fracturing, propellant fracturing, or chemical explosive fracturing. Category (i) geothermal fields (e.g., Cerro Prieto, Mexico; Niland, CA; East Mesa, CA) are not recommended for artificial stimulation because these younger sediments almost always produce warm or hot water. Most geothermal fields fit into category (ii) (e.g., Wairakei, New Zealand; Matsukawa, Japan; Ahuachapan, El Salvador) and in the case of Mt. Home, ID, and Chandler, AZ, possess some potential for stimulation. The Geysers is a category (iii) field, and its highly stressed brittle rocks should make this site amenable to stimulation by explosive fracturing techniques. Roosevelt Springs, UT, Well 9-1 is in category (iv) and is a flow failure. It represents a prime candidate for stimulation by hydraulic fracturing because it has a measured temperature of 227/sup 0/C, is cased and available for experimentation, and is within 900 m of an excellent geothermal producing well Close

• 36. [Image] Drilling plan: Raft River Geothermal Exploratory Hole No. 3

  	The program, plans, and procedures to be used in drilling and completion of the Raft River Geothermal Exploratory Hole No. 3(RRGE-3) are described. RRGE-3 will be located in the Raft River valley of south ...
  	Citation × Citation Citation Abstract Copy Title: Drilling plan: Raft River Geothermal Exploratory Hole No. 3 Author: Industrial Applications Division , Nevada Operations Office Year: 1976 The program, plans, and procedures to be used in drilling and completion of the Raft River Geothermal Exploratory Hole No. 3(RRGE-3) are described. RRGE-3 will be located in the Raft River valley of south central Idaho, southeast of Burley, and approximately 16 miles south of Malta, Idaho. The third exploratory hole will be drilled to provide data to further investigate and evaluate the geothermal reservoir, as well as to optimize the location of possible future resource and/or injection wells, and to develop methods to reduce the cost of geothermal wells. Plans call for drilling to a total depth of approximately 6,000 ft., or to the depth at which it is either indicated from temperature and test flow data and from logs that an acceptable hot water resource is available or that the hole is accepted as a possible reinjection well. (LBS) Title: Drilling plan: Raft River Geothermal Exploratory Hole No. 3 Author: Industrial Applications Division , Nevada Operations Office Year: 1976 The program, plans, and procedures to be used in drilling and completion of the Raft River Geothermal Exploratory Hole No. 3(RRGE-3) are described. RRGE-3 will be located in the Raft River valley of south central Idaho, southeast of Burley, and approximately 16 miles south of Malta, Idaho. The third exploratory hole will be drilled to provide data to further investigate and evaluate the geothermal reservoir, as well as to optimize the location of possible future resource and/or injection wells, and to develop methods to reduce the cost of geothermal wells. Plans call for drilling to a total depth of approximately 6,000 ft., or to the depth at which it is either indicated from temperature and test flow data and from logs that an acceptable hot water resource is available or that the hole is accepted as a possible reinjection well. (LBS) Close

• 37. [Image] Geothermal Resource and Reservoir Investigations of U. S. Bureau of Reclamation Leaseholds at East Mesa, Imperial Valley, California

  	The study included five parts: geology, seismicity, well testing, reservoir simulation, and geochemistry. Included in appendices are: production test data and discussion, interference tests, production ...
  	Citation × Citation Citation Abstract Copy Title: Geothermal Resource and Reservoir Investigations of U. S. Bureau of Reclamation Leaseholds at East Mesa, Imperial Valley, California Author: Howard, J. Year: 1978 The study included five parts: geology, seismicity, well testing, reservoir simulation, and geochemistry. Included in appendices are: production test data and discussion, interference tests, production tests in the northern portion of the East Mesa KGRA, conversion tables, chemical analysis of fluids from East Mesa wells, and results of laboratory studies of scale samples taken from the vertical tube evaporator. (MHR) Title: Geothermal Resource and Reservoir Investigations of U. S. Bureau of Reclamation Leaseholds at East Mesa, Imperial Valley, California Author: Howard, J. Year: 1978 The study included five parts: geology, seismicity, well testing, reservoir simulation, and geochemistry. Included in appendices are: production test data and discussion, interference tests, production tests in the northern portion of the East Mesa KGRA, conversion tables, chemical analysis of fluids from East Mesa wells, and results of laboratory studies of scale samples taken from the vertical tube evaporator. (MHR) Close

• 38. [Image] Transient well testing in two-phase geothermal reservoirs

  	A study of well test analysis techniques in two-phase geothermal reservoirs has been conducted using a three-dimensional, two-phase, wellbore and reservoir simulation model. Well tests from Cerro Prieto ...
  	Citation × Citation Citation Abstract Copy Title: Transient well testing in two-phase geothermal reservoirs Author: Aydelotte, S.R. Year: 1980 A study of well test analysis techniques in two-phase geothermal reservoirs has been conducted using a three-dimensional, two-phase, wellbore and reservoir simulation model. Well tests from Cerro Prieto and the Hawaiian Geothermal project have been history matched. Using these well tests as a base, the influence of reservoir permeability, porosity, thickness, and heat capacity, along with flow rate and fracturing were studied. Single and two-phase transient well test equations were used to analyze these tests with poor results due to rapidly changing fluid properties and inability to calculate the flowing steam saturation in the reservoir. The injection of cold water into the reservoir does give good data from which formation properties can be calculated. Title: Transient well testing in two-phase geothermal reservoirs Author: Aydelotte, S.R. Year: 1980 A study of well test analysis techniques in two-phase geothermal reservoirs has been conducted using a three-dimensional, two-phase, wellbore and reservoir simulation model. Well tests from Cerro Prieto and the Hawaiian Geothermal project have been history matched. Using these well tests as a base, the influence of reservoir permeability, porosity, thickness, and heat capacity, along with flow rate and fracturing were studied. Single and two-phase transient well test equations were used to analyze these tests with poor results due to rapidly changing fluid properties and inability to calculate the flowing steam saturation in the reservoir. The injection of cold water into the reservoir does give good data from which formation properties can be calculated. Close

• 39. [Image] Industrial application of geothermal energy in Southeast Idaho

  	Those phosphate related and food processing industries in Southeastern Idaho are identified which require large energy inputs and the potential for direct application of geothermal energy is assessed. ...
  	Citation × Citation Citation Abstract Copy Title: Industrial application of geothermal energy in Southeast Idaho Author: Batdorf, J.A. Year: 1980 Those phosphate related and food processing industries in Southeastern Idaho are identified which require large energy inputs and the potential for direct application of geothermal energy is assessed. The total energy demand is given along with that fractional demand that can be satisfied by a geothermal source of known temperature. The potential for geothermal resource development is analyzed by examining the location of known thermal springs and wells, the location of state and federal geothermal exploration leases, and the location of federal and state oil and gas leasing activity in Southeast Idaho. Information is also presented regarding the location of geothermal, oil, and gas exploration wells in Southeast Idaho. The location of state and federal phosphate mining leases is also presented. This information is presented in table and map formats to show the proximity of exploration and development activities to current food and phosphate processing facilities and phosphate mining activities. (MHR); DOE/ID/12010-4 Title: Industrial application of geothermal energy in Southeast Idaho Author: Batdorf, J.A. Year: 1980 Those phosphate related and food processing industries in Southeastern Idaho are identified which require large energy inputs and the potential for direct application of geothermal energy is assessed. The total energy demand is given along with that fractional demand that can be satisfied by a geothermal source of known temperature. The potential for geothermal resource development is analyzed by examining the location of known thermal springs and wells, the location of state and federal geothermal exploration leases, and the location of federal and state oil and gas leasing activity in Southeast Idaho. Information is also presented regarding the location of geothermal, oil, and gas exploration wells in Southeast Idaho. The location of state and federal phosphate mining leases is also presented. This information is presented in table and map formats to show the proximity of exploration and development activities to current food and phosphate processing facilities and phosphate mining activities. (MHR); DOE/ID/12010-4 Close

• 40. [Image] Geology, hydrothermal petrology, stable isotope geochemistry, and fluid inclusion geothermometry of LASL geothermal test well C/T-1 (Mesa 31-1), East Mesa, Imperial Valley, California, USA

  	Borehole Mesa 31-1 (LASL C/T-1) is an 1899-m (6231-ft) deep well located in the northwestern part of the East Mesa Geothermal Field. Mesa 31-1 is the first Calibration/Test Well (C/T-1) in the Los Alamos ...
  	Citation × Citation Citation Abstract Copy Title: Geology, hydrothermal petrology, stable isotope geochemistry, and fluid inclusion geothermometry of LASL geothermal test well C/T-1 (Mesa 31-1), East Mesa, Imperial Valley, California, USA Author: Miller, K.R Year: 1980 Borehole Mesa 31-1 (LASL C/T-1) is an 1899-m (6231-ft) deep well located in the northwestern part of the East Mesa Geothermal Field. Mesa 31-1 is the first Calibration/Test Well (C/T-1) in the Los Alamos Scientific Laboratory (LASL), Geothermal Log Interpretation Program. The purpose of this study is to provide a compilation of drillhole data, drill cuttings, well lithology, and formation petrology that will serve to support the use of well LASL C/T-1 as a calibration/test well for geothermal logging. In addition, reviews of fluid chemistry, stable isotope studies, isotopic and fluid inclusion geothermometry, and the temperature log data are presented. This study provides the basic data on the geology and hydrothermal alteration of the rocks in LASL C/T-1 as background for the interpretation of wireline logs.; LA-8515-MS Title: Geology, hydrothermal petrology, stable isotope geochemistry, and fluid inclusion geothermometry of LASL geothermal test well C/T-1 (Mesa 31-1), East Mesa, Imperial Valley, California, USA Author: Miller, K.R Year: 1980 Borehole Mesa 31-1 (LASL C/T-1) is an 1899-m (6231-ft) deep well located in the northwestern part of the East Mesa Geothermal Field. Mesa 31-1 is the first Calibration/Test Well (C/T-1) in the Los Alamos Scientific Laboratory (LASL), Geothermal Log Interpretation Program. The purpose of this study is to provide a compilation of drillhole data, drill cuttings, well lithology, and formation petrology that will serve to support the use of well LASL C/T-1 as a calibration/test well for geothermal logging. In addition, reviews of fluid chemistry, stable isotope studies, isotopic and fluid inclusion geothermometry, and the temperature log data are presented. This study provides the basic data on the geology and hydrothermal alteration of the rocks in LASL C/T-1 as background for the interpretation of wireline logs.; LA-8515-MS Close