Search

Search Results

• 1. [Image] Geothermal exploration assessment and interpretation, Upper Klamath Lake Area, Klamath Basin, Oregon

  	Data from public and private sources on the Klamath Basin geothermal resource are reviewed, synthesized, and reinterpreted. In this, the second and final phase of the work, geological, remote sensing, ...
  	Citation × Citation Citation Abstract Copy Title: Geothermal exploration assessment and interpretation, Upper Klamath Lake Area, Klamath Basin, Oregon Author: Stark, M. Year: 1980 Data from public and private sources on the Klamath Basin geothermal resource are reviewed, synthesized, and reinterpreted. In this, the second and final phase of the work, geological, remote sensing, geochemical, temperature gradient, gravity, aeromagnetic, and electrical resistivity data sets are examined. These data were derived from surveys concentrated on the east and west shores of Upper Klamath Lake. The geological, remote sensing, and potential field data suggest a few northeast-trending discontinuities, which cross the regional north-westerly strike. The near-surface distribution of warm water appears to be related to the intersections of these lineaments and northwest-trending faults. The groundwater geochemical data are reviewed and the various reservoir temperature estimates compared. Particular attention is given to specific electrical conductivities of waters as an interpretational aid to the subsurface resistivity results. A clear trend emerges in the Klamath Falls/Olene Gap area; hotter waters are associated with higher specific conductivities. In the Nuss Lake/Stukel Mountain area the opposite trend prevails, although the relationship is somewhat equivocal; LBL-10140 Title: Geothermal exploration assessment and interpretation, Upper Klamath Lake Area, Klamath Basin, Oregon Author: Stark, M. Year: 1980 Data from public and private sources on the Klamath Basin geothermal resource are reviewed, synthesized, and reinterpreted. In this, the second and final phase of the work, geological, remote sensing, geochemical, temperature gradient, gravity, aeromagnetic, and electrical resistivity data sets are examined. These data were derived from surveys concentrated on the east and west shores of Upper Klamath Lake. The geological, remote sensing, and potential field data suggest a few northeast-trending discontinuities, which cross the regional north-westerly strike. The near-surface distribution of warm water appears to be related to the intersections of these lineaments and northwest-trending faults. The groundwater geochemical data are reviewed and the various reservoir temperature estimates compared. Particular attention is given to specific electrical conductivities of waters as an interpretational aid to the subsurface resistivity results. A clear trend emerges in the Klamath Falls/Olene Gap area; hotter waters are associated with higher specific conductivities. In the Nuss Lake/Stukel Mountain area the opposite trend prevails, although the relationship is somewhat equivocal; LBL-10140 Close

• 2. [Image] Dipole-Dipole Resistivity Surveys, Roosevelt Hot Springs KGRA. Final Report, Volume 2

  	Dipole-dipole Resistivity surveys were conducted at Roosevelt Hot Springs KGRA. Three different dipole spacings were used; 99km of traverse line were surveyed with 100m dipoles, 50km with 300m dipoles, ...
  	Citation × Citation Citation Abstract Copy Title: Dipole-Dipole Resistivity Surveys, Roosevelt Hot Springs KGRA. Final Report, Volume 2 Author: Ward, S.H. Year: 1976 Dipole-dipole Resistivity surveys were conducted at Roosevelt Hot Springs KGRA. Three different dipole spacings were used; 99km of traverse line were surveyed with 100m dipoles, 50km with 300m dipoles, and 44km with 1km dipoles. The objectives of the Resistivity surveying were to detect and delineate regions of low Resistivity associated with fracturing, brines, high temperatures, and clay alteration. The Resistivity of rocks that are typical of hydrothermal environments is due to two main conduction mechanisms: (1) electrolytic conduction through pores and fractures; and (2) surface conduction due to a thin zone of cations attracted to those mineral surfaces with net negative charges (especially clay minerals). For saturated rocks, the Resistivity due to electrolytic conduction is a function of the effective porosity of the fractured rock, of the temperature, and of the salinity of the fluid filling the pores and fractures. The Resistivity decreases as the effective porosity, water saturation, salinity, and temperature increase. The presence of clay minerals and pyrite will also decrease the Resistivity Title: Dipole-Dipole Resistivity Surveys, Roosevelt Hot Springs KGRA. Final Report, Volume 2 Author: Ward, S.H. Year: 1976 Dipole-dipole Resistivity surveys were conducted at Roosevelt Hot Springs KGRA. Three different dipole spacings were used; 99km of traverse line were surveyed with 100m dipoles, 50km with 300m dipoles, and 44km with 1km dipoles. The objectives of the Resistivity surveying were to detect and delineate regions of low Resistivity associated with fracturing, brines, high temperatures, and clay alteration. The Resistivity of rocks that are typical of hydrothermal environments is due to two main conduction mechanisms: (1) electrolytic conduction through pores and fractures; and (2) surface conduction due to a thin zone of cations attracted to those mineral surfaces with net negative charges (especially clay minerals). For saturated rocks, the Resistivity due to electrolytic conduction is a function of the effective porosity of the fractured rock, of the temperature, and of the salinity of the fluid filling the pores and fractures. The Resistivity decreases as the effective porosity, water saturation, salinity, and temperature increase. The presence of clay minerals and pyrite will also decrease the Resistivity Close

• 3. [Image] Geological and Geophysical Study of the Origin of the Warm Springs in Bath County, Virginia. Final Report, June 1, 1975--April 30, 1976

  	The results of heat flow determinations and a reconnaissance dipole electrical resistivity survey in Bath County are described. A geologic map was compiled based on published maps and supported by reconnaissance ...
  	Citation × Citation Citation Abstract Copy Title: Geological and Geophysical Study of the Origin of the Warm Springs in Bath County, Virginia. Final Report, June 1, 1975--April 30, 1976 Author: Costain, J.K. Year: 1976 The results of heat flow determinations and a reconnaissance dipole electrical resistivity survey in Bath County are described. A geologic map was compiled based on published maps and supported by reconnaissance geologic mapping in areas where published maps were not available. A regional bipole--dipole electrical resistivity survey was made in order to detect the presence of resistivity lows that might be associated with a geothermal system at depth. A single hole was drilled to a depth of approximately 300 m (approx. 1000 feet) to obtain a heat flow value that is representative of the area. The data were used to attempt to arrive at a model that unambiguously explains the origin of the thermal springs Title: Geological and Geophysical Study of the Origin of the Warm Springs in Bath County, Virginia. Final Report, June 1, 1975--April 30, 1976 Author: Costain, J.K. Year: 1976 The results of heat flow determinations and a reconnaissance dipole electrical resistivity survey in Bath County are described. A geologic map was compiled based on published maps and supported by reconnaissance geologic mapping in areas where published maps were not available. A regional bipole--dipole electrical resistivity survey was made in order to detect the presence of resistivity lows that might be associated with a geothermal system at depth. A single hole was drilled to a depth of approximately 300 m (approx. 1000 feet) to obtain a heat flow value that is representative of the area. The data were used to attempt to arrive at a model that unambiguously explains the origin of the thermal springs Close

• 4. [Image] Downhole Electrical Detection of Hydraulic Fractures in GT-2 and EE-1

  	Electrical geophysical methods including mise a la masse and self-potential (SP) for determination of hydraulic fracture characteristics were used at the hot dry rock geothermal project. Electrical and ...
  	Citation × Citation Citation Abstract Copy Title: Downhole Electrical Detection of Hydraulic Fractures in GT-2 and EE-1 Author: Kintzinger, P.R. Year: 1977 Electrical geophysical methods including mise a la masse and self-potential (SP) for determination of hydraulic fracture characteristics were used at the hot dry rock geothermal project. Electrical and induction logs indicated that the resistivity contrast between the granite and 200/sup 0/C water at the 2926-m (9600-ft) depth is a factor of 1000 or more. Thus the water in a hydraulic fracture, formed to connect two adjacent deep holes, is a good conductor compared to the confining granite. Mise a la masse-type measurements were made to help determine the characteristics for hydraulic fractures formed in each of the two geothermal holes GT-2 and EE-1. Once a hydraulic fracture has been formed, mise a la masse effects are obtained both with the fracture pressurized above hydrostatic and when depressurized to hydrostatic. This indicates that once the fracture has been created, enough natural propping exists that a conductive zone persists even when the fracture is deflated. A fracture was formed in a 18-m (60-ft) zone immediately below 1957 m (6420 ft) in EE-1. Later a set of SP logs was run in this zone with no pressure, with pressure building, with pressure decreasing, and again with the fracture depressurized. Results show that during times of change of parameters in hydraulically fractured regions in the hole, natural SP logging helps to determine the position of the fracture. However, after a fracture has come to equilibrium with fluid parameters such as temperature, pressure, salinity, and pH, an effect of the fracture may not be evident. Self-potential logs provide an excellent method for locating the bottom of steel casing that has been set in the hole Title: Downhole Electrical Detection of Hydraulic Fractures in GT-2 and EE-1 Author: Kintzinger, P.R. Year: 1977 Electrical geophysical methods including mise a la masse and self-potential (SP) for determination of hydraulic fracture characteristics were used at the hot dry rock geothermal project. Electrical and induction logs indicated that the resistivity contrast between the granite and 200/sup 0/C water at the 2926-m (9600-ft) depth is a factor of 1000 or more. Thus the water in a hydraulic fracture, formed to connect two adjacent deep holes, is a good conductor compared to the confining granite. Mise a la masse-type measurements were made to help determine the characteristics for hydraulic fractures formed in each of the two geothermal holes GT-2 and EE-1. Once a hydraulic fracture has been formed, mise a la masse effects are obtained both with the fracture pressurized above hydrostatic and when depressurized to hydrostatic. This indicates that once the fracture has been created, enough natural propping exists that a conductive zone persists even when the fracture is deflated. A fracture was formed in a 18-m (60-ft) zone immediately below 1957 m (6420 ft) in EE-1. Later a set of SP logs was run in this zone with no pressure, with pressure building, with pressure decreasing, and again with the fracture depressurized. Results show that during times of change of parameters in hydraulically fractured regions in the hole, natural SP logging helps to determine the position of the fracture. However, after a fracture has come to equilibrium with fluid parameters such as temperature, pressure, salinity, and pH, an effect of the fracture may not be evident. Self-potential logs provide an excellent method for locating the bottom of steel casing that has been set in the hole Close

• 5. [Image] Geothermal Resources, Vicksburg Formation, Texas Gulf Coast

  	The potential for discovering geopressured geothermal reservoirs in the Vicksburg Formation is limited to Hidalgo County along the Lower Texas Gulf Coast. In Hidalgo County, an area of approximately 385 ...
  	Citation × Citation Citation Abstract Copy Title: Geothermal Resources, Vicksburg Formation, Texas Gulf Coast Author: Loucks, R.G. Year: 1978 The potential for discovering geopressured geothermal reservoirs in the Vicksburg Formation is limited to Hidalgo County along the Lower Texas Gulf Coast. In Hidalgo County, an area of approximately 385 square miles (designated the Vicksburg Fairway) contains up to 1,300 feet of geopressured sandstones with fluid temperatures greater than 300/sup 0/F. In-place effective permeability, however, averages less than 1 millidarcy in the Vicksburg sandstones because of fine grain size and extensive late carbonate cementation. Also, areal extent of individual reservoirs is limited in a dip direction by growth faults and in a strike direction by the lenticular morphology of the sandstone bodies. In conclusion, under the present specifications set for a geothermal fairway, the Vicksburg has minimal potential because of low reservoir deliverability, which is constrained by low permeability and somewhat limited reservoir continuity. If future tests indicate that lower permeabilities are acceptable, the Vicksburg Fairway should be reconsidered because of the presence of extremely thick sandstone bodies Title: Geothermal Resources, Vicksburg Formation, Texas Gulf Coast Author: Loucks, R.G. Year: 1978 The potential for discovering geopressured geothermal reservoirs in the Vicksburg Formation is limited to Hidalgo County along the Lower Texas Gulf Coast. In Hidalgo County, an area of approximately 385 square miles (designated the Vicksburg Fairway) contains up to 1,300 feet of geopressured sandstones with fluid temperatures greater than 300/sup 0/F. In-place effective permeability, however, averages less than 1 millidarcy in the Vicksburg sandstones because of fine grain size and extensive late carbonate cementation. Also, areal extent of individual reservoirs is limited in a dip direction by growth faults and in a strike direction by the lenticular morphology of the sandstone bodies. In conclusion, under the present specifications set for a geothermal fairway, the Vicksburg has minimal potential because of low reservoir deliverability, which is constrained by low permeability and somewhat limited reservoir continuity. If future tests indicate that lower permeabilities are acceptable, the Vicksburg Fairway should be reconsidered because of the presence of extremely thick sandstone bodies Close

• 6. [Image] Exploration Methods for Hot Dry Rock. Report of the Panel Held June 22, 1976

  	The geological and geophysical characteristics of hot dry rock (HDR) necessary for an effective exploration program were discussed. The type of HDR project discussed, that being developed by the Los Alamos ...
  	Citation × Citation Citation Abstract Copy Title: Exploration Methods for Hot Dry Rock. Report of the Panel Held June 22, 1976 Author: West, F.G. (comp.) Year: 1977 The geological and geophysical characteristics of hot dry rock (HDR) necessary for an effective exploration program were discussed. The type of HDR project discussed, that being developed by the Los Alamos Scientific Laboratory (LASL), would utilize hydraulic fracturing to develop a large surface area in rock of low permeability, 10/sup -6/ darcys, and at temperatures greater than 200/sup 0/C. A better definition of the thermal regime in the crust and mantle at reconnaissance (hundreds to tens of kilometers) and exploration (tens of kilometers to 1 km) scales is needed. Geophysical methods capable of deep investigation would be used with the near-surface geologic information to extrapolate conditions at the depth of interest. Detection of HDR per se may be difficult because the contrast in physical properties of HDR and other rock is not always unambiguous, but boundaries between rock environments can be delineated. When patterns and coincidence of various types of geophysical anomalies and geologic maps are used, the probability of the detection of HDR is greatly increased, especially when a consistent picture is described. Various geophysical methods are required to detect these anomalies: (a) electromagnetic techniques can map deep electrically conductive structures, which to some extent can be used to infer isotherms. (b) Bouguer gravity maps corrected for regional topography are found to correlate with large silicic intrusive bodies, which are often associated with high heat flow. (c) isotherms and open crack systems at depth can be inferred from seismic wave attenuations, dispersions, and delay times. (d) heat flow measurements are useful as a primary tool and as a check on the results of other methods. Abstracts for individual presentations by the twelve panel members are included. 111 references Title: Exploration Methods for Hot Dry Rock. Report of the Panel Held June 22, 1976 Author: West, F.G. (comp.) Year: 1977 The geological and geophysical characteristics of hot dry rock (HDR) necessary for an effective exploration program were discussed. The type of HDR project discussed, that being developed by the Los Alamos Scientific Laboratory (LASL), would utilize hydraulic fracturing to develop a large surface area in rock of low permeability, 10/sup -6/ darcys, and at temperatures greater than 200/sup 0/C. A better definition of the thermal regime in the crust and mantle at reconnaissance (hundreds to tens of kilometers) and exploration (tens of kilometers to 1 km) scales is needed. Geophysical methods capable of deep investigation would be used with the near-surface geologic information to extrapolate conditions at the depth of interest. Detection of HDR per se may be difficult because the contrast in physical properties of HDR and other rock is not always unambiguous, but boundaries between rock environments can be delineated. When patterns and coincidence of various types of geophysical anomalies and geologic maps are used, the probability of the detection of HDR is greatly increased, especially when a consistent picture is described. Various geophysical methods are required to detect these anomalies: (a) electromagnetic techniques can map deep electrically conductive structures, which to some extent can be used to infer isotherms. (b) Bouguer gravity maps corrected for regional topography are found to correlate with large silicic intrusive bodies, which are often associated with high heat flow. (c) isotherms and open crack systems at depth can be inferred from seismic wave attenuations, dispersions, and delay times. (d) heat flow measurements are useful as a primary tool and as a check on the results of other methods. Abstracts for individual presentations by the twelve panel members are included. 111 references Close