Search

Search Results

• 1. [Article] Behavior of Concrete Beams with Corroded Reinforcement Retrofitted with Carbon Fiber Reinforced Polymer

  Severe premature deterioration has been reported in a large number of reinforced concrete (RC) structures in corrosive environments. This research project focused on the behavior of beams that contained ...

  Citation × Citation Citation Abstract Copy Title: Behavior of Concrete Beams with Corroded Reinforcement Retrofitted with Carbon Fiber Reinforced Polymer Author: Lingga, Needa M. Year: 2016 Severe premature deterioration has been reported in a large number of reinforced concrete (RC) structures in corrosive environments. This research project focused on the behavior of beams that contained corroded steel and were retrofitted with CFRP. The steel in RC beams were assumed to be fully corroded, representing the most severe loss in steel cross-section. Unidirectional CFRP sheets were used to strengthen the deteriorated beams. The experimental program included testing five simply supported rectangular cross section concrete beams. All beams were approximately 1/3rd scale models, 4in. x 6in. cross sections, and 6ft. long. In three beams, the oiled steel rebars for flexure and shear were safely pulled out of the formwork after the concrete had cured a few hours, leaving voids. This technique was used to represent the total loss in steel cross-section in an extremely corrosive environment. The first specimen was a control beam with voids representing deteriorated steel. The second specimen was a plain concrete beam without voids. The third beam was another control specimen with flexural and shear reinforcement intact, representing the “original” beam before steel corrosion. The two remaining deteriorated beams were strengthened by externally bonding one and two layers of CFRP in the longitudinal and transverse directions. Beams were tested under third-point loading. Load carrying capacity, deflection, and ductility of the beams were measured. Test results showed that one layer of CFRP increased the load capacity to slightly higher than the “original” control beam, and two layers of CFRP increased it by a factor of two. The retrofitted specimens had a higher stiffness under service load conditions. The predict contribution of CFRP to flexure and shear capacities based on ACI 440.2R guidelines were in good agreement with test results. Title: Behavior of Concrete Beams with Corroded Reinforcement Retrofitted with Carbon Fiber Reinforced Polymer Author: Lingga, Needa M. Year: 2016 Severe premature deterioration has been reported in a large number of reinforced concrete (RC) structures in corrosive environments. This research project focused on the behavior of beams that contained corroded steel and were retrofitted with CFRP. The steel in RC beams were assumed to be fully corroded, representing the most severe loss in steel cross-section. Unidirectional CFRP sheets were used to strengthen the deteriorated beams. The experimental program included testing five simply supported rectangular cross section concrete beams. All beams were approximately 1/3rd scale models, 4in. x 6in. cross sections, and 6ft. long. In three beams, the oiled steel rebars for flexure and shear were safely pulled out of the formwork after the concrete had cured a few hours, leaving voids. This technique was used to represent the total loss in steel cross-section in an extremely corrosive environment. The first specimen was a control beam with voids representing deteriorated steel. The second specimen was a plain concrete beam without voids. The third beam was another control specimen with flexural and shear reinforcement intact, representing the “original” beam before steel corrosion. The two remaining deteriorated beams were strengthened by externally bonding one and two layers of CFRP in the longitudinal and transverse directions. Beams were tested under third-point loading. Load carrying capacity, deflection, and ductility of the beams were measured. Test results showed that one layer of CFRP increased the load capacity to slightly higher than the “original” control beam, and two layers of CFRP increased it by a factor of two. The retrofitted specimens had a higher stiffness under service load conditions. The predict contribution of CFRP to flexure and shear capacities based on ACI 440.2R guidelines were in good agreement with test results. Close

• 2. [Article] Experimental Investigation of Fiber Reinforced Concrete Beams

  Shear strength of fiber reinforced concrete beams was studied in this research project. Three types of fibers were examined: hooked-end steel fiber, crimped-steel fiber, and crimped-monofilament polypropylene ...

  Citation × Citation Citation Abstract Copy Title: Experimental Investigation of Fiber Reinforced Concrete Beams Author: Al-lami, Karrar Ali Year: 2015 Shear strength of fiber reinforced concrete beams was studied in this research project. Three types of fibers were examined: hooked-end steel fiber, crimped-steel fiber, and crimped-monofilament polypropylene fibers. The experimental program included five beam specimens. Two of the beams were control specimens in which one was reinforced with minimum shear reinforcement according to ACI 318, while the other one did not have any shear reinforcement. Each one of the other three specimens was reinforced with one of the above mentioned fibers by 1% volumetric ratio. In addition to the beam specimens, three prisms were also made for each type fiber to determine their toughness. The aim of this research was to investigate the following questions for medium-high concrete strength 1) to evaluate the effectiveness of each type of fibers on the shear strength, 2) to investigate the shear strength, toughness, crack patterns and near ultimate load crack width of each beam, and 3) to determine if using 1% volumetric ratio of fibers as shear reinforcement in beams would provide adequate strength and stiffness properties comparable to reinforcing steel used as minimum shear reinforcement. The results showed that all three types of fibers increased the shear capacity of the beam specimens more than the beam reinforced with minimum shear reinforcement. Moreover, some of the fibers used could shift the type of failure from a pure shear failure to a combined flexural-shear or pure flexural failure. Title: Experimental Investigation of Fiber Reinforced Concrete Beams Author: Al-lami, Karrar Ali Year: 2015 Shear strength of fiber reinforced concrete beams was studied in this research project. Three types of fibers were examined: hooked-end steel fiber, crimped-steel fiber, and crimped-monofilament polypropylene fibers. The experimental program included five beam specimens. Two of the beams were control specimens in which one was reinforced with minimum shear reinforcement according to ACI 318, while the other one did not have any shear reinforcement. Each one of the other three specimens was reinforced with one of the above mentioned fibers by 1% volumetric ratio. In addition to the beam specimens, three prisms were also made for each type fiber to determine their toughness. The aim of this research was to investigate the following questions for medium-high concrete strength 1) to evaluate the effectiveness of each type of fibers on the shear strength, 2) to investigate the shear strength, toughness, crack patterns and near ultimate load crack width of each beam, and 3) to determine if using 1% volumetric ratio of fibers as shear reinforcement in beams would provide adequate strength and stiffness properties comparable to reinforcing steel used as minimum shear reinforcement. The results showed that all three types of fibers increased the shear capacity of the beam specimens more than the beam reinforced with minimum shear reinforcement. Moreover, some of the fibers used could shift the type of failure from a pure shear failure to a combined flexural-shear or pure flexural failure. Close