Search

Search Results

• 1. [Image] Thermal Drawdown and Recovery of Singly and Multiply Fractured Hot Dry Rock Reservoirs

  	To calculate heat extraction and thermal recovery in hot dry rock geothermal reservoirs, a computer code was written to solve the differential equations for rock-water heat conduction and convection by ...
  	Citation × Citation Citation Abstract Copy Title: Thermal Drawdown and Recovery of Singly and Multiply Fractured Hot Dry Rock Reservoirs Author: Wunder, R. Year: 1978 To calculate heat extraction and thermal recovery in hot dry rock geothermal reservoirs, a computer code was written to solve the differential equations for rock-water heat conduction and convection by finite differences. Temperature versus time functions for multiple fractures separated by various spacings are presented in dimensional and in nondimensional plots. The results were specialized for the limiting case of a single fracture in unbounded rock and for the other limiting case where the rock is so extensively fractured that thermal breakthrough phenomena can occur. Fracture temperatures were calculated during the thermal recovery following various extraction periods. For the single-fracture case these temperature recoveries could, with slight approximation, be represented as a single curve depending only upon the ratio of the total elapsed time and the extraction time Title: Thermal Drawdown and Recovery of Singly and Multiply Fractured Hot Dry Rock Reservoirs Author: Wunder, R. Year: 1978 To calculate heat extraction and thermal recovery in hot dry rock geothermal reservoirs, a computer code was written to solve the differential equations for rock-water heat conduction and convection by finite differences. Temperature versus time functions for multiple fractures separated by various spacings are presented in dimensional and in nondimensional plots. The results were specialized for the limiting case of a single fracture in unbounded rock and for the other limiting case where the rock is so extensively fractured that thermal breakthrough phenomena can occur. Fracture temperatures were calculated during the thermal recovery following various extraction periods. For the single-fracture case these temperature recoveries could, with slight approximation, be represented as a single curve depending only upon the ratio of the total elapsed time and the extraction time Close

• 2. [Image] Evaluation and Design of Downhole Heat Exchangers for Direct Application; Annual Report, May 1, 1976 - July 1, 1977

  	Progress in an experimental and analytical research program to evaluate and improve the design of downhole heat exchangers (DHEs) for direct applications of geothermal energy is reported. Significant progress ...
  	Citation × Citation Citation Abstract Copy Title: Evaluation and Design of Downhole Heat Exchangers for Direct Application; Annual Report, May 1, 1976 - July 1, 1977 Author: Culver, G.G. Year: 1977 Progress in an experimental and analytical research program to evaluate and improve the design of downhole heat exchangers (DHEs) for direct applications of geothermal energy is reported. Significant progress has been achieved in characterizing flows in wells and without perforated casings and DHEs installed, determination of energy extraction rates for conventional DHEs in both cased and uncased wells, and utilization of information obtained to develop and substantiate models of heat transfer within the well. Flow characterization was obtained by experimentally measuring temperature and velocity profiles. In uncased wells, there was a relatively large vertical temperature gradient (approximately 0.5{sup 0}C/m) and insignificant measured vertical flow, while for the same wells when cased the temperature gradient was essentially zero (approximately 0.03{sup 0}C/m) and a large vertically upward flow was measured (9 to 14 cm/s as measured with a hot-film anemometer). These show that a significant connection cell is established after installation of the casing. The energy extraction rates for a conventional DHE both before and after casing of a 60 m deep well was experimentally measured. In the uncased well up to 300 kW was obtained while the cased well produced over 500 kW. Analytical heat transfer models were developed for the cased well both with and without DHEs. For the cased well without a DHE, the model predicts flow rates that agree with the measured value within about 30 percent. Further, the energy extraction rates predicted by the models agree even better with the measured values. These models allow the energy extraction rates of design parameter variations to be evaluated. At this stage, only trends can be shown but with additional substantiation they should produce optimum energy extraction designs Title: Evaluation and Design of Downhole Heat Exchangers for Direct Application; Annual Report, May 1, 1976 - July 1, 1977 Author: Culver, G.G. Year: 1977 Progress in an experimental and analytical research program to evaluate and improve the design of downhole heat exchangers (DHEs) for direct applications of geothermal energy is reported. Significant progress has been achieved in characterizing flows in wells and without perforated casings and DHEs installed, determination of energy extraction rates for conventional DHEs in both cased and uncased wells, and utilization of information obtained to develop and substantiate models of heat transfer within the well. Flow characterization was obtained by experimentally measuring temperature and velocity profiles. In uncased wells, there was a relatively large vertical temperature gradient (approximately 0.5{sup 0}C/m) and insignificant measured vertical flow, while for the same wells when cased the temperature gradient was essentially zero (approximately 0.03{sup 0}C/m) and a large vertically upward flow was measured (9 to 14 cm/s as measured with a hot-film anemometer). These show that a significant connection cell is established after installation of the casing. The energy extraction rates for a conventional DHE both before and after casing of a 60 m deep well was experimentally measured. In the uncased well up to 300 kW was obtained while the cased well produced over 500 kW. Analytical heat transfer models were developed for the cased well both with and without DHEs. For the cased well without a DHE, the model predicts flow rates that agree with the measured value within about 30 percent. Further, the energy extraction rates predicted by the models agree even better with the measured values. These models allow the energy extraction rates of design parameter variations to be evaluated. At this stage, only trends can be shown but with additional substantiation they should produce optimum energy extraction designs Close

• 3. [Image] Fluidized-Bed Potato Waste Drying Experiments at the Raft River Geothermal Test Site

  	A fluidized-bed dryer was built and operated at the Raft River Geothermal Test Site in south central Idaho to test the feasibility of using low-temperature (145/sup 0/C or lower) geothermal fluids as an ...
  	Citation × Citation Citation Abstract Copy Title: Fluidized-Bed Potato Waste Drying Experiments at the Raft River Geothermal Test Site Author: Cole, L.T. Year: 1980 A fluidized-bed dryer was built and operated at the Raft River Geothermal Test Site in south central Idaho to test the feasibility of using low-temperature (145/sup 0/C or lower) geothermal fluids as an energy source for drying operations. The dryer performed successfully on two potato industry waste products that had a solid content of 5 to 13%. The dried product was removed as a sand-like granular material or as fines with a flour-like texture. Test results, observations, and design recommendations are presented. Also presented is an economic evaluation for commercial-scale drying plants using either geothermal low-temperature water or oil as a heat source Title: Fluidized-Bed Potato Waste Drying Experiments at the Raft River Geothermal Test Site Author: Cole, L.T. Year: 1980 A fluidized-bed dryer was built and operated at the Raft River Geothermal Test Site in south central Idaho to test the feasibility of using low-temperature (145/sup 0/C or lower) geothermal fluids as an energy source for drying operations. The dryer performed successfully on two potato industry waste products that had a solid content of 5 to 13%. The dried product was removed as a sand-like granular material or as fines with a flour-like texture. Test results, observations, and design recommendations are presented. Also presented is an economic evaluation for commercial-scale drying plants using either geothermal low-temperature water or oil as a heat source Close

• 4. [Image] Transient well testing in two-phase geothermal reservoirs

  	A study of well test analysis techniques in two-phase geothermal reservoirs has been conducted using a three-dimensional, two-phase, wellbore and reservoir simulation model. Well tests from Cerro Prieto ...
  	Citation × Citation Citation Abstract Copy Title: Transient well testing in two-phase geothermal reservoirs Author: Aydelotte, S.R. Year: 1980 A study of well test analysis techniques in two-phase geothermal reservoirs has been conducted using a three-dimensional, two-phase, wellbore and reservoir simulation model. Well tests from Cerro Prieto and the Hawaiian Geothermal project have been history matched. Using these well tests as a base, the influence of reservoir permeability, porosity, thickness, and heat capacity, along with flow rate and fracturing were studied. Single and two-phase transient well test equations were used to analyze these tests with poor results due to rapidly changing fluid properties and inability to calculate the flowing steam saturation in the reservoir. The injection of cold water into the reservoir does give good data from which formation properties can be calculated. Title: Transient well testing in two-phase geothermal reservoirs Author: Aydelotte, S.R. Year: 1980 A study of well test analysis techniques in two-phase geothermal reservoirs has been conducted using a three-dimensional, two-phase, wellbore and reservoir simulation model. Well tests from Cerro Prieto and the Hawaiian Geothermal project have been history matched. Using these well tests as a base, the influence of reservoir permeability, porosity, thickness, and heat capacity, along with flow rate and fracturing were studied. Single and two-phase transient well test equations were used to analyze these tests with poor results due to rapidly changing fluid properties and inability to calculate the flowing steam saturation in the reservoir. The injection of cold water into the reservoir does give good data from which formation properties can be calculated. Close