Search

Search Results

• 1. [Image] Fluid-Temperature Logs for Selected Wells in Eastern Washington

  	This Open-File Report consists of fluid temperature logs compiled during studies of the geohydrology and low temperature geothermal resources of eastern Washington. The fluid temperature logs are divided ...
  	Citation × Citation Citation Abstract Copy Title: Fluid-Temperature Logs for Selected Wells in Eastern Washington Author: Stoffel, K. L. Year: 1983 This Open-File Report consists of fluid temperature logs compiled during studies of the geohydrology and low temperature geothermal resources of eastern Washington. The fluid temperature logs are divided into two groups. Part A consists of wells which are concentrated in the Moses Lake-Ritzville-Connell area. Full geophysical log suites for many of these wells are presented in Stoffel and Widness (1983) and discussed in Widness (1983, 1984). Part B consists of wells outside of the Moses Lake-Ritzville-Connell study area Title: Fluid-Temperature Logs for Selected Wells in Eastern Washington Author: Stoffel, K. L. Year: 1983 This Open-File Report consists of fluid temperature logs compiled during studies of the geohydrology and low temperature geothermal resources of eastern Washington. The fluid temperature logs are divided into two groups. Part A consists of wells which are concentrated in the Moses Lake-Ritzville-Connell area. Full geophysical log suites for many of these wells are presented in Stoffel and Widness (1983) and discussed in Widness (1983, 1984). Part B consists of wells outside of the Moses Lake-Ritzville-Connell study area Close

• 2. [Image] Neutron Formation Temperature Gauge and Neutron Activation Analysis Brine Flow Meter. Final Report, October 1, 1976--March 31, 1978

  	Feasibility studies of nuclear techniques applicable to the determination of geothermal formation temperature and two-phase brine flow downhole have been performed. The formation temperature gauging technique ...
  	Citation × Citation Citation Abstract Copy Title: Neutron Formation Temperature Gauge and Neutron Activation Analysis Brine Flow Meter. Final Report, October 1, 1976--March 31, 1978 Author: Vagelatos, N. Year: 1978 Feasibility studies of nuclear techniques applicable to the determination of geothermal formation temperature and two-phase brine flow downhole have been performed. The formation temperature gauging technique involves injection of fast neutrons into the formation and analysis of the moderated slow neutron energy distribution by appropriately filtered neutron detectors. The scientific feasibility of the method has been demonstrated by analytical computational and experimental evaluation of the system response. A data analysis method has been developed to determine unambiguously the temperature, neutron absorption cross section and neutron moderating power of an arbitrary medium. The initial phase of a program to demonstrate the engineering feasibility of the technique has been performed. A sonde mockup was fabricated and measurements have been performed in a test stand designed to simulate a geothermal well. The results indicate that the formation temperature determined by this method is independent of differences between the temperature in the borehole fluid and the formation, borehole fluid density, and borehole fluid salinity. Estimates of performance specifications for a formation temperature sonde have been made on the basis of information obtained in this study and a conceptual design of a logging system has been developed. The technique for the determination of fluid flow in a well is based on neutron activation analysis of elements present in the brine. An analytical evaluation of the method has been performed. The results warrant further, experimental evaluation Title: Neutron Formation Temperature Gauge and Neutron Activation Analysis Brine Flow Meter. Final Report, October 1, 1976--March 31, 1978 Author: Vagelatos, N. Year: 1978 Feasibility studies of nuclear techniques applicable to the determination of geothermal formation temperature and two-phase brine flow downhole have been performed. The formation temperature gauging technique involves injection of fast neutrons into the formation and analysis of the moderated slow neutron energy distribution by appropriately filtered neutron detectors. The scientific feasibility of the method has been demonstrated by analytical computational and experimental evaluation of the system response. A data analysis method has been developed to determine unambiguously the temperature, neutron absorption cross section and neutron moderating power of an arbitrary medium. The initial phase of a program to demonstrate the engineering feasibility of the technique has been performed. A sonde mockup was fabricated and measurements have been performed in a test stand designed to simulate a geothermal well. The results indicate that the formation temperature determined by this method is independent of differences between the temperature in the borehole fluid and the formation, borehole fluid density, and borehole fluid salinity. Estimates of performance specifications for a formation temperature sonde have been made on the basis of information obtained in this study and a conceptual design of a logging system has been developed. The technique for the determination of fluid flow in a well is based on neutron activation analysis of elements present in the brine. An analytical evaluation of the method has been performed. The results warrant further, experimental evaluation Close

• 3. [Image] Static Downhole Characteristics of Well CGEH-1 at Coso Hot Springs, China Lake, California

  	A series of measurements was made in the exploratory well CGEH-1 at Coso Hot Springs. The temperature measurements provide estimates for the thermal equilibration of the well and indicate that the fractures ...
  	Citation × Citation Citation Abstract Copy Title: Static Downhole Characteristics of Well CGEH-1 at Coso Hot Springs, China Lake, California Author: Goranson, C. Year: 1978 A series of measurements was made in the exploratory well CGEH-1 at Coso Hot Springs. The temperature measurements provide estimates for the thermal equilibration of the well and indicate that the fractures intersecting the well have different temperatures. The hottest fractures are in the upper-cased portion of the well. Downhole chemical sampling suggests that the borehole still contains remnants of drilling materials. The well has never been extensively flowed at this time Title: Static Downhole Characteristics of Well CGEH-1 at Coso Hot Springs, China Lake, California Author: Goranson, C. Year: 1978 A series of measurements was made in the exploratory well CGEH-1 at Coso Hot Springs. The temperature measurements provide estimates for the thermal equilibration of the well and indicate that the fractures intersecting the well have different temperatures. The hottest fractures are in the upper-cased portion of the well. Downhole chemical sampling suggests that the borehole still contains remnants of drilling materials. The well has never been extensively flowed at this time Close

• 4. [Image] Evaluation and Design of Downhole Heat Exchangers for Direct Application; Annual Report, May 1, 1976 - July 1, 1977

  	Progress in an experimental and analytical research program to evaluate and improve the design of downhole heat exchangers (DHEs) for direct applications of geothermal energy is reported. Significant progress ...
  	Citation × Citation Citation Abstract Copy Title: Evaluation and Design of Downhole Heat Exchangers for Direct Application; Annual Report, May 1, 1976 - July 1, 1977 Author: Culver, G.G. Year: 1977 Progress in an experimental and analytical research program to evaluate and improve the design of downhole heat exchangers (DHEs) for direct applications of geothermal energy is reported. Significant progress has been achieved in characterizing flows in wells and without perforated casings and DHEs installed, determination of energy extraction rates for conventional DHEs in both cased and uncased wells, and utilization of information obtained to develop and substantiate models of heat transfer within the well. Flow characterization was obtained by experimentally measuring temperature and velocity profiles. In uncased wells, there was a relatively large vertical temperature gradient (approximately 0.5{sup 0}C/m) and insignificant measured vertical flow, while for the same wells when cased the temperature gradient was essentially zero (approximately 0.03{sup 0}C/m) and a large vertically upward flow was measured (9 to 14 cm/s as measured with a hot-film anemometer). These show that a significant connection cell is established after installation of the casing. The energy extraction rates for a conventional DHE both before and after casing of a 60 m deep well was experimentally measured. In the uncased well up to 300 kW was obtained while the cased well produced over 500 kW. Analytical heat transfer models were developed for the cased well both with and without DHEs. For the cased well without a DHE, the model predicts flow rates that agree with the measured value within about 30 percent. Further, the energy extraction rates predicted by the models agree even better with the measured values. These models allow the energy extraction rates of design parameter variations to be evaluated. At this stage, only trends can be shown but with additional substantiation they should produce optimum energy extraction designs Title: Evaluation and Design of Downhole Heat Exchangers for Direct Application; Annual Report, May 1, 1976 - July 1, 1977 Author: Culver, G.G. Year: 1977 Progress in an experimental and analytical research program to evaluate and improve the design of downhole heat exchangers (DHEs) for direct applications of geothermal energy is reported. Significant progress has been achieved in characterizing flows in wells and without perforated casings and DHEs installed, determination of energy extraction rates for conventional DHEs in both cased and uncased wells, and utilization of information obtained to develop and substantiate models of heat transfer within the well. Flow characterization was obtained by experimentally measuring temperature and velocity profiles. In uncased wells, there was a relatively large vertical temperature gradient (approximately 0.5{sup 0}C/m) and insignificant measured vertical flow, while for the same wells when cased the temperature gradient was essentially zero (approximately 0.03{sup 0}C/m) and a large vertically upward flow was measured (9 to 14 cm/s as measured with a hot-film anemometer). These show that a significant connection cell is established after installation of the casing. The energy extraction rates for a conventional DHE both before and after casing of a 60 m deep well was experimentally measured. In the uncased well up to 300 kW was obtained while the cased well produced over 500 kW. Analytical heat transfer models were developed for the cased well both with and without DHEs. For the cased well without a DHE, the model predicts flow rates that agree with the measured value within about 30 percent. Further, the energy extraction rates predicted by the models agree even better with the measured values. These models allow the energy extraction rates of design parameter variations to be evaluated. At this stage, only trends can be shown but with additional substantiation they should produce optimum energy extraction designs Close

• 5. [Image] Equipment Development Report: Borehole-Fluid Sampling Tool

  	The design and development of a tool for collecting fluid samples from hot, deep geothermal boreholes are discussed. This tool has performed satisfactorily in the field at downhole temperatures of 200/sup ...
  	Citation × Citation Citation Abstract Copy Title: Equipment Development Report: Borehole-Fluid Sampling Tool Author: Archuleta, J.R. Year: 1978 The design and development of a tool for collecting fluid samples from hot, deep geothermal boreholes are discussed. This tool has performed satisfactorily in the field at downhole temperatures of 200/sup 0/C and pressures of 34.5 MPa (5000 psi). Assembly and operating instructions are included Title: Equipment Development Report: Borehole-Fluid Sampling Tool Author: Archuleta, J.R. Year: 1978 The design and development of a tool for collecting fluid samples from hot, deep geothermal boreholes are discussed. This tool has performed satisfactorily in the field at downhole temperatures of 200/sup 0/C and pressures of 34.5 MPa (5000 psi). Assembly and operating instructions are included Close

• 6. [Image] Hot Dry Rock Geothermal Energy Development Program, Annual Report, Fiscal Year 1980

  	Investigation and flow testing of the enlarged Phase I heat-extraction system at Fenton Hill continued throughout FY80. Temperature drawdown observed at that time indicated an effective fracture of approximately ...
  	Citation × Citation Citation Abstract Copy Title: Hot Dry Rock Geothermal Energy Development Program, Annual Report, Fiscal Year 1980 Author: Cremer, G.M. (comp.) Year: 1981 Investigation and flow testing of the enlarged Phase I heat-extraction system at Fenton Hill continued throughout FY80. Temperature drawdown observed at that time indicated an effective fracture of approximately 40,000 to 60,000 m/sup 2/. In May 1980, hot dry rock (HDR) technology was used to produce electricity in an interface demonstration experiment at Fenton Hill. A 60-kVA binary-cycle electrical generator was installed in the Phase I surface system and heat from about 3 kg/s of geothermal fluid at 132/sup 0/C was used to boil Freon R-114, whose vapor drove a turboalternator. A Phase II system was designed and is now being constructed at Fenton Hill that should approach commercial requirements. Borehole EE-2, the injection well, was completed on May 12, 1980. It was drilled to a vertical depth of about 4500 m, where the rock temperature is approximately 320/sup 0/C. The production well, EE-3 had been drilled to a depth of 3044 m and drilling was continuing. Environmental monitoring of Fenton Hill site continued. Development of equipment, instruments, and materials for technical support at Fenton Hill continued during FY80. Several kinds of models were also developed to understand the behavior of the Phase I system and to develop a predictive capability for future systems. Data from extensive resource investigations were collected, analyzed, and assembled into a geothermal gradient map of the US, and studies were completed on five specific areas as possible locations for HDR Experimental Site 2 Title: Hot Dry Rock Geothermal Energy Development Program, Annual Report, Fiscal Year 1980 Author: Cremer, G.M. (comp.) Year: 1981 Investigation and flow testing of the enlarged Phase I heat-extraction system at Fenton Hill continued throughout FY80. Temperature drawdown observed at that time indicated an effective fracture of approximately 40,000 to 60,000 m/sup 2/. In May 1980, hot dry rock (HDR) technology was used to produce electricity in an interface demonstration experiment at Fenton Hill. A 60-kVA binary-cycle electrical generator was installed in the Phase I surface system and heat from about 3 kg/s of geothermal fluid at 132/sup 0/C was used to boil Freon R-114, whose vapor drove a turboalternator. A Phase II system was designed and is now being constructed at Fenton Hill that should approach commercial requirements. Borehole EE-2, the injection well, was completed on May 12, 1980. It was drilled to a vertical depth of about 4500 m, where the rock temperature is approximately 320/sup 0/C. The production well, EE-3 had been drilled to a depth of 3044 m and drilling was continuing. Environmental monitoring of Fenton Hill site continued. Development of equipment, instruments, and materials for technical support at Fenton Hill continued during FY80. Several kinds of models were also developed to understand the behavior of the Phase I system and to develop a predictive capability for future systems. Data from extensive resource investigations were collected, analyzed, and assembled into a geothermal gradient map of the US, and studies were completed on five specific areas as possible locations for HDR Experimental Site 2 Close

• 7. [Image] Geothermal Resource and Reservoir Investigations of U. S. Bureau of Reclamation Leaseholds at East Mesa, Imperial Valley, California

  	The study included five parts: geology, seismicity, well testing, reservoir simulation, and geochemistry. Included in appendices are: production test data and discussion, interference tests, production ...
  	Citation × Citation Citation Abstract Copy Title: Geothermal Resource and Reservoir Investigations of U. S. Bureau of Reclamation Leaseholds at East Mesa, Imperial Valley, California Author: Howard, J. Year: 1978 The study included five parts: geology, seismicity, well testing, reservoir simulation, and geochemistry. Included in appendices are: production test data and discussion, interference tests, production tests in the northern portion of the East Mesa KGRA, conversion tables, chemical analysis of fluids from East Mesa wells, and results of laboratory studies of scale samples taken from the vertical tube evaporator. (MHR) Title: Geothermal Resource and Reservoir Investigations of U. S. Bureau of Reclamation Leaseholds at East Mesa, Imperial Valley, California Author: Howard, J. Year: 1978 The study included five parts: geology, seismicity, well testing, reservoir simulation, and geochemistry. Included in appendices are: production test data and discussion, interference tests, production tests in the northern portion of the East Mesa KGRA, conversion tables, chemical analysis of fluids from East Mesa wells, and results of laboratory studies of scale samples taken from the vertical tube evaporator. (MHR) Close

• 8. [Image] Geothermal Loop Experimental Facility. Quarterly Report, October--December 1978

  	Since the Geothermal Loop Experimental Facility (GLEF) start-up in May, 1976, a substantial amount of information has been obtained on the operation of the plant, components, brine and steam composition, ...
  	Citation × Citation Citation Abstract Copy Title: Geothermal Loop Experimental Facility. Quarterly Report, October--December 1978 Author: Anastas, G. Year: 1979 Since the Geothermal Loop Experimental Facility (GLEF) start-up in May, 1976, a substantial amount of information has been obtained on the operation of the plant, components, brine and steam composition, production and injection wells, and the potential of the Niland Reservoir. The GLEF was modified in April, 1978, from a four stage flash/binary process to a two stage cycle for the extraction of energy from a high temperature, high salinity, liquid dominated resource. This quarterly summarizes the general operations and accomplishments of the GLEF during the period from October 1, 1978 through December 31, 1978 Title: Geothermal Loop Experimental Facility. Quarterly Report, October--December 1978 Author: Anastas, G. Year: 1979 Since the Geothermal Loop Experimental Facility (GLEF) start-up in May, 1976, a substantial amount of information has been obtained on the operation of the plant, components, brine and steam composition, production and injection wells, and the potential of the Niland Reservoir. The GLEF was modified in April, 1978, from a four stage flash/binary process to a two stage cycle for the extraction of energy from a high temperature, high salinity, liquid dominated resource. This quarterly summarizes the general operations and accomplishments of the GLEF during the period from October 1, 1978 through December 31, 1978 Close