Search

Search Results

• 1. [Article] Environmental Durability of Reinforced Concrete Deck Girders Strengthened for Shear with Surface Bonded Carbon Fiber-Reinforced Polymer

  This research investigated the durability of carbon fiber-reinforced polymer composites (CFRP) used for shear strengthening reinforced concrete deck girders. Large beams were used to avoid accounting for ...

  Citation × Citation Citation Abstract Copy Title: Environmental Durability of Reinforced Concrete Deck Girders Strengthened for Shear with Surface Bonded Carbon Fiber-Reinforced Polymer Author: Higgins, Christopher, Dawson, Matthew R., Mitchell, Mikal M., Sopal, Gautam, Senturk, A. Ekin Year: 2009 This research investigated the durability of carbon fiber-reinforced polymer composites (CFRP) used for shear strengthening reinforced concrete deck girders. Large beams were used to avoid accounting for size effects in the data analysis. The effort included determining the role of freeze-thaw, moisture, and fatigue on structural performance and developing analytical design procedures that account for durability. The results showed that moisture infiltration behind the CFRP, combined with freeze-thaw, was critical in reducing shear panel stiffness and shear capacity. Long-term moisture exposure alone produced only a minor decrease in shear capacity. Freeze-thaw, combined with fatigue, had little effect on shear capacity if water infiltration was minimized. Fatigue caused some debonding, but the debonding was not significant enough to affect capacity. Use of ACI-318 with ACI 440 provided conservative predicted shear strengths after environmental exposure. However, the ACI approach did not provide uniform levels of safety because the observed conservatism was built into the prediction for the unstrengthened base specimens but not for the CFRP contribution. Consequently, a recommendation of the research is to apply the environmental exposure factor at the final design step to limit the effective CFRP stress/strain. For locations with very large numbers of wet freeze-thaw cycles and extended exposure to continuous moisture, the environmental reduction factors should be reduced even further. To better predict the CFRP bond strength demands that can occur due to shear-moment interaction, a further check of the design should be made beyond those required by ACI-440. Title: Environmental Durability of Reinforced Concrete Deck Girders Strengthened for Shear with Surface Bonded Carbon Fiber-Reinforced Polymer Author: Higgins, Christopher, Dawson, Matthew R., Mitchell, Mikal M., Sopal, Gautam, Senturk, A. Ekin Year: 2009 This research investigated the durability of carbon fiber-reinforced polymer composites (CFRP) used for shear strengthening reinforced concrete deck girders. Large beams were used to avoid accounting for size effects in the data analysis. The effort included determining the role of freeze-thaw, moisture, and fatigue on structural performance and developing analytical design procedures that account for durability. The results showed that moisture infiltration behind the CFRP, combined with freeze-thaw, was critical in reducing shear panel stiffness and shear capacity. Long-term moisture exposure alone produced only a minor decrease in shear capacity. Freeze-thaw, combined with fatigue, had little effect on shear capacity if water infiltration was minimized. Fatigue caused some debonding, but the debonding was not significant enough to affect capacity. Use of ACI-318 with ACI 440 provided conservative predicted shear strengths after environmental exposure. However, the ACI approach did not provide uniform levels of safety because the observed conservatism was built into the prediction for the unstrengthened base specimens but not for the CFRP contribution. Consequently, a recommendation of the research is to apply the environmental exposure factor at the final design step to limit the effective CFRP stress/strain. For locations with very large numbers of wet freeze-thaw cycles and extended exposure to continuous moisture, the environmental reduction factors should be reduced even further. To better predict the CFRP bond strength demands that can occur due to shear-moment interaction, a further check of the design should be made beyond those required by ACI-440. Close

• 2. [Article] Value of Travel Time Reliability Part II: A Study of Tradeoffs Between Travel Reliability, Congestion Mitigation Strategies and Emissions

  Capacity, demand, and vehicle based emissions reduction strategies are compared for several pollutants employing aggregate US congestion and vehicle fleet condition data. We find that congestion mitigation ...

  Citation × Citation Citation Abstract Copy Title: Value of Travel Time Reliability Part II: A Study of Tradeoffs Between Travel Reliability, Congestion Mitigation Strategies and Emissions Author: Figliozzi, Miguel A., Bigazzi, Alexander Y. Year: 2012 Capacity, demand, and vehicle based emissions reduction strategies are compared for several pollutants employing aggregate US congestion and vehicle fleet condition data. We find that congestion mitigation does not inevitably lead to reduced emissions; the net effect of mitigation depends on the balance of induced travel demand and increased vehicle efficiency that in turn depend on the pollutant, congestion level, and fleet composition. In the long run, capacity-based congestion improvements within certain speed intervals can reasonably be expected to increase emissions of CO2e, CO, and NOx through increased vehicle travel volume. Better opportunities for emissions reductions exist for HC and PM2.5 emissions, and on more heavily congested arterials. Advanced-efficiency vehicles with emissions rates that are less sensitive to congestion than conventional vehicles generate less emissions co-benefits from congestion mitigation. Title: Value of Travel Time Reliability Part II: A Study of Tradeoffs Between Travel Reliability, Congestion Mitigation Strategies and Emissions Author: Figliozzi, Miguel A., Bigazzi, Alexander Y. Year: 2012 Capacity, demand, and vehicle based emissions reduction strategies are compared for several pollutants employing aggregate US congestion and vehicle fleet condition data. We find that congestion mitigation does not inevitably lead to reduced emissions; the net effect of mitigation depends on the balance of induced travel demand and increased vehicle efficiency that in turn depend on the pollutant, congestion level, and fleet composition. In the long run, capacity-based congestion improvements within certain speed intervals can reasonably be expected to increase emissions of CO2e, CO, and NOx through increased vehicle travel volume. Better opportunities for emissions reductions exist for HC and PM2.5 emissions, and on more heavily congested arterials. Advanced-efficiency vehicles with emissions rates that are less sensitive to congestion than conventional vehicles generate less emissions co-benefits from congestion mitigation. Close

• 3. [Article] Application of LRFD Geotechnical Principles for Pile Supported Bridges in Oregon: Phase 1

  Bridge foundations must be designed based on acceptable risks of failure. To secure rapid implementation of Load Resistance Factor Design (LRFD) principles for foundation design, the American Association ...

  Citation × Citation Citation Abstract Copy Title: Application of LRFD Geotechnical Principles for Pile Supported Bridges in Oregon: Phase 1 Author: Smith, Trevor D., Dusicka, Peter Year: 2009 Bridge foundations must be designed based on acceptable risks of failure. To secure rapid implementation of Load Resistance Factor Design (LRFD) principles for foundation design, the American Association of State Highway and Transportation Officials (AASHTO) and the Federal Highway Administration (FHWA) are requiring their use through AASHTO code. The Bridge Section of the Oregon Department of Transportation (ODOT) has responsibility for satisfactory design of all the bridge structures across the state’s highway system. The widespread geotechnical adoption of the LRFD code throughout state DOTs has been difficult in the case of deep foundations due to regional differences and in some cases a lack of any close match to DOT foundation practices. This lack of matching stems from the source research conducted on which the code is based, documented as NCHRP 507. For ODOT, the evaluation of nominal axial static capacity for each driven pile in the field is conducted by dynamic methods and AASHTO offers resistance factors for these techniques. ODOT typically uses the wave equation software (WEAP) applied at the end of initial driving, EOID, and occasionally at the beginning of pile restrike (BOR) to capture increases in capacity from set-up. This study reports that, based on past and new surveys, ODOT practice is reasonably typical for DOT practice in sands, silts, and clays. The AASHTO resistance factor, φ, for WEAP is at EOID and is too low for the efficient design of piles to match the likely probabilities of pile failure. The survey of Northwest state DOTs revealed that 80% of the DOTs believe that a φ of 0.4 is conservative and 37.5 % do not use the AASHTO-sanctioned φ of 0.4. Matching LRFD to allowable stress design (ASD) by direct calibration for a single pile, without any reported capacity bias, sets φ as 0.55 to match the ASD factor of safety of 2.5. An ODOT case history of a recently completed pilesupported bridge designed and constructed to FHWA and AASHTO ASD standards in use at that time, shows the number of piles at the bent studied would be doubled under new AASHTO requirements. This suggests the standard will add considerable pile foundation costs to all new bridges. This cost increase is a strong incentive to complete statistical recalibration of GRLWEAP dynamic capacity resistance value in a Phase 2 of this study. Title: Application of LRFD Geotechnical Principles for Pile Supported Bridges in Oregon: Phase 1 Author: Smith, Trevor D., Dusicka, Peter Year: 2009 Bridge foundations must be designed based on acceptable risks of failure. To secure rapid implementation of Load Resistance Factor Design (LRFD) principles for foundation design, the American Association of State Highway and Transportation Officials (AASHTO) and the Federal Highway Administration (FHWA) are requiring their use through AASHTO code. The Bridge Section of the Oregon Department of Transportation (ODOT) has responsibility for satisfactory design of all the bridge structures across the state’s highway system. The widespread geotechnical adoption of the LRFD code throughout state DOTs has been difficult in the case of deep foundations due to regional differences and in some cases a lack of any close match to DOT foundation practices. This lack of matching stems from the source research conducted on which the code is based, documented as NCHRP 507. For ODOT, the evaluation of nominal axial static capacity for each driven pile in the field is conducted by dynamic methods and AASHTO offers resistance factors for these techniques. ODOT typically uses the wave equation software (WEAP) applied at the end of initial driving, EOID, and occasionally at the beginning of pile restrike (BOR) to capture increases in capacity from set-up. This study reports that, based on past and new surveys, ODOT practice is reasonably typical for DOT practice in sands, silts, and clays. The AASHTO resistance factor, φ, for WEAP is at EOID and is too low for the efficient design of piles to match the likely probabilities of pile failure. The survey of Northwest state DOTs revealed that 80% of the DOTs believe that a φ of 0.4 is conservative and 37.5 % do not use the AASHTO-sanctioned φ of 0.4. Matching LRFD to allowable stress design (ASD) by direct calibration for a single pile, without any reported capacity bias, sets φ as 0.55 to match the ASD factor of safety of 2.5. An ODOT case history of a recently completed pilesupported bridge designed and constructed to FHWA and AASHTO ASD standards in use at that time, shows the number of piles at the bent studied would be doubled under new AASHTO requirements. This suggests the standard will add considerable pile foundation costs to all new bridges. This cost increase is a strong incentive to complete statistical recalibration of GRLWEAP dynamic capacity resistance value in a Phase 2 of this study. Close

• 4. [Article] Bridge Damage Models for Seismic Risk Assessment of Oregon Highway Network

  The highway transportation network of the United States relies on the health and integrity of major infrastructure elements such as bridges. Frequently traveled parts of Oregon are within the seismically ...

  Citation × Citation Citation Abstract Copy Title: Bridge Damage Models for Seismic Risk Assessment of Oregon Highway Network Author: Dusicka, Peter, Roberts, Jeffery Year: 2011 The highway transportation network of the United States relies on the health and integrity of major infrastructure elements such as bridges. Frequently traveled parts of Oregon are within the seismically active Pacific Northwest and many of the bridges were designed and built to lateral demands that were assumed to be less than the current expectation, a deficiency caused by our growing awareness of seismic hazard and our enhanced understanding of the non-linear response of bridges. This vulnerability to damage from earthquakes can result in not only immediate damage, but also in potentially lingering economic impact caused by the disruption to traffic and freight mobility. Using analytical methods, fragility curves were constructed assuming lognormal capacity and demand distributions. Probability of failure was determined for the four damage state conditions of slight, moderate, extensive, and complete levels of damage. These statistical values were compared to the median and dispersion values proposed by other researchers, in addition to those calculated using guidelines from the HAZUS Technical Manual. Older multiple-span Oregon bridges were found to be significantly more fragile than the HAZUS models. As a result of this modeling and analysis effort, the relative fragility of the modeled typical 3-span and 5-span bridges was determined and quantified. Possible causes of the relatively high fragilities were also considered. Title: Bridge Damage Models for Seismic Risk Assessment of Oregon Highway Network Author: Dusicka, Peter, Roberts, Jeffery Year: 2011 The highway transportation network of the United States relies on the health and integrity of major infrastructure elements such as bridges. Frequently traveled parts of Oregon are within the seismically active Pacific Northwest and many of the bridges were designed and built to lateral demands that were assumed to be less than the current expectation, a deficiency caused by our growing awareness of seismic hazard and our enhanced understanding of the non-linear response of bridges. This vulnerability to damage from earthquakes can result in not only immediate damage, but also in potentially lingering economic impact caused by the disruption to traffic and freight mobility. Using analytical methods, fragility curves were constructed assuming lognormal capacity and demand distributions. Probability of failure was determined for the four damage state conditions of slight, moderate, extensive, and complete levels of damage. These statistical values were compared to the median and dispersion values proposed by other researchers, in addition to those calculated using guidelines from the HAZUS Technical Manual. Older multiple-span Oregon bridges were found to be significantly more fragile than the HAZUS models. As a result of this modeling and analysis effort, the relative fragility of the modeled typical 3-span and 5-span bridges was determined and quantified. Possible causes of the relatively high fragilities were also considered. Close

• 5. [Article] Contextual Influences on Trip Generation

  There is national interest in building data that expands upon the existing Institute of Transportation Engineers (ITE) trip generation rates to include sites located in a multi-modal context. Current ITE ...

  Citation × Citation Citation Abstract Copy Title: Contextual Influences on Trip Generation Author: Clifton, Kelly J., Currans, Kristina Marie, Muhs, Christopher D. Year: 2012 There is national interest in building data that expands upon the existing Institute of Transportation Engineers (ITE) trip generation rates to include sites located in a multi-modal context. Current ITE rates represent travel behavior for development in single lots and uses, primarily measured in low-density suburban areas. Despite evidence that a more compact urban form, access to transit and a greater mix of uses generates fewer and shorter vehicle trips, local governments are often compelled to use current ITE trip generation rates to evaluate transportation impacts and calculate transportation system development charges (TSDCs). This is due to: a) the expense of collecting local data, b) lack of alternative sources of information, c) the strong industry bias toward using ITE published rates and d) the absence of a empirically tested methodology for adjusting those rates for development occurring in different land use and transportation contexts. Compounding these challenges, cities in Oregon are required to demonstrate that planning and zoning changes will not degrade the performance of state-owned transportation facilities compared to the levels of service documented in the Regional Transportation Plan under the Oregon Transportation Planning Rule, section -0060, and Oregon Highway Plan, Policy 1.F.6. These requirements can conflict with regional policies in Metro's 2040 Growth Concept that call for development of mixed-use centers and corridors to support jobs and freight reliability, a compact urban form and leverage transportation investments such as high capacity transit. Thus, there are gaps in the understanding about how best to evaluate, mitigate and plan for growth under these conditions. This research proposes to develop multi-modal trip generation rates that better reflect the relationship between land use, transportation and travel demand for specific land use types located in various urban settings. The project aims to collect local data (using multi-modal counts and establishment surveys) on a few specific land uses (deemed most problematic to estimate demand and occurring across the spectrum of urban conditions) to develop trip generation rates that are sensitive to demographic, land use and transportation contexts. These new trip rates will be compared to the ITE rates for the same land use category and a methodology for adjusting the ITE rates will be developed. This adjustment methodology will be validated, using additional data collected in this research. The research will be documented and made available to local partners and disseminated widely to reach out to other communities across the country. The research conducted for this project would account for how the built environment (e.g., both land use and transportation) influences travel behavior (number of trips, trip length, mode choice), and determine trip rates that reflect the entire activity spectrum of different development/place typologies. This is extremely important in determining the impact of different development types on the transportation system to: 1) avoid over-planning the system for the surrounding land uses; (2) suggest strategies and investment priorities to encourage more compact, mixed-use areas with more transportation choices and 3) avoid creating regulatory and/or financial barriers to compact form envisioned by local, regional and statewide plans (i.e. uniform TSDCs can result in lower impact development paying the same rates, and thus subsidizing development with higher impact costs to the transportation system). The documentation of the findings and methodology will be applicable to current and future growth and be transferable to other communities, locally and nationally, beyond the Portland region. Title: Contextual Influences on Trip Generation Author: Clifton, Kelly J., Currans, Kristina Marie, Muhs, Christopher D. Year: 2012 There is national interest in building data that expands upon the existing Institute of Transportation Engineers (ITE) trip generation rates to include sites located in a multi-modal context. Current ITE rates represent travel behavior for development in single lots and uses, primarily measured in low-density suburban areas. Despite evidence that a more compact urban form, access to transit and a greater mix of uses generates fewer and shorter vehicle trips, local governments are often compelled to use current ITE trip generation rates to evaluate transportation impacts and calculate transportation system development charges (TSDCs). This is due to: a) the expense of collecting local data, b) lack of alternative sources of information, c) the strong industry bias toward using ITE published rates and d) the absence of a empirically tested methodology for adjusting those rates for development occurring in different land use and transportation contexts. Compounding these challenges, cities in Oregon are required to demonstrate that planning and zoning changes will not degrade the performance of state-owned transportation facilities compared to the levels of service documented in the Regional Transportation Plan under the Oregon Transportation Planning Rule, section -0060, and Oregon Highway Plan, Policy 1.F.6. These requirements can conflict with regional policies in Metro's 2040 Growth Concept that call for development of mixed-use centers and corridors to support jobs and freight reliability, a compact urban form and leverage transportation investments such as high capacity transit. Thus, there are gaps in the understanding about how best to evaluate, mitigate and plan for growth under these conditions. This research proposes to develop multi-modal trip generation rates that better reflect the relationship between land use, transportation and travel demand for specific land use types located in various urban settings. The project aims to collect local data (using multi-modal counts and establishment surveys) on a few specific land uses (deemed most problematic to estimate demand and occurring across the spectrum of urban conditions) to develop trip generation rates that are sensitive to demographic, land use and transportation contexts. These new trip rates will be compared to the ITE rates for the same land use category and a methodology for adjusting the ITE rates will be developed. This adjustment methodology will be validated, using additional data collected in this research. The research will be documented and made available to local partners and disseminated widely to reach out to other communities across the country. The research conducted for this project would account for how the built environment (e.g., both land use and transportation) influences travel behavior (number of trips, trip length, mode choice), and determine trip rates that reflect the entire activity spectrum of different development/place typologies. This is extremely important in determining the impact of different development types on the transportation system to: 1) avoid over-planning the system for the surrounding land uses; (2) suggest strategies and investment priorities to encourage more compact, mixed-use areas with more transportation choices and 3) avoid creating regulatory and/or financial barriers to compact form envisioned by local, regional and statewide plans (i.e. uniform TSDCs can result in lower impact development paying the same rates, and thus subsidizing development with higher impact costs to the transportation system). The documentation of the findings and methodology will be applicable to current and future growth and be transferable to other communities, locally and nationally, beyond the Portland region. Close