Search

Search Results

• 1. [Image] Stratigraphy and Alteration, 15 Shallow Thermal Gradient Holes, Roosevelt Hot Springs KGRA and Vicinity, Millard and Beaver Counties, Utah

  	Fifteen shallow thermal gradient drill holes were recently completed by Geothermal Power Corporation (GPCR) in the vicinity of the Roosevelt Hot Springs KGRA. Five holes penetrated Tertiary granitic rocks ...
  	Citation × Citation Citation Abstract Copy Title: Stratigraphy and Alteration, 15 Shallow Thermal Gradient Holes, Roosevelt Hot Springs KGRA and Vicinity, Millard and Beaver Counties, Utah Author: Hulen, J.B. Year: 1978 Fifteen shallow thermal gradient drill holes were recently completed by Geothermal Power Corporation (GPCR) in the vicinity of the Roosevelt Hot Springs KGRA. Five holes penetrated Tertiary granitic rocks and Precambrian gneiss east of the KGRA. Seven holes completed entirely in alluvium near the southwestern corner of the KGRA encountered a near-surface marker horizon of Pleistocene pumice and perlite. Maximum calculated alluvial sedimentation rates since initial deposition of this pumice and perlite range from 1 foot in 12,500 years to 1 foot in 2,300 years. Three holes east of the Mineral Mountains penetrated late Cenozoic basaltic andesite beneath a thin veneer of alluvium. All 15 GPCR drill holes appear to be peripheral to a central zone of anomalously high thermal gradient and low resisitivity delineated by previous investigations. GPCR-8 and -14, however, are characterized by high heat flow and relatively abundant manganese oxide mineralization, which may reflect a favorable hydrologic system controlling thermal fluid flow at depth. These holes thus seem most encouraging for discovery of a deeper high-temperature geothermal resource Title: Stratigraphy and Alteration, 15 Shallow Thermal Gradient Holes, Roosevelt Hot Springs KGRA and Vicinity, Millard and Beaver Counties, Utah Author: Hulen, J.B. Year: 1978 Fifteen shallow thermal gradient drill holes were recently completed by Geothermal Power Corporation (GPCR) in the vicinity of the Roosevelt Hot Springs KGRA. Five holes penetrated Tertiary granitic rocks and Precambrian gneiss east of the KGRA. Seven holes completed entirely in alluvium near the southwestern corner of the KGRA encountered a near-surface marker horizon of Pleistocene pumice and perlite. Maximum calculated alluvial sedimentation rates since initial deposition of this pumice and perlite range from 1 foot in 12,500 years to 1 foot in 2,300 years. Three holes east of the Mineral Mountains penetrated late Cenozoic basaltic andesite beneath a thin veneer of alluvium. All 15 GPCR drill holes appear to be peripheral to a central zone of anomalously high thermal gradient and low resisitivity delineated by previous investigations. GPCR-8 and -14, however, are characterized by high heat flow and relatively abundant manganese oxide mineralization, which may reflect a favorable hydrologic system controlling thermal fluid flow at depth. These holes thus seem most encouraging for discovery of a deeper high-temperature geothermal resource Close

• 2. [Image] Evaluation and Targeting of Geothermal Energy Resources in the Southeastern United States Progress Report, Apr 1, 1977--Jun 30, 1977

  	The objective of this research is to develop and apply targeting procedures for the evaluation of low-temperature radiogenically-derived geothermal resources in the eastern United States utilizing geological, ...
  	Citation × Citation Citation Abstract Copy Title: Evaluation and Targeting of Geothermal Energy Resources in the Southeastern United States Progress Report, Apr 1, 1977--Jun 30, 1977 Author: Costain, J.K. Year: 1977 The objective of this research is to develop and apply targeting procedures for the evaluation of low-temperature radiogenically-derived geothermal resources in the eastern United States utilizing geological, geochemical, and geophysical data. Detailed study of the Winnsboro complex, South Carolina, is continuing as part of a broader project to provide insight into the behavior of uranium and thorium in syn- and postmetamorphic granitic plutons Title: Evaluation and Targeting of Geothermal Energy Resources in the Southeastern United States Progress Report, Apr 1, 1977--Jun 30, 1977 Author: Costain, J.K. Year: 1977 The objective of this research is to develop and apply targeting procedures for the evaluation of low-temperature radiogenically-derived geothermal resources in the eastern United States utilizing geological, geochemical, and geophysical data. Detailed study of the Winnsboro complex, South Carolina, is continuing as part of a broader project to provide insight into the behavior of uranium and thorium in syn- and postmetamorphic granitic plutons Close

• 3. [Image] Thermal Gradient and Heat Flow Drilling, Volume 5, Final Report

  	During the summer of 1975, the Department of Geology and Geophysics drilled nine drill thermal gradient/heat flow holes. Total footage drilled was 2125 feet. Seven holes were drilled with a Mayhew 1000 ...
  	Citation × Citation Citation Abstract Copy Title: Thermal Gradient and Heat Flow Drilling, Volume 5, Final Report Author: Whelan, J.A. Year: 1977 During the summer of 1975, the Department of Geology and Geophysics drilled nine drill thermal gradient/heat flow holes. Total footage drilled was 2125 feet. Seven holes were drilled with a Mayhew 1000 drill using various combinations of down the hole hammer drilling, rotary drilling, and NX diamond core drilling. Three of these were heat flow holes--one in the Mineral Range, one in the Tushar Range near Beaver, Utah, and one near Monroe, Utah. Two were alteration study holes in the Roosevelt KGRA and two were temperature gradient holes, in alluvium in the Roosevelt KGRA. The average depth of the holes drilled with the Mayhew 1000 drill was 247 feet. Holes ranged from 135 feet to 492 feet. Cost per foot averaged $18.53. Two holes were core drilled with a Joy 12, BX-size drill. One was to 75 feet, in perlite. This hole was abandoned. The other was to 323 feet in granite. These holes averaged $13.82 per foot. Permission to drill was obtained from BLM and drill sites were inspected with BLM personnel to avoid disturbing archeological sites. Sites were reseeded where disturbed. Holes were completed by setting capped one-inch black iron pipe, backfilling the hole with cuttings to 10 feet from surface and cementing to the surface Title: Thermal Gradient and Heat Flow Drilling, Volume 5, Final Report Author: Whelan, J.A. Year: 1977 During the summer of 1975, the Department of Geology and Geophysics drilled nine drill thermal gradient/heat flow holes. Total footage drilled was 2125 feet. Seven holes were drilled with a Mayhew 1000 drill using various combinations of down the hole hammer drilling, rotary drilling, and NX diamond core drilling. Three of these were heat flow holes--one in the Mineral Range, one in the Tushar Range near Beaver, Utah, and one near Monroe, Utah. Two were alteration study holes in the Roosevelt KGRA and two were temperature gradient holes, in alluvium in the Roosevelt KGRA. The average depth of the holes drilled with the Mayhew 1000 drill was 247 feet. Holes ranged from 135 feet to 492 feet. Cost per foot averaged $18.53. Two holes were core drilled with a Joy 12, BX-size drill. One was to 75 feet, in perlite. This hole was abandoned. The other was to 323 feet in granite. These holes averaged $13.82 per foot. Permission to drill was obtained from BLM and drill sites were inspected with BLM personnel to avoid disturbing archeological sites. Sites were reseeded where disturbed. Holes were completed by setting capped one-inch black iron pipe, backfilling the hole with cuttings to 10 feet from surface and cementing to the surface Close

• 4. [Image] Downhole Electrical Detection of Hydraulic Fractures in GT-2 and EE-1

  	Electrical geophysical methods including mise a la masse and self-potential (SP) for determination of hydraulic fracture characteristics were used at the hot dry rock geothermal project. Electrical and ...
  	Citation × Citation Citation Abstract Copy Title: Downhole Electrical Detection of Hydraulic Fractures in GT-2 and EE-1 Author: Kintzinger, P.R. Year: 1977 Electrical geophysical methods including mise a la masse and self-potential (SP) for determination of hydraulic fracture characteristics were used at the hot dry rock geothermal project. Electrical and induction logs indicated that the resistivity contrast between the granite and 200/sup 0/C water at the 2926-m (9600-ft) depth is a factor of 1000 or more. Thus the water in a hydraulic fracture, formed to connect two adjacent deep holes, is a good conductor compared to the confining granite. Mise a la masse-type measurements were made to help determine the characteristics for hydraulic fractures formed in each of the two geothermal holes GT-2 and EE-1. Once a hydraulic fracture has been formed, mise a la masse effects are obtained both with the fracture pressurized above hydrostatic and when depressurized to hydrostatic. This indicates that once the fracture has been created, enough natural propping exists that a conductive zone persists even when the fracture is deflated. A fracture was formed in a 18-m (60-ft) zone immediately below 1957 m (6420 ft) in EE-1. Later a set of SP logs was run in this zone with no pressure, with pressure building, with pressure decreasing, and again with the fracture depressurized. Results show that during times of change of parameters in hydraulically fractured regions in the hole, natural SP logging helps to determine the position of the fracture. However, after a fracture has come to equilibrium with fluid parameters such as temperature, pressure, salinity, and pH, an effect of the fracture may not be evident. Self-potential logs provide an excellent method for locating the bottom of steel casing that has been set in the hole Title: Downhole Electrical Detection of Hydraulic Fractures in GT-2 and EE-1 Author: Kintzinger, P.R. Year: 1977 Electrical geophysical methods including mise a la masse and self-potential (SP) for determination of hydraulic fracture characteristics were used at the hot dry rock geothermal project. Electrical and induction logs indicated that the resistivity contrast between the granite and 200/sup 0/C water at the 2926-m (9600-ft) depth is a factor of 1000 or more. Thus the water in a hydraulic fracture, formed to connect two adjacent deep holes, is a good conductor compared to the confining granite. Mise a la masse-type measurements were made to help determine the characteristics for hydraulic fractures formed in each of the two geothermal holes GT-2 and EE-1. Once a hydraulic fracture has been formed, mise a la masse effects are obtained both with the fracture pressurized above hydrostatic and when depressurized to hydrostatic. This indicates that once the fracture has been created, enough natural propping exists that a conductive zone persists even when the fracture is deflated. A fracture was formed in a 18-m (60-ft) zone immediately below 1957 m (6420 ft) in EE-1. Later a set of SP logs was run in this zone with no pressure, with pressure building, with pressure decreasing, and again with the fracture depressurized. Results show that during times of change of parameters in hydraulically fractured regions in the hole, natural SP logging helps to determine the position of the fracture. However, after a fracture has come to equilibrium with fluid parameters such as temperature, pressure, salinity, and pH, an effect of the fracture may not be evident. Self-potential logs provide an excellent method for locating the bottom of steel casing that has been set in the hole Close

• 5. [Image] Preliminary Petrographic and Geophysical Interpretations of the Exploratory Geothermal Drill Hole and Core, Redstone, New Hampshire

  	A 3000 foot diamond drill hole was drilled in the Conway Granite in Redstone, New Hampshire. A comprehensive detailed petrographic and physical study of this core was made. The purpose of this study is ...
  	Citation × Citation Citation Abstract Copy Title: Preliminary Petrographic and Geophysical Interpretations of the Exploratory Geothermal Drill Hole and Core, Redstone, New Hampshire Author: Hoag, R.B. Jr. Year: 1977 A 3000 foot diamond drill hole was drilled in the Conway Granite in Redstone, New Hampshire. A comprehensive detailed petrographic and physical study of this core was made. The purpose of this study is to supply a sound data base for future geothermal and uranium-thorium studies of the drill core. An estimate of the heat flow potential of the Redstone drill hole gives a heat flow of 1.9 HFU. If only the red phase of the Conway Granite had been intersected the heat flow may have been as much as 2.7 HFU, reaching a temperature of 260/sup 0/C at 6 km. The drill hole intersected four lithologies; the green and red phase of the Conway Granite, the Albany quartz syenite and a medium-grained, hastingsite-biotite granite. The red phase has the highest and most irregular radioactivity. The irregularity is mainly due to minor variations in lithology. The Drill core intersected several alteration zones up to a thickness of 150 feet. These alteration zones represent passage of low to medium temperature fluids which might have been mineralized. The Conway Granite has the physical and chemical characteristics necessary for the formation of vein type uranium deposits. The presence of unexplained radiometric anomalies lends support to the existence of such deposits Title: Preliminary Petrographic and Geophysical Interpretations of the Exploratory Geothermal Drill Hole and Core, Redstone, New Hampshire Author: Hoag, R.B. Jr. Year: 1977 A 3000 foot diamond drill hole was drilled in the Conway Granite in Redstone, New Hampshire. A comprehensive detailed petrographic and physical study of this core was made. The purpose of this study is to supply a sound data base for future geothermal and uranium-thorium studies of the drill core. An estimate of the heat flow potential of the Redstone drill hole gives a heat flow of 1.9 HFU. If only the red phase of the Conway Granite had been intersected the heat flow may have been as much as 2.7 HFU, reaching a temperature of 260/sup 0/C at 6 km. The drill hole intersected four lithologies; the green and red phase of the Conway Granite, the Albany quartz syenite and a medium-grained, hastingsite-biotite granite. The red phase has the highest and most irregular radioactivity. The irregularity is mainly due to minor variations in lithology. The Drill core intersected several alteration zones up to a thickness of 150 feet. These alteration zones represent passage of low to medium temperature fluids which might have been mineralized. The Conway Granite has the physical and chemical characteristics necessary for the formation of vein type uranium deposits. The presence of unexplained radiometric anomalies lends support to the existence of such deposits Close