Search

Search Results

• 1. [Image] Geothermal Resource Exploration in Boise, Idaho

  	Exploratory drilling in Boise, Idaho, in the vicinity of the Boise Front Fault has confirmed the presence of a 170/sup 0/F (77/sup 0/C) geothermal resource below about 800 ft (244 m) near the Veterans ...
  	Citation × Citation Citation Abstract Copy Title: Geothermal Resource Exploration in Boise, Idaho Author: Nelson, L.B. Year: 1980 Exploratory drilling in Boise, Idaho, in the vicinity of the Boise Front Fault has confirmed the presence of a 170/sup 0/F (77/sup 0/C) geothermal resource below about 800 ft (244 m) near the Veterans Hospital of the Military Reserve Park. The Idaho National Engineering Laboratory (INEL), sponsored by the Department of Energy, drilled three exploratory slim holes and two deep exploratory test wells. Study results based on tests of the two exploratory-test wells are reported. Faulting related to the Boise Front Fault defines a major physiographic break in the area that acts as a subsurface conduit through which geothermal water circulates. Hydrologic tests indicate that rocks disturbed by the Boise Front Fault may be as much as ten times more permeable than those removed from the major structural lineament Title: Geothermal Resource Exploration in Boise, Idaho Author: Nelson, L.B. Year: 1980 Exploratory drilling in Boise, Idaho, in the vicinity of the Boise Front Fault has confirmed the presence of a 170/sup 0/F (77/sup 0/C) geothermal resource below about 800 ft (244 m) near the Veterans Hospital of the Military Reserve Park. The Idaho National Engineering Laboratory (INEL), sponsored by the Department of Energy, drilled three exploratory slim holes and two deep exploratory test wells. Study results based on tests of the two exploratory-test wells are reported. Faulting related to the Boise Front Fault defines a major physiographic break in the area that acts as a subsurface conduit through which geothermal water circulates. Hydrologic tests indicate that rocks disturbed by the Boise Front Fault may be as much as ten times more permeable than those removed from the major structural lineament Close

• 2. [Image] Geothermal direct applications hardware systems development and testing: 1979 summary report

  	Activities performed during calendar year 1979 for the hardware system development and testing task are presented. The fluidized bed technology was applied to the drying of potato by-products and to the ...
  	Citation × Citation Citation Abstract Copy Title: Geothermal direct applications hardware systems development and testing: 1979 summary report Author: Keller, J.G. Year: 1980 Activities performed during calendar year 1979 for the hardware system development and testing task are presented. The fluidized bed technology was applied to the drying of potato by-products and to the exchange of heat to air in the space heating experiment. Geothermal water was flashed to steam and also used as the prime energy source in the steam distillation of peppermint oil. Geothermal water temperatures as low as 112.8/sup 0/C were utilized to distill alcohol from sugar beet juice, and lower temperature water provided air conditioning through an absorption air conditioning system. These experiments are discussed; EGG-2013 Title: Geothermal direct applications hardware systems development and testing: 1979 summary report Author: Keller, J.G. Year: 1980 Activities performed during calendar year 1979 for the hardware system development and testing task are presented. The fluidized bed technology was applied to the drying of potato by-products and to the exchange of heat to air in the space heating experiment. Geothermal water was flashed to steam and also used as the prime energy source in the steam distillation of peppermint oil. Geothermal water temperatures as low as 112.8/sup 0/C were utilized to distill alcohol from sugar beet juice, and lower temperature water provided air conditioning through an absorption air conditioning system. These experiments are discussed; EGG-2013 Close

• 3. [Image] Testing Operations Plan: Coso Geothermal Exploratory Hole No. 1 (CGEH-1)

  	Coso Geothermal Exploratory Hole No. 1 (CGEH-1) was drilled to investigate the potential of the Coso Hot Springs Known Geothermal Resource Area (KGRA) in southeastern California. Detailed background information ...
  	Citation × Citation Citation Abstract Copy Title: Testing Operations Plan: Coso Geothermal Exploratory Hole No. 1 (CGEH-1) Author: Nevada Operations Office; Naval Weapons Center, China Lake Year: 1978 Coso Geothermal Exploratory Hole No. 1 (CGEH-1) was drilled to investigate the potential of the Coso Hot Springs Known Geothermal Resource Area (KGRA) in southeastern California. Detailed background information is contained in the drilling plan, ''Coso Geothermal Exploratory Hole No. 1 (CGEH-1),'' NVO-184, dated June 1977. The purpose of this supplement to NVO-184 is to establish a plan of operations for testing the resource after completion of well drilling activities. Major elements of this plan include setting forth the management and organizational concept to be followed, describing the generalized site activities required and the well testing operations, and establishing schedules, environmental considerations, and technical documentation requirements. The objective of this testing is to determine the well productivity and geothermal reservoir parameters. The testing will consist of both static and dynamic measurements. The static measurements will include wellhead pressure monitoring plus downhole temperature and pressure surveys conducted with the well shut in. The dynamic measurements will include downhole and surface pressure, temperature, and flow rate data with the well producing at varying rates. Two types of dynamic tests are contemplated; the first utilizing the James Method and the second utilizing a separator test system, if justified by an evaluation of the resource potential Title: Testing Operations Plan: Coso Geothermal Exploratory Hole No. 1 (CGEH-1) Author: Nevada Operations Office; Naval Weapons Center, China Lake Year: 1978 Coso Geothermal Exploratory Hole No. 1 (CGEH-1) was drilled to investigate the potential of the Coso Hot Springs Known Geothermal Resource Area (KGRA) in southeastern California. Detailed background information is contained in the drilling plan, ''Coso Geothermal Exploratory Hole No. 1 (CGEH-1),'' NVO-184, dated June 1977. The purpose of this supplement to NVO-184 is to establish a plan of operations for testing the resource after completion of well drilling activities. Major elements of this plan include setting forth the management and organizational concept to be followed, describing the generalized site activities required and the well testing operations, and establishing schedules, environmental considerations, and technical documentation requirements. The objective of this testing is to determine the well productivity and geothermal reservoir parameters. The testing will consist of both static and dynamic measurements. The static measurements will include wellhead pressure monitoring plus downhole temperature and pressure surveys conducted with the well shut in. The dynamic measurements will include downhole and surface pressure, temperature, and flow rate data with the well producing at varying rates. Two types of dynamic tests are contemplated; the first utilizing the James Method and the second utilizing a separator test system, if justified by an evaluation of the resource potential Close

• 4. [Image] Investigation and evaluation of geopressured-geothermal wells. Fairfax Foster Sutter No. 2 well, St. Mary Parish, Louisiana. Volume I. Completion and testing. Final report

  	The Fairfax Foster Sutter No. 2 well, located in the East Franklin area of St. Mary Parish, Louisiana, is the first successful test of a geopressured-geothermal aquifer under the Well-of-Opportunity program. ...
  	Citation × Citation Citation Abstract Copy Title: Investigation and evaluation of geopressured-geothermal wells. Fairfax Foster Sutter No. 2 well, St. Mary Parish, Louisiana. Volume I. Completion and testing. Final report Author: Willits, M.H. Year: 1979 The Fairfax Foster Sutter No. 2 well, located in the East Franklin area of St. Mary Parish, Louisiana, is the first successful test of a geopressured-geothermal aquifer under the Well-of-Opportunity program. The section tested was the MA-6 sand of lower Miocene age which has produced large quantities of gas from the adjacent but structurally separated Garden City field. In the subject well the observed temperature was 270{sup 0}F (132{sup 0}C) and the measured gradient was 0.77 psi/ft. The gross sand thickness was 270 feet, the net sand thickness 190 feet, and the tested interval 58 net feet. The temperatures and pressures encountered approached the limits of the surface-recording bottomhole pressure gauge and particularly the single-conductor cables on which the gauges were run. The objectives of the tests were all accomplished, and data were obtained which will contribute to the overall assessment of the geopressured-geothermal resource of the Upper Gulf of Mexico basin. In general, the gas solubility (22.8 scf/bbl) was as expected for the temperature, pressure, and salinity of the brine. The produced water was more saline than expected (160,000 mg/l). The high concentrations of dissolved solids, coupled with the evolution of CO{sub 2} from these waters during production, created a scaling problem in the tubular goods and surface equipment that will have to be addressed in future tests; DOE/ET/28460-1 Title: Investigation and evaluation of geopressured-geothermal wells. Fairfax Foster Sutter No. 2 well, St. Mary Parish, Louisiana. Volume I. Completion and testing. Final report Author: Willits, M.H. Year: 1979 The Fairfax Foster Sutter No. 2 well, located in the East Franklin area of St. Mary Parish, Louisiana, is the first successful test of a geopressured-geothermal aquifer under the Well-of-Opportunity program. The section tested was the MA-6 sand of lower Miocene age which has produced large quantities of gas from the adjacent but structurally separated Garden City field. In the subject well the observed temperature was 270{sup 0}F (132{sup 0}C) and the measured gradient was 0.77 psi/ft. The gross sand thickness was 270 feet, the net sand thickness 190 feet, and the tested interval 58 net feet. The temperatures and pressures encountered approached the limits of the surface-recording bottomhole pressure gauge and particularly the single-conductor cables on which the gauges were run. The objectives of the tests were all accomplished, and data were obtained which will contribute to the overall assessment of the geopressured-geothermal resource of the Upper Gulf of Mexico basin. In general, the gas solubility (22.8 scf/bbl) was as expected for the temperature, pressure, and salinity of the brine. The produced water was more saline than expected (160,000 mg/l). The high concentrations of dissolved solids, coupled with the evolution of CO{sub 2} from these waters during production, created a scaling problem in the tubular goods and surface equipment that will have to be addressed in future tests; DOE/ET/28460-1 Close

• 5. [Image] Subsurface investigations at the Roosevelt KGRA, Utah. Final report

  	An investigation of the geothermal reservoir in the Roosevelt Hot Springs Known Geothermal Resource Area in Utah was carried out. The objective of this effort was to develop predictions for well production ...
  	Citation × Citation Citation Abstract Copy Title: Subsurface investigations at the Roosevelt KGRA, Utah. Final report Author: Butz, J. Year: 1979 An investigation of the geothermal reservoir in the Roosevelt Hot Springs Known Geothermal Resource Area in Utah was carried out. The objective of this effort was to develop predictions for well production capacities, based on data taken during field tests and through use of a computer model. In turn, the production information could then be used in design optimization and economic analyses for development of the resource under study. Flow tests of a geothermal well, Utah State 14-2, were conducted. Data consisting of pressure and temperature logs as a function of depth were obtained. Maximum recorded temperature was 503/sup 0/F (262/sup 0/C) and maximum pressure, 954 psia (6.58MPa) as measured under flow conditions. Tests were run at rates up to 580,000 lb/hr (73.3 kg/sec) total flow. The information gathered during the testing was reduced and compared to results of a predictive computer model. Reservoir conditions in the Roosevelt Hot Springs KGRA are such that two-phase flow exists in the wellbore and, in some cases, also in the reservoir itself. The computer model employed in the analysis reflects current efforts to improve the state-of-the-art in the prediction of two-phase pressure drops in vertical systems. Predictions at flowrates of up to 300,000 lb/hr (38 kg/sec) matched quite well with test data, while modeling at higher flowrates (to maximum tested) showed progressively greater deviation from test data. Cause of the observed degradation is postulated to be the movement of the flash horizon into the reservoir, due to drawdown at high flowrates; DOE/ET/28389-1 Title: Subsurface investigations at the Roosevelt KGRA, Utah. Final report Author: Butz, J. Year: 1979 An investigation of the geothermal reservoir in the Roosevelt Hot Springs Known Geothermal Resource Area in Utah was carried out. The objective of this effort was to develop predictions for well production capacities, based on data taken during field tests and through use of a computer model. In turn, the production information could then be used in design optimization and economic analyses for development of the resource under study. Flow tests of a geothermal well, Utah State 14-2, were conducted. Data consisting of pressure and temperature logs as a function of depth were obtained. Maximum recorded temperature was 503/sup 0/F (262/sup 0/C) and maximum pressure, 954 psia (6.58MPa) as measured under flow conditions. Tests were run at rates up to 580,000 lb/hr (73.3 kg/sec) total flow. The information gathered during the testing was reduced and compared to results of a predictive computer model. Reservoir conditions in the Roosevelt Hot Springs KGRA are such that two-phase flow exists in the wellbore and, in some cases, also in the reservoir itself. The computer model employed in the analysis reflects current efforts to improve the state-of-the-art in the prediction of two-phase pressure drops in vertical systems. Predictions at flowrates of up to 300,000 lb/hr (38 kg/sec) matched quite well with test data, while modeling at higher flowrates (to maximum tested) showed progressively greater deviation from test data. Cause of the observed degradation is postulated to be the movement of the flash horizon into the reservoir, due to drawdown at high flowrates; DOE/ET/28389-1 Close

• 6. [Image] Geothermal Resource and Reservoir Investigations of U. S. Bureau of Reclamation Leaseholds at East Mesa, Imperial Valley, California

  	The study included five parts: geology, seismicity, well testing, reservoir simulation, and geochemistry. Included in appendices are: production test data and discussion, interference tests, production ...
  	Citation × Citation Citation Abstract Copy Title: Geothermal Resource and Reservoir Investigations of U. S. Bureau of Reclamation Leaseholds at East Mesa, Imperial Valley, California Author: Howard, J. Year: 1978 The study included five parts: geology, seismicity, well testing, reservoir simulation, and geochemistry. Included in appendices are: production test data and discussion, interference tests, production tests in the northern portion of the East Mesa KGRA, conversion tables, chemical analysis of fluids from East Mesa wells, and results of laboratory studies of scale samples taken from the vertical tube evaporator. (MHR) Title: Geothermal Resource and Reservoir Investigations of U. S. Bureau of Reclamation Leaseholds at East Mesa, Imperial Valley, California Author: Howard, J. Year: 1978 The study included five parts: geology, seismicity, well testing, reservoir simulation, and geochemistry. Included in appendices are: production test data and discussion, interference tests, production tests in the northern portion of the East Mesa KGRA, conversion tables, chemical analysis of fluids from East Mesa wells, and results of laboratory studies of scale samples taken from the vertical tube evaporator. (MHR) Close

• 7. [Image] Transient well testing in two-phase geothermal reservoirs

  	A study of well test analysis techniques in two-phase geothermal reservoirs has been conducted using a three-dimensional, two-phase, wellbore and reservoir simulation model. Well tests from Cerro Prieto ...
  	Citation × Citation Citation Abstract Copy Title: Transient well testing in two-phase geothermal reservoirs Author: Aydelotte, S.R. Year: 1980 A study of well test analysis techniques in two-phase geothermal reservoirs has been conducted using a three-dimensional, two-phase, wellbore and reservoir simulation model. Well tests from Cerro Prieto and the Hawaiian Geothermal project have been history matched. Using these well tests as a base, the influence of reservoir permeability, porosity, thickness, and heat capacity, along with flow rate and fracturing were studied. Single and two-phase transient well test equations were used to analyze these tests with poor results due to rapidly changing fluid properties and inability to calculate the flowing steam saturation in the reservoir. The injection of cold water into the reservoir does give good data from which formation properties can be calculated. Title: Transient well testing in two-phase geothermal reservoirs Author: Aydelotte, S.R. Year: 1980 A study of well test analysis techniques in two-phase geothermal reservoirs has been conducted using a three-dimensional, two-phase, wellbore and reservoir simulation model. Well tests from Cerro Prieto and the Hawaiian Geothermal project have been history matched. Using these well tests as a base, the influence of reservoir permeability, porosity, thickness, and heat capacity, along with flow rate and fracturing were studied. Single and two-phase transient well test equations were used to analyze these tests with poor results due to rapidly changing fluid properties and inability to calculate the flowing steam saturation in the reservoir. The injection of cold water into the reservoir does give good data from which formation properties can be calculated. Close