Search

Search Results

• 1. [Article] Upper Spokane River Model: Boundary Conditions and Model Setup, 2001

  The Washington Department of Ecology is interested in a water quality model for the Upper Spokane River system for use in developing Total Maximum Daily Loads (TMDLs). The goals of this modeling effort ...

  Citation × Citation Citation Abstract Copy Title: Upper Spokane River Model: Boundary Conditions and Model Setup, 2001 Author: Slominski, Spencer, Annear, Robert Leslie, Berger, Chris, Wells, Scott A. Year: 2002 The Washington Department of Ecology is interested in a water quality model for the Upper Spokane River system for use in developing Total Maximum Daily Loads (TMDLs). The goals of this modeling effort are to: • Gather data to construct a computer simulation model of the Spokane River system including Long Lake Reservoir and the pools behind Nine Mile dam, Upper Falls dam and Upriver dam for 2001 based on the calibration conducted for 1991 and 2000 data sets, (Annear et al, 2001). • Ensure that the model accurately represents the system hydrodynamics and water quality (flow, temperature, dissolved oxygen and nutrient dynamics) for the three simulation years A hydrodynamic and water quality model, CE-QUAL-W2 Version 3 (Wells, 1997), is being applied to model the Spokane River system. CE-QUAL-W2 is a two dimensional (longitudinal-vertical), laterally averaged, hydrodynamic and water quality model that has been under development by the Corps of Engineers Waterways Experiment Station (Cole and Wells, 2000). In order to model the system, the following data were required: • Spokane River flow, water level and water quality data at the upstream system boundary (the State of Idaho boundary) • Tributary inflows and water quality • Meteorological conditions • Bathymetry of the Spokane River, the dam pools along the river, and Long Lake Reservoir • Point source (wastewater treatment plants, WWTPs) inflows and water quality characteristics Data have been primarily collected from 1991 to 1992, during 2000, and more recently during 2001. This report summarizes the 2001 data used in the modeling effort to expand the model calibration period. Title: Upper Spokane River Model: Boundary Conditions and Model Setup, 2001 Author: Slominski, Spencer, Annear, Robert Leslie, Berger, Chris, Wells, Scott A. Year: 2002 The Washington Department of Ecology is interested in a water quality model for the Upper Spokane River system for use in developing Total Maximum Daily Loads (TMDLs). The goals of this modeling effort are to: • Gather data to construct a computer simulation model of the Spokane River system including Long Lake Reservoir and the pools behind Nine Mile dam, Upper Falls dam and Upriver dam for 2001 based on the calibration conducted for 1991 and 2000 data sets, (Annear et al, 2001). • Ensure that the model accurately represents the system hydrodynamics and water quality (flow, temperature, dissolved oxygen and nutrient dynamics) for the three simulation years A hydrodynamic and water quality model, CE-QUAL-W2 Version 3 (Wells, 1997), is being applied to model the Spokane River system. CE-QUAL-W2 is a two dimensional (longitudinal-vertical), laterally averaged, hydrodynamic and water quality model that has been under development by the Corps of Engineers Waterways Experiment Station (Cole and Wells, 2000). In order to model the system, the following data were required: • Spokane River flow, water level and water quality data at the upstream system boundary (the State of Idaho boundary) • Tributary inflows and water quality • Meteorological conditions • Bathymetry of the Spokane River, the dam pools along the river, and Long Lake Reservoir • Point source (wastewater treatment plants, WWTPs) inflows and water quality characteristics Data have been primarily collected from 1991 to 1992, during 2000, and more recently during 2001. This report summarizes the 2001 data used in the modeling effort to expand the model calibration period. Close

• 2. [Article] Upper Spokane River Model: Boundary Conditions and Model Setup, 1991 and 2000

  The Washington Department of Ecology is interested in a water quality model for the Upper Spokane River system for use in developing Total Maximum Daily Loads (TMDLs). The goals of this modeling effort ...

  Citation × Citation Citation Abstract Copy Title: Upper Spokane River Model: Boundary Conditions and Model Setup, 1991 and 2000 Author: Annear, Robert Leslie, Berger, Chris, Wells, Scott A. Year: 2001 The Washington Department of Ecology is interested in a water quality model for the Upper Spokane River system for use in developing Total Maximum Daily Loads (TMDLs). The goals of this modeling effort are to: • Gather data to construct a computer simulation model of the Spokane River system including Long Lake Reservoir and the pools behind Nine Mile dam, Upper Falls dam and Upriver dam • Ensure that the model accurately represents the system hydrodynamics and water quality (flow, temperature, dissolved oxygen and nutrient dynamics) A hydrodynamic and water quality model, CE-QUAL-W2 Version 3 (Wells, 1997), is being applied to model the Spokane River system. CE-QUAL-W2 is a two dimensional (longitudinal-vertical), laterally averaged, hydrodynamic and water quality model that has been under development by the Corps of Engineers Waterways Experiments Station (Cole and Wells, 2000). In order to model the system, the following data were required: • Spokane River flow, water level and water quality data at the upstream system boundary (the State of Idaho boundary) • Tributary inflows and water quality • Meteorological conditions • Bathymetry of the Spokane River, the dam pools along the river, and Long Lake Reservoir • Point source (wastewater treatment plants, WWTPs) inflows and water quality characteristics Data have been primarily collected from 1991 to 1992 and again during 2000. This report summarizes the data used in the modeling effort. Title: Upper Spokane River Model: Boundary Conditions and Model Setup, 1991 and 2000 Author: Annear, Robert Leslie, Berger, Chris, Wells, Scott A. Year: 2001 The Washington Department of Ecology is interested in a water quality model for the Upper Spokane River system for use in developing Total Maximum Daily Loads (TMDLs). The goals of this modeling effort are to: • Gather data to construct a computer simulation model of the Spokane River system including Long Lake Reservoir and the pools behind Nine Mile dam, Upper Falls dam and Upriver dam • Ensure that the model accurately represents the system hydrodynamics and water quality (flow, temperature, dissolved oxygen and nutrient dynamics) A hydrodynamic and water quality model, CE-QUAL-W2 Version 3 (Wells, 1997), is being applied to model the Spokane River system. CE-QUAL-W2 is a two dimensional (longitudinal-vertical), laterally averaged, hydrodynamic and water quality model that has been under development by the Corps of Engineers Waterways Experiments Station (Cole and Wells, 2000). In order to model the system, the following data were required: • Spokane River flow, water level and water quality data at the upstream system boundary (the State of Idaho boundary) • Tributary inflows and water quality • Meteorological conditions • Bathymetry of the Spokane River, the dam pools along the river, and Long Lake Reservoir • Point source (wastewater treatment plants, WWTPs) inflows and water quality characteristics Data have been primarily collected from 1991 to 1992 and again during 2000. This report summarizes the data used in the modeling effort. Close

• 3. [Article] Upper Spokane River Model: Model Calibration, 1991 and 2000

  The Washington Department of Ecology is interested in a water quality model for the Upper Spokane River system for use in developing Total Maximum Daily Loads (TMDLs). The goals of this modeling effort ...

  Citation × Citation Citation Abstract Copy Title: Upper Spokane River Model: Model Calibration, 1991 and 2000 Author: Berger, Chris, Annear, Robert Leslie, Wells, Scott A. Year: 2002 The Washington Department of Ecology is interested in a water quality model for the Upper Spokane River system for use in developing Total Maximum Daily Loads (TMDLs). The goals of this modeling effort are to: • Gather data to construct a computer simulation model of the Spokane River system including Long Lake Reservoir and the pools behind Nine Mile dam, Upper Falls dam and Upriver dam. • Ensure that the model accurately represents the system hydrodynamics and water quality (flow, temperature, dissolved oxygen and nutrient dynamics) This report evaluates the model calibration and discusses issues relative to that calibration effort. The calibration effort focused on model predictions of hydrodynamics (flow and water level), temperature, and eutrophication model parameters (such as nutrients, algae, dissolved oxygen, organic matter, coliform). The model calibration periods were from February 1, 1991 to October 31, 1991 and from January 1, 2000 to October 31, 2000. Title: Upper Spokane River Model: Model Calibration, 1991 and 2000 Author: Berger, Chris, Annear, Robert Leslie, Wells, Scott A. Year: 2002 The Washington Department of Ecology is interested in a water quality model for the Upper Spokane River system for use in developing Total Maximum Daily Loads (TMDLs). The goals of this modeling effort are to: • Gather data to construct a computer simulation model of the Spokane River system including Long Lake Reservoir and the pools behind Nine Mile dam, Upper Falls dam and Upriver dam. • Ensure that the model accurately represents the system hydrodynamics and water quality (flow, temperature, dissolved oxygen and nutrient dynamics) This report evaluates the model calibration and discusses issues relative to that calibration effort. The calibration effort focused on model predictions of hydrodynamics (flow and water level), temperature, and eutrophication model parameters (such as nutrients, algae, dissolved oxygen, organic matter, coliform). The model calibration periods were from February 1, 1991 to October 31, 1991 and from January 1, 2000 to October 31, 2000. Close

• 4. [Article] Pend Oreille River, Box Canyon Model: Model Development and Calibration

  The purpose of this study was to improve the existing Version 3.0 application of CE-QUAL-W2 of the Pend Oreille River between Box Canyon Dam and Albeni Falls Dam by performing the tasks outlined above. ...

  Citation × Citation Citation Abstract Copy Title: Pend Oreille River, Box Canyon Model: Model Development and Calibration Author: Annear, Robert Leslie, Berger, Chris, Wells, Scott A. Year: 2006 The purpose of this study was to improve the existing Version 3.0 application of CE-QUAL-W2 of the Pend Oreille River between Box Canyon Dam and Albeni Falls Dam by performing the tasks outlined above. In addition, the use of field data from 2004 as an additional calibration year would improve the confidence in the model’s predictive ability for temperature. The model simulations were run from January 1st to December 31st in each of the 3 years of model simulation: 1997, 1998 and 2004. The model chosen for development is CE-QUAL-W2 Version 3.5 (Cole and Wells, 2006). This is a twodimensional unsteady hydrodynamic and water quality model that includes typical eutrophication parameters (algae, nutrients, temperature, organic matter, dissolved oxygen, pH). The PSU-WQRG is a center for development of this modeling tool (see http://www.cee.pdx.edu/w2). Title: Pend Oreille River, Box Canyon Model: Model Development and Calibration Author: Annear, Robert Leslie, Berger, Chris, Wells, Scott A. Year: 2006 The purpose of this study was to improve the existing Version 3.0 application of CE-QUAL-W2 of the Pend Oreille River between Box Canyon Dam and Albeni Falls Dam by performing the tasks outlined above. In addition, the use of field data from 2004 as an additional calibration year would improve the confidence in the model’s predictive ability for temperature. The model simulations were run from January 1st to December 31st in each of the 3 years of model simulation: 1997, 1998 and 2004. The model chosen for development is CE-QUAL-W2 Version 3.5 (Cole and Wells, 2006). This is a twodimensional unsteady hydrodynamic and water quality model that includes typical eutrophication parameters (algae, nutrients, temperature, organic matter, dissolved oxygen, pH). The PSU-WQRG is a center for development of this modeling tool (see http://www.cee.pdx.edu/w2). Close

• 5. [Article] Pend Oreille River, Box Canyon Model: Model Scenario Simulations

  The Washington Department of Ecology is interested in developing a temperature Total Maximum Daily Load (TMDL) allocation for the Pend Oreille River between the Albeni Falls Dam (U.S. Army Corps of Engineer’s ...

  Citation × Citation Citation Abstract Copy Title: Pend Oreille River, Box Canyon Model: Model Scenario Simulations Author: Berger, Chris, Annear, Robert Leslie, Wells, Scott A. Year: 2007 The Washington Department of Ecology is interested in developing a temperature Total Maximum Daily Load (TMDL) allocation for the Pend Oreille River between the Albeni Falls Dam (U.S. Army Corps of Engineer’s reservoir) and Box Canyon Dam as shown in Figure 1. The Pend Oreille drainage basin is shown in Figure 2. An existing model of the Box Canyon reach was updated from CE-QUALW2 Version 3.0 to Version 3.5. This current research involves improving the calibration of the original model (1997 and 1998) and expanding the model using 2004 as an additional data set for calibration. The use of field data from 2004 as an additional calibration year was chosen to improve the confidence in the model’s predictive ability for temperature. Hence, the model simulations were run from January 1st to December 31st in each of the 3 years of model simulation: 1997, 1998 and 2004. The model chosen for development is CE-QUAL-W2 Version 3.5 (Cole and Wells, 2006). This is a twodimensional unsteady hydrodynamic and water quality model that includes typical eutrophication parameters (algae, nutrients, temperature, organic matter, dissolved oxygen, pH). The PSU-WQRG (Water Quality Research Group) is a center for development of this modeling tool (see http://www.cee.pdx.edu/w2). The model simulation for scenarios was run from January 1st, 2004 to September 25th, 2005. Title: Pend Oreille River, Box Canyon Model: Model Scenario Simulations Author: Berger, Chris, Annear, Robert Leslie, Wells, Scott A. Year: 2007 The Washington Department of Ecology is interested in developing a temperature Total Maximum Daily Load (TMDL) allocation for the Pend Oreille River between the Albeni Falls Dam (U.S. Army Corps of Engineer’s reservoir) and Box Canyon Dam as shown in Figure 1. The Pend Oreille drainage basin is shown in Figure 2. An existing model of the Box Canyon reach was updated from CE-QUALW2 Version 3.0 to Version 3.5. This current research involves improving the calibration of the original model (1997 and 1998) and expanding the model using 2004 as an additional data set for calibration. The use of field data from 2004 as an additional calibration year was chosen to improve the confidence in the model’s predictive ability for temperature. Hence, the model simulations were run from January 1st to December 31st in each of the 3 years of model simulation: 1997, 1998 and 2004. The model chosen for development is CE-QUAL-W2 Version 3.5 (Cole and Wells, 2006). This is a twodimensional unsteady hydrodynamic and water quality model that includes typical eutrophication parameters (algae, nutrients, temperature, organic matter, dissolved oxygen, pH). The PSU-WQRG (Water Quality Research Group) is a center for development of this modeling tool (see http://www.cee.pdx.edu/w2). The model simulation for scenarios was run from January 1st, 2004 to September 25th, 2005. Close

• 6. [Article] Upper Spokane River Model in Idaho: Boundary Conditions and Model Setup and Calibration for 2001 and 2004

  As a result of a Total Maximum Daily Load (TMDL) study of the Spokane River in Washington, a hydrodynamic and water quality model for the Spokane River was developed by Portland State University (PSU) ...

  Citation × Citation Citation Abstract Copy Title: Upper Spokane River Model in Idaho: Boundary Conditions and Model Setup and Calibration for 2001 and 2004 Author: Annear, Robert Leslie, Wells, Scott A., Berger, Chris Year: 2005 As a result of a Total Maximum Daily Load (TMDL) study of the Spokane River in Washington, a hydrodynamic and water quality model for the Spokane River was developed by Portland State University (PSU) for the Corps of Engineers and the Washington Department of Ecology from the Washington-Idaho state line to the outlet of Long Lake. An earlier study of the Spokane River was undertaken by Limno-Tech (2001a, 2001b) for the domain shown in Figure 3. Limno-Tech used an earlier version of CE-QUAL-W2, Version 2, for the Reservoir portion of the Spokane River from Post Falls Dam to Coeur d’Alene Lake and a steady-state EPA model, QUAL2E, for the riverine section from Post Falls Dam to the Idaho-Washington State Line. The steady-state QUAL2E model was not adequate to deal with flow and water quality dynamics. Hence, the riverine portion of the model and the reservoir portion were both upgraded to CE-QUAL-W2 Version 3.1. PSU developed the CE-QUAL-W2 model, but did not have adequate data for model calibration. The set-up of this model was described in the following report: * Wells et al. (2003) - Upper Spokane River Model in Idaho: Boundary Conditions and Model Setup for 2001 Because of the necessity of looking at the entire river basin, a model using CE-QUAL-W2 Version 3.1 of the Idaho portion of the Spokane River model was developed to assess water quality management strategies for the Idaho side of the Spokane River. The objective of this study was to use new field data from 2001 and 2004 to improve the model calibration for the Idaho portion of the Spokane River and reevaluate the work done by Wells et al. (2003). Title: Upper Spokane River Model in Idaho: Boundary Conditions and Model Setup and Calibration for 2001 and 2004 Author: Annear, Robert Leslie, Wells, Scott A., Berger, Chris Year: 2005 As a result of a Total Maximum Daily Load (TMDL) study of the Spokane River in Washington, a hydrodynamic and water quality model for the Spokane River was developed by Portland State University (PSU) for the Corps of Engineers and the Washington Department of Ecology from the Washington-Idaho state line to the outlet of Long Lake. An earlier study of the Spokane River was undertaken by Limno-Tech (2001a, 2001b) for the domain shown in Figure 3. Limno-Tech used an earlier version of CE-QUAL-W2, Version 2, for the Reservoir portion of the Spokane River from Post Falls Dam to Coeur d’Alene Lake and a steady-state EPA model, QUAL2E, for the riverine section from Post Falls Dam to the Idaho-Washington State Line. The steady-state QUAL2E model was not adequate to deal with flow and water quality dynamics. Hence, the riverine portion of the model and the reservoir portion were both upgraded to CE-QUAL-W2 Version 3.1. PSU developed the CE-QUAL-W2 model, but did not have adequate data for model calibration. The set-up of this model was described in the following report: * Wells et al. (2003) - Upper Spokane River Model in Idaho: Boundary Conditions and Model Setup for 2001 Because of the necessity of looking at the entire river basin, a model using CE-QUAL-W2 Version 3.1 of the Idaho portion of the Spokane River model was developed to assess water quality management strategies for the Idaho side of the Spokane River. The objective of this study was to use new field data from 2001 and 2004 to improve the model calibration for the Idaho portion of the Spokane River and reevaluate the work done by Wells et al. (2003). Close

• 7. [Article] Upper Spokane River Model in Idaho: Boundary Conditions and Model Setup for 2001

  The Spokane River in Idaho originates in Coeur d’Alene Lake (Figure 1 and Figure 2). The section of the Spokane River from Coeur d’Alene Lake to the Washington state line is the subject of a water quality ...

  Citation × Citation Citation Abstract Copy Title: Upper Spokane River Model in Idaho: Boundary Conditions and Model Setup for 2001 Author: Wells, Scott A., Annear, Robert Leslie, Berger, Chris Year: 2003 The Spokane River in Idaho originates in Coeur d’Alene Lake (Figure 1 and Figure 2). The section of the Spokane River from Coeur d’Alene Lake to the Washington state line is the subject of a water quality study for the US Environmental Protection Agency. The objective of this study is to create a water quality and hydrodynamic model of the Spokane River in Idaho using CE-QUAL-W2 Version 3.1 (Cole and Wells, 2002). Since the Spokane River is water quality limited, a hydrodynamic and water quality model for the Spokane River in Washington was developed by Portland State University for the Corps of Engineers and the Washington Department of Ecology from the Idaho border to the outlet of Long Lake. An earlier study of the Spokane River was undertaken by Limno-Tech (2001a, 2001b) for the domain shown in Figure 3. Limno-Tech used an earlier version of CE-QUAL-W2, Version 2, for the Reservoir portion of the Spokane River from Post Falls Dam to Coeur d’Alene Lake and a steady-state EPA model, QUAL2E, for the riverine section from Post Falls Dam to the Idaho-Washington border. The steady-state QUAL2E model was not adequate to deal with flow and water quality dynamics. Hence, the riverine portion of the model and the reservoir portion were both upgraded to CE-QUAL-W2 Version 3.1. Because of the necessity of looking at the entire water basin, a model using CE-QUAL-W2 Version 3.1 of the Idaho portion of the Spokane River model was developed to assess water quality management strategies for the Idaho side of the Spokane River. Title: Upper Spokane River Model in Idaho: Boundary Conditions and Model Setup for 2001 Author: Wells, Scott A., Annear, Robert Leslie, Berger, Chris Year: 2003 The Spokane River in Idaho originates in Coeur d’Alene Lake (Figure 1 and Figure 2). The section of the Spokane River from Coeur d’Alene Lake to the Washington state line is the subject of a water quality study for the US Environmental Protection Agency. The objective of this study is to create a water quality and hydrodynamic model of the Spokane River in Idaho using CE-QUAL-W2 Version 3.1 (Cole and Wells, 2002). Since the Spokane River is water quality limited, a hydrodynamic and water quality model for the Spokane River in Washington was developed by Portland State University for the Corps of Engineers and the Washington Department of Ecology from the Idaho border to the outlet of Long Lake. An earlier study of the Spokane River was undertaken by Limno-Tech (2001a, 2001b) for the domain shown in Figure 3. Limno-Tech used an earlier version of CE-QUAL-W2, Version 2, for the Reservoir portion of the Spokane River from Post Falls Dam to Coeur d’Alene Lake and a steady-state EPA model, QUAL2E, for the riverine section from Post Falls Dam to the Idaho-Washington border. The steady-state QUAL2E model was not adequate to deal with flow and water quality dynamics. Hence, the riverine portion of the model and the reservoir portion were both upgraded to CE-QUAL-W2 Version 3.1. Because of the necessity of looking at the entire water basin, a model using CE-QUAL-W2 Version 3.1 of the Idaho portion of the Spokane River model was developed to assess water quality management strategies for the Idaho side of the Spokane River. Close

• 8. [Article] Willamette River Basin Temperature TMDL Model: Model Calibration

  The State of Oregon Department of Environmental Quality (DEQ) is developing a TMDL for temperature in the Willamette River basin shown in Figure 1. The study area included the Willamette River and all ...

  Citation × Citation Citation Abstract Copy Title: Willamette River Basin Temperature TMDL Model: Model Calibration Author: Berger, Chris, McKillip, Michael Lee, Annear, Robert Leslie, Khan, Sher Jamal, Wells, Scott A. Year: 2004 The State of Oregon Department of Environmental Quality (DEQ) is developing a TMDL for temperature in the Willamette River basin shown in Figure 1. The study area included the Willamette River and all major tributaries (except the Tualatin River where a TMDL process was already concluded). A large section of the Columbia River was also modeled to provide adequate boundary representation of tidal flows in the lower Willamette River. The Willamette River below the Oregon City Falls in the Portland metropolitan area has a typical diurnal tidal range of 1 m. The development of a dynamic model of temperature and hydrodynamics of the entire river basin incorporating shading were primary requirements of this modeling study. The model would be used by DEQ to set temperature limits on point source dischargers and to evaluate the impact of management strategies on river temperatures to improve fish habitat. Some of these strategies included modifications of the dam at the Willamette River Falls south of Portland and channel reconfigurations. The river basin model was originally divided into several reaches. Individual models were developed for each reach. The models were set-up for each section of the Willamette basin as described in Annear et al. (2004a), the models were calibrated to field data and management strategies were evaluated as described in Annear et al (2004b). This report outlines the model calibration of each of these model sections or elements for both the calibration time periods. The calibration period for each model section differs due to the availability of boundary condition data. The model management simulation scenarios (Annear et al, 2004b) also required boundary condition data that extended past the calibration periods. Title: Willamette River Basin Temperature TMDL Model: Model Calibration Author: Berger, Chris, McKillip, Michael Lee, Annear, Robert Leslie, Khan, Sher Jamal, Wells, Scott A. Year: 2004 The State of Oregon Department of Environmental Quality (DEQ) is developing a TMDL for temperature in the Willamette River basin shown in Figure 1. The study area included the Willamette River and all major tributaries (except the Tualatin River where a TMDL process was already concluded). A large section of the Columbia River was also modeled to provide adequate boundary representation of tidal flows in the lower Willamette River. The Willamette River below the Oregon City Falls in the Portland metropolitan area has a typical diurnal tidal range of 1 m. The development of a dynamic model of temperature and hydrodynamics of the entire river basin incorporating shading were primary requirements of this modeling study. The model would be used by DEQ to set temperature limits on point source dischargers and to evaluate the impact of management strategies on river temperatures to improve fish habitat. Some of these strategies included modifications of the dam at the Willamette River Falls south of Portland and channel reconfigurations. The river basin model was originally divided into several reaches. Individual models were developed for each reach. The models were set-up for each section of the Willamette basin as described in Annear et al. (2004a), the models were calibrated to field data and management strategies were evaluated as described in Annear et al (2004b). This report outlines the model calibration of each of these model sections or elements for both the calibration time periods. The calibration period for each model section differs due to the availability of boundary condition data. The model management simulation scenarios (Annear et al, 2004b) also required boundary condition data that extended past the calibration periods. Close

• 9. [Article] Willamette River Basin Temperature TMDL Model: Model Scenarios

  The State of Oregon Department of Environmental Quality (DEQ) is developing a TMDL for temperature in the Willamette River basin shown in Figure 1. The study area included the Willamette River and all ...

  Citation × Citation Citation Abstract Copy Title: Willamette River Basin Temperature TMDL Model: Model Scenarios Author: Annear, Robert Leslie, McKillip, Michael Lee, Khan, Sher Jamal, Berger, Chris, Wells, Scott A. Year: 2004 The State of Oregon Department of Environmental Quality (DEQ) is developing a TMDL for temperature in the Willamette River basin shown in Figure 1. The study area included the Willamette River and all major tributaries (except the Tualatin River where a TMDL process was already concluded). A large section of the Columbia River was also modeled to provide adequate boundary representation of tidal flows in the lower Willamette River. The Willamette River below the Oregon City Falls in the Portland metropolitan area has a typical diurnal tidal range of 1 m. The development of a dynamic model of temperature and hydrodynamics of the entire river basin incorporating shading were primary requirements of this modeling study. The model would be used by DEQ to set temperature limits on point source dischargers and to evaluate the impact of management strategies on river temperatures to improve fish habitat. Some of these strategies included modifications of the dam at the Willamette River Falls south of Portland and channel reconfigurations. Once the models were set-up for each section of the Willamette basin, the model was calibrated to field data and management strategies were evaluated. These are the subjects of two other reports: Annear et al. (2004) and Berger et al. (2004). This report outlines the results of implementing model scenarios for each of the model sections or elements for specific time periods. The model scenario simulation periods used to investigate management scenarios required boundary condition data that extended past the model calibration periods. The model simulation period for year 2001 was from June 1 to October 31 and for year 2002 from April 1 to October 31. Title: Willamette River Basin Temperature TMDL Model: Model Scenarios Author: Annear, Robert Leslie, McKillip, Michael Lee, Khan, Sher Jamal, Berger, Chris, Wells, Scott A. Year: 2004 The State of Oregon Department of Environmental Quality (DEQ) is developing a TMDL for temperature in the Willamette River basin shown in Figure 1. The study area included the Willamette River and all major tributaries (except the Tualatin River where a TMDL process was already concluded). A large section of the Columbia River was also modeled to provide adequate boundary representation of tidal flows in the lower Willamette River. The Willamette River below the Oregon City Falls in the Portland metropolitan area has a typical diurnal tidal range of 1 m. The development of a dynamic model of temperature and hydrodynamics of the entire river basin incorporating shading were primary requirements of this modeling study. The model would be used by DEQ to set temperature limits on point source dischargers and to evaluate the impact of management strategies on river temperatures to improve fish habitat. Some of these strategies included modifications of the dam at the Willamette River Falls south of Portland and channel reconfigurations. Once the models were set-up for each section of the Willamette basin, the model was calibrated to field data and management strategies were evaluated. These are the subjects of two other reports: Annear et al. (2004) and Berger et al. (2004). This report outlines the results of implementing model scenarios for each of the model sections or elements for specific time periods. The model scenario simulation periods used to investigate management scenarios required boundary condition data that extended past the model calibration periods. The model simulation period for year 2001 was from June 1 to October 31 and for year 2002 from April 1 to October 31. Close

• 10. [Article] Willamette River Basin Temperature TMDL Model: Boundary Conditions and Model Setup

  The State of Oregon Department of Environmental Quality (DEQ) is developing a TMDL for temperature in the Willamette River basin shown in Figure 1. The study area included the Willamette River and all ...

  Citation × Citation Citation Abstract Copy Title: Willamette River Basin Temperature TMDL Model: Boundary Conditions and Model Setup Author: Annear, Robert Leslie, McKillip, Michael Lee, Khan, Sher Jamal, Berger, Chris, Wells, Scott A. Year: 2004 The State of Oregon Department of Environmental Quality (DEQ) is developing a TMDL for temperature in the Willamette River basin shown in Figure 1. The study area included the Willamette River and all major tributaries (except the Tualatin River where a TMDL process was already concluded). A large section of the Columbia River was also modeled to provide adequate boundary representation of tidal flows in the lower Willamette River. The Willamette River below the Oregon City Falls in the Portland metropolitan area has a typical diurnal tidal range of 1 m. The development of a dynamic model of temperature and hydrodynamics of the entire river basin incorporating shading were primary requirements of this modeling study. The model would be used by DEQ to set temperature limits on point source dischargers and to evaluate the impact of management strategies on river temperatures to improve fish habitat. Some of these strategies included modifications of the dam at the Willamette River Falls south of Portland and channel reconfigurations. Once the models were set-up for each section of the Willamette basin, the model was calibrated to field data and management strategies were evaluated. These are the subjects of two other reports: Annear et al. (2004b) and Berger et al. (2004). This report outlines the model development of each of these model sections or elements for both the calibration time periods and the management scenario time periods. The calibration period for each model section differs due to the availability of boundary condition data. The model simulation periods used to investigate management scenarios (Annear et al, 2004b) also required boundary condition data that extended past the calibration periods. Title: Willamette River Basin Temperature TMDL Model: Boundary Conditions and Model Setup Author: Annear, Robert Leslie, McKillip, Michael Lee, Khan, Sher Jamal, Berger, Chris, Wells, Scott A. Year: 2004 The State of Oregon Department of Environmental Quality (DEQ) is developing a TMDL for temperature in the Willamette River basin shown in Figure 1. The study area included the Willamette River and all major tributaries (except the Tualatin River where a TMDL process was already concluded). A large section of the Columbia River was also modeled to provide adequate boundary representation of tidal flows in the lower Willamette River. The Willamette River below the Oregon City Falls in the Portland metropolitan area has a typical diurnal tidal range of 1 m. The development of a dynamic model of temperature and hydrodynamics of the entire river basin incorporating shading were primary requirements of this modeling study. The model would be used by DEQ to set temperature limits on point source dischargers and to evaluate the impact of management strategies on river temperatures to improve fish habitat. Some of these strategies included modifications of the dam at the Willamette River Falls south of Portland and channel reconfigurations. Once the models were set-up for each section of the Willamette basin, the model was calibrated to field data and management strategies were evaluated. These are the subjects of two other reports: Annear et al. (2004b) and Berger et al. (2004). This report outlines the model development of each of these model sections or elements for both the calibration time periods and the management scenario time periods. The calibration period for each model section differs due to the availability of boundary condition data. The model simulation periods used to investigate management scenarios (Annear et al, 2004b) also required boundary condition data that extended past the calibration periods. Close