Search

Search Results

• 1. [Image] Transient well testing in two-phase geothermal reservoirs

  	A study of well test analysis techniques in two-phase geothermal reservoirs has been conducted using a three-dimensional, two-phase, wellbore and reservoir simulation model. Well tests from Cerro Prieto ...
  	Citation × Citation Citation Abstract Copy Title: Transient well testing in two-phase geothermal reservoirs Author: Aydelotte, S.R. Year: 1980 A study of well test analysis techniques in two-phase geothermal reservoirs has been conducted using a three-dimensional, two-phase, wellbore and reservoir simulation model. Well tests from Cerro Prieto and the Hawaiian Geothermal project have been history matched. Using these well tests as a base, the influence of reservoir permeability, porosity, thickness, and heat capacity, along with flow rate and fracturing were studied. Single and two-phase transient well test equations were used to analyze these tests with poor results due to rapidly changing fluid properties and inability to calculate the flowing steam saturation in the reservoir. The injection of cold water into the reservoir does give good data from which formation properties can be calculated. Title: Transient well testing in two-phase geothermal reservoirs Author: Aydelotte, S.R. Year: 1980 A study of well test analysis techniques in two-phase geothermal reservoirs has been conducted using a three-dimensional, two-phase, wellbore and reservoir simulation model. Well tests from Cerro Prieto and the Hawaiian Geothermal project have been history matched. Using these well tests as a base, the influence of reservoir permeability, porosity, thickness, and heat capacity, along with flow rate and fracturing were studied. Single and two-phase transient well test equations were used to analyze these tests with poor results due to rapidly changing fluid properties and inability to calculate the flowing steam saturation in the reservoir. The injection of cold water into the reservoir does give good data from which formation properties can be calculated. Close

• 2. [Image] Subsurface investigations at the Roosevelt KGRA, Utah. Final report

  	An investigation of the geothermal reservoir in the Roosevelt Hot Springs Known Geothermal Resource Area in Utah was carried out. The objective of this effort was to develop predictions for well production ...
  	Citation × Citation Citation Abstract Copy Title: Subsurface investigations at the Roosevelt KGRA, Utah. Final report Author: Butz, J. Year: 1979 An investigation of the geothermal reservoir in the Roosevelt Hot Springs Known Geothermal Resource Area in Utah was carried out. The objective of this effort was to develop predictions for well production capacities, based on data taken during field tests and through use of a computer model. In turn, the production information could then be used in design optimization and economic analyses for development of the resource under study. Flow tests of a geothermal well, Utah State 14-2, were conducted. Data consisting of pressure and temperature logs as a function of depth were obtained. Maximum recorded temperature was 503/sup 0/F (262/sup 0/C) and maximum pressure, 954 psia (6.58MPa) as measured under flow conditions. Tests were run at rates up to 580,000 lb/hr (73.3 kg/sec) total flow. The information gathered during the testing was reduced and compared to results of a predictive computer model. Reservoir conditions in the Roosevelt Hot Springs KGRA are such that two-phase flow exists in the wellbore and, in some cases, also in the reservoir itself. The computer model employed in the analysis reflects current efforts to improve the state-of-the-art in the prediction of two-phase pressure drops in vertical systems. Predictions at flowrates of up to 300,000 lb/hr (38 kg/sec) matched quite well with test data, while modeling at higher flowrates (to maximum tested) showed progressively greater deviation from test data. Cause of the observed degradation is postulated to be the movement of the flash horizon into the reservoir, due to drawdown at high flowrates; DOE/ET/28389-1 Title: Subsurface investigations at the Roosevelt KGRA, Utah. Final report Author: Butz, J. Year: 1979 An investigation of the geothermal reservoir in the Roosevelt Hot Springs Known Geothermal Resource Area in Utah was carried out. The objective of this effort was to develop predictions for well production capacities, based on data taken during field tests and through use of a computer model. In turn, the production information could then be used in design optimization and economic analyses for development of the resource under study. Flow tests of a geothermal well, Utah State 14-2, were conducted. Data consisting of pressure and temperature logs as a function of depth were obtained. Maximum recorded temperature was 503/sup 0/F (262/sup 0/C) and maximum pressure, 954 psia (6.58MPa) as measured under flow conditions. Tests were run at rates up to 580,000 lb/hr (73.3 kg/sec) total flow. The information gathered during the testing was reduced and compared to results of a predictive computer model. Reservoir conditions in the Roosevelt Hot Springs KGRA are such that two-phase flow exists in the wellbore and, in some cases, also in the reservoir itself. The computer model employed in the analysis reflects current efforts to improve the state-of-the-art in the prediction of two-phase pressure drops in vertical systems. Predictions at flowrates of up to 300,000 lb/hr (38 kg/sec) matched quite well with test data, while modeling at higher flowrates (to maximum tested) showed progressively greater deviation from test data. Cause of the observed degradation is postulated to be the movement of the flash horizon into the reservoir, due to drawdown at high flowrates; DOE/ET/28389-1 Close

• 3. [Image] DHE (Downhole Heat Exchangers)

  	The use of downhole heat exchangers (DHE) for residential or commercial space and domestic water heating and other applications has several desirable features. Systems are nearly or completely passive ...
  	Citation × Citation Citation Abstract Copy Title: DHE (Downhole Heat Exchangers) Author: Culver, G. Year: 1990 The use of downhole heat exchangers (DHE) for residential or commercial space and domestic water heating and other applications has several desirable features. Systems are nearly or completely passive -- that is, no or very little geothermal water or steam is produced from the well either reducing or completely eliminating surface environmental concerns and the need for disposal systems or injection wells. Initial cost of pumps and installation are eliminated or reduced along with pumping power costs and maintenance costs associated with pumping often corrosive geothermal fluids. Many residential and small commercial systems do not require circulating pumps because the density difference in the incoming and outgoing sides of the loop are sufficient to overcome circulating friction losses in the entire system. The major disadvantage of DHEs is their dependence on natural heat flow. In areas where geological conditions provide high permeability and a natural hydraulic gradient, DHEs can provide a substantial quantity of heat. A single 500-ft (152 m) well in Klamath Falls, Oregon, supplies over one megawatt thermal and output is apparently limited by the surface area of pipe that can be installed in the well bore. In contrast, DHEs used in conjunction with heat pumps may supply less than 8 KW from a well of similar depth. Here output is limited by conductive heat flow with perhaps a small contribution from convection near the well bore. The highest capacity DHE reported to date, in Turkey, supplies 6 MW thermal from an 820-ft (250 m) well. There were two main goals for this project. The first was to gather, disseminate and exchange internationally information on DHEs. The second was to perform experiments that would provide insight into well bore/aquifer interaction and thereby provide more information on which to base DHE designs. 27 refs., 31 figs., 3 tabs. Title: DHE (Downhole Heat Exchangers) Author: Culver, G. Year: 1990 The use of downhole heat exchangers (DHE) for residential or commercial space and domestic water heating and other applications has several desirable features. Systems are nearly or completely passive -- that is, no or very little geothermal water or steam is produced from the well either reducing or completely eliminating surface environmental concerns and the need for disposal systems or injection wells. Initial cost of pumps and installation are eliminated or reduced along with pumping power costs and maintenance costs associated with pumping often corrosive geothermal fluids. Many residential and small commercial systems do not require circulating pumps because the density difference in the incoming and outgoing sides of the loop are sufficient to overcome circulating friction losses in the entire system. The major disadvantage of DHEs is their dependence on natural heat flow. In areas where geological conditions provide high permeability and a natural hydraulic gradient, DHEs can provide a substantial quantity of heat. A single 500-ft (152 m) well in Klamath Falls, Oregon, supplies over one megawatt thermal and output is apparently limited by the surface area of pipe that can be installed in the well bore. In contrast, DHEs used in conjunction with heat pumps may supply less than 8 KW from a well of similar depth. Here output is limited by conductive heat flow with perhaps a small contribution from convection near the well bore. The highest capacity DHE reported to date, in Turkey, supplies 6 MW thermal from an 820-ft (250 m) well. There were two main goals for this project. The first was to gather, disseminate and exchange internationally information on DHEs. The second was to perform experiments that would provide insight into well bore/aquifer interaction and thereby provide more information on which to base DHE designs. 27 refs., 31 figs., 3 tabs. Close