Search

Search Results

• 1. [Image] Evaluation and Design of Downhole Heat Exchangers for Direct Application; Annual Report, May 1, 1976 - July 1, 1977

  	Progress in an experimental and analytical research program to evaluate and improve the design of downhole heat exchangers (DHEs) for direct applications of geothermal energy is reported. Significant progress ...
  	Citation × Citation Citation Abstract Copy Title: Evaluation and Design of Downhole Heat Exchangers for Direct Application; Annual Report, May 1, 1976 - July 1, 1977 Author: Culver, G.G. Year: 1977 Progress in an experimental and analytical research program to evaluate and improve the design of downhole heat exchangers (DHEs) for direct applications of geothermal energy is reported. Significant progress has been achieved in characterizing flows in wells and without perforated casings and DHEs installed, determination of energy extraction rates for conventional DHEs in both cased and uncased wells, and utilization of information obtained to develop and substantiate models of heat transfer within the well. Flow characterization was obtained by experimentally measuring temperature and velocity profiles. In uncased wells, there was a relatively large vertical temperature gradient (approximately 0.5{sup 0}C/m) and insignificant measured vertical flow, while for the same wells when cased the temperature gradient was essentially zero (approximately 0.03{sup 0}C/m) and a large vertically upward flow was measured (9 to 14 cm/s as measured with a hot-film anemometer). These show that a significant connection cell is established after installation of the casing. The energy extraction rates for a conventional DHE both before and after casing of a 60 m deep well was experimentally measured. In the uncased well up to 300 kW was obtained while the cased well produced over 500 kW. Analytical heat transfer models were developed for the cased well both with and without DHEs. For the cased well without a DHE, the model predicts flow rates that agree with the measured value within about 30 percent. Further, the energy extraction rates predicted by the models agree even better with the measured values. These models allow the energy extraction rates of design parameter variations to be evaluated. At this stage, only trends can be shown but with additional substantiation they should produce optimum energy extraction designs Title: Evaluation and Design of Downhole Heat Exchangers for Direct Application; Annual Report, May 1, 1976 - July 1, 1977 Author: Culver, G.G. Year: 1977 Progress in an experimental and analytical research program to evaluate and improve the design of downhole heat exchangers (DHEs) for direct applications of geothermal energy is reported. Significant progress has been achieved in characterizing flows in wells and without perforated casings and DHEs installed, determination of energy extraction rates for conventional DHEs in both cased and uncased wells, and utilization of information obtained to develop and substantiate models of heat transfer within the well. Flow characterization was obtained by experimentally measuring temperature and velocity profiles. In uncased wells, there was a relatively large vertical temperature gradient (approximately 0.5{sup 0}C/m) and insignificant measured vertical flow, while for the same wells when cased the temperature gradient was essentially zero (approximately 0.03{sup 0}C/m) and a large vertically upward flow was measured (9 to 14 cm/s as measured with a hot-film anemometer). These show that a significant connection cell is established after installation of the casing. The energy extraction rates for a conventional DHE both before and after casing of a 60 m deep well was experimentally measured. In the uncased well up to 300 kW was obtained while the cased well produced over 500 kW. Analytical heat transfer models were developed for the cased well both with and without DHEs. For the cased well without a DHE, the model predicts flow rates that agree with the measured value within about 30 percent. Further, the energy extraction rates predicted by the models agree even better with the measured values. These models allow the energy extraction rates of design parameter variations to be evaluated. At this stage, only trends can be shown but with additional substantiation they should produce optimum energy extraction designs Close

• 2. [Image] Transient well testing in two-phase geothermal reservoirs

  	A study of well test analysis techniques in two-phase geothermal reservoirs has been conducted using a three-dimensional, two-phase, wellbore and reservoir simulation model. Well tests from Cerro Prieto ...
  	Citation × Citation Citation Abstract Copy Title: Transient well testing in two-phase geothermal reservoirs Author: Aydelotte, S.R. Year: 1980 A study of well test analysis techniques in two-phase geothermal reservoirs has been conducted using a three-dimensional, two-phase, wellbore and reservoir simulation model. Well tests from Cerro Prieto and the Hawaiian Geothermal project have been history matched. Using these well tests as a base, the influence of reservoir permeability, porosity, thickness, and heat capacity, along with flow rate and fracturing were studied. Single and two-phase transient well test equations were used to analyze these tests with poor results due to rapidly changing fluid properties and inability to calculate the flowing steam saturation in the reservoir. The injection of cold water into the reservoir does give good data from which formation properties can be calculated. Title: Transient well testing in two-phase geothermal reservoirs Author: Aydelotte, S.R. Year: 1980 A study of well test analysis techniques in two-phase geothermal reservoirs has been conducted using a three-dimensional, two-phase, wellbore and reservoir simulation model. Well tests from Cerro Prieto and the Hawaiian Geothermal project have been history matched. Using these well tests as a base, the influence of reservoir permeability, porosity, thickness, and heat capacity, along with flow rate and fracturing were studied. Single and two-phase transient well test equations were used to analyze these tests with poor results due to rapidly changing fluid properties and inability to calculate the flowing steam saturation in the reservoir. The injection of cold water into the reservoir does give good data from which formation properties can be calculated. Close