Search

Search Results

• 1. [Image] Geological and Geophysical Analysis of Coso Geothermal Exploration Hole No. 1 (CGEH-1), Coso Hot Springs KGRA, California

  	The Coso Geothermal Exploration Hole number one (CGEH-1) was drilled in the Coso Hot Springs KGRA, California from September 2 to December 2, 1977. Chip samples were collected at ten foot intervals and ...
  	Citation × Citation Citation Abstract Copy Title: Geological and Geophysical Analysis of Coso Geothermal Exploration Hole No. 1 (CGEH-1), Coso Hot Springs KGRA, California Author: Galbraith, R.M. Year: 1978 The Coso Geothermal Exploration Hole number one (CGEH-1) was drilled in the Coso Hot Springs KGRA, California from September 2 to December 2, 1977. Chip samples were collected at ten foot intervals and extensive geophysical logging surveys were conducted to document the geologic character of the geothermal system as penetrated by CGEH-1. The major rock units encountered include a mafic metamorphic sequence and a leucogranite which intruded the metamorphic rocks. Only weak hydrothermal alteration was noted in these rocks. Drillhole surveys and drilling rate data indicate that the geothermal system is structurally controlled and that the drillhole itself was strongly influenced by structural zones. Water chemistry indicates that this geothermal resource is a hot-water rather than a vapor-dominated system. Several geophysical logs were employed to characterize the drillhole geology. The natural gamma and neutron porosity logs indicate gross rock type and the acoustic logs indicate fractured rock and potentially permeable zones. A series of temperature logs run as a function of time during and after the completion of Drilling were most Useful in delineating the zones of maximum heat flux. Convective heat flow and temperatures greater than 350/sup 0/F appear to occur only along an open fracture system encountered between depths of 1850 and 2775 feet. Temperature logs indicate a negative thermal gradient below 3000 feet Title: Geological and Geophysical Analysis of Coso Geothermal Exploration Hole No. 1 (CGEH-1), Coso Hot Springs KGRA, California Author: Galbraith, R.M. Year: 1978 The Coso Geothermal Exploration Hole number one (CGEH-1) was drilled in the Coso Hot Springs KGRA, California from September 2 to December 2, 1977. Chip samples were collected at ten foot intervals and extensive geophysical logging surveys were conducted to document the geologic character of the geothermal system as penetrated by CGEH-1. The major rock units encountered include a mafic metamorphic sequence and a leucogranite which intruded the metamorphic rocks. Only weak hydrothermal alteration was noted in these rocks. Drillhole surveys and drilling rate data indicate that the geothermal system is structurally controlled and that the drillhole itself was strongly influenced by structural zones. Water chemistry indicates that this geothermal resource is a hot-water rather than a vapor-dominated system. Several geophysical logs were employed to characterize the drillhole geology. The natural gamma and neutron porosity logs indicate gross rock type and the acoustic logs indicate fractured rock and potentially permeable zones. A series of temperature logs run as a function of time during and after the completion of Drilling were most Useful in delineating the zones of maximum heat flux. Convective heat flow and temperatures greater than 350/sup 0/F appear to occur only along an open fracture system encountered between depths of 1850 and 2775 feet. Temperature logs indicate a negative thermal gradient below 3000 feet Close

• 2. [Image] Geological and Geophysical Analysis of Coso Geothermal Exploration Hole No. 1 (CGEH-1), Coso Hot Springs KGRA, California

  	The Coso Geothermal Exploration Hole number one (CGEH-1) was drilled in the Coso Hot Springs KGRA, California, from September 2 to December 2, 1977. Chip samples were collected at ten foot intervals and ...
  	Citation × Citation Citation Abstract Copy Title: Geological and Geophysical Analysis of Coso Geothermal Exploration Hole No. 1 (CGEH-1), Coso Hot Springs KGRA, California Author: Galbraith, R.M. Year: 1978 The Coso Geothermal Exploration Hole number one (CGEH-1) was drilled in the Coso Hot Springs KGRA, California, from September 2 to December 2, 1977. Chip samples were collected at ten foot intervals and extensive geophysical logging surveys were conducted to document the geologic character of the geothermal system as penetrated by CGEH-1. The major rock units encountered include a mafic metamorphic sequence and a leucogranite which intruded the metamorphic rocks. Only weak hydrothermal alteration was noted in these rocks. Drillhole surveys and drilling rate data indicate that the geothermal system is structurally controlled and that the drillhole itself was strongly influenced by structural zones. Water chemistry indicates that this geothermal resource is a hot-water rather than a vapor-dominated system. Several geophysical logs were employed to characterize the drillhole geology. The natural gamma and neutron porosity logs indicate gross rock type and the acoustics logs indicate fractured rock and potentially permeable zones. A series of temperature logs run as a function of time during and after the completion of drilling were most useful in delineating the zones of maximum heat flux. Convective heat flow and temperatures greater than 350/sup 0/F appear to occur only along an open fracture system encountered between depths of 1850 and 2775 feet. Temperature logs indicate a negative thermal gradient below 3000 feet Title: Geological and Geophysical Analysis of Coso Geothermal Exploration Hole No. 1 (CGEH-1), Coso Hot Springs KGRA, California Author: Galbraith, R.M. Year: 1978 The Coso Geothermal Exploration Hole number one (CGEH-1) was drilled in the Coso Hot Springs KGRA, California, from September 2 to December 2, 1977. Chip samples were collected at ten foot intervals and extensive geophysical logging surveys were conducted to document the geologic character of the geothermal system as penetrated by CGEH-1. The major rock units encountered include a mafic metamorphic sequence and a leucogranite which intruded the metamorphic rocks. Only weak hydrothermal alteration was noted in these rocks. Drillhole surveys and drilling rate data indicate that the geothermal system is structurally controlled and that the drillhole itself was strongly influenced by structural zones. Water chemistry indicates that this geothermal resource is a hot-water rather than a vapor-dominated system. Several geophysical logs were employed to characterize the drillhole geology. The natural gamma and neutron porosity logs indicate gross rock type and the acoustics logs indicate fractured rock and potentially permeable zones. A series of temperature logs run as a function of time during and after the completion of drilling were most useful in delineating the zones of maximum heat flux. Convective heat flow and temperatures greater than 350/sup 0/F appear to occur only along an open fracture system encountered between depths of 1850 and 2775 feet. Temperature logs indicate a negative thermal gradient below 3000 feet Close

• 3. [Image] Long-Term Supply Curves for Geothermal Energy - The Impacts of Technology

  	Near-term and long-term supply curves are presented for electric applications of geothermal energy. The GEOCOST model was used to determine the present and future energy production costs for the high-temperature ...
  	Citation × Citation Citation Abstract Copy Title: Long-Term Supply Curves for Geothermal Energy - The Impacts of Technology Author: Fassbender, L.L. Year: 1980 Near-term and long-term supply curves are presented for electric applications of geothermal energy. The GEOCOST model was used to determine the present and future energy production costs for the high-temperature and intermediate-temperature hydrothermal resources identified by the USGS The long-term supply curves illustrate the potential shifts in the near-term supply curve which would result from certain technology improvements currently being pursued. Programs with the most significant potential impacts are those which result in large reductions in drilling cost, those which lead to development of commercial high capacity downhole pumps, and those which lead to large increases in the plant capacity factor. Curves were drawn to show the impacts of individual technology improvements and also to show the cumulative impacts of combinations of technological advances expected to be achieved by 1982 and 1985. Successful completion of all the programs evaluated would result in a cumulative cost reduction of $90 billion (not discounted) in electrical generating costs from the identified hydrothermal resources Title: Long-Term Supply Curves for Geothermal Energy - The Impacts of Technology Author: Fassbender, L.L. Year: 1980 Near-term and long-term supply curves are presented for electric applications of geothermal energy. The GEOCOST model was used to determine the present and future energy production costs for the high-temperature and intermediate-temperature hydrothermal resources identified by the USGS The long-term supply curves illustrate the potential shifts in the near-term supply curve which would result from certain technology improvements currently being pursued. Programs with the most significant potential impacts are those which result in large reductions in drilling cost, those which lead to development of commercial high capacity downhole pumps, and those which lead to large increases in the plant capacity factor. Curves were drawn to show the impacts of individual technology improvements and also to show the cumulative impacts of combinations of technological advances expected to be achieved by 1982 and 1985. Successful completion of all the programs evaluated would result in a cumulative cost reduction of $90 billion (not discounted) in electrical generating costs from the identified hydrothermal resources Close

• 4. [Image] Hot Dry Rock Geothermal Energy Development Program, Annual Report, Fiscal Year 1980

  	Investigation and flow testing of the enlarged Phase I heat-extraction system at Fenton Hill continued throughout FY80. Temperature drawdown observed at that time indicated an effective fracture of approximately ...
  	Citation × Citation Citation Abstract Copy Title: Hot Dry Rock Geothermal Energy Development Program, Annual Report, Fiscal Year 1980 Author: Cremer, G.M. (comp.) Year: 1981 Investigation and flow testing of the enlarged Phase I heat-extraction system at Fenton Hill continued throughout FY80. Temperature drawdown observed at that time indicated an effective fracture of approximately 40,000 to 60,000 m/sup 2/. In May 1980, hot dry rock (HDR) technology was used to produce electricity in an interface demonstration experiment at Fenton Hill. A 60-kVA binary-cycle electrical generator was installed in the Phase I surface system and heat from about 3 kg/s of geothermal fluid at 132/sup 0/C was used to boil Freon R-114, whose vapor drove a turboalternator. A Phase II system was designed and is now being constructed at Fenton Hill that should approach commercial requirements. Borehole EE-2, the injection well, was completed on May 12, 1980. It was drilled to a vertical depth of about 4500 m, where the rock temperature is approximately 320/sup 0/C. The production well, EE-3 had been drilled to a depth of 3044 m and drilling was continuing. Environmental monitoring of Fenton Hill site continued. Development of equipment, instruments, and materials for technical support at Fenton Hill continued during FY80. Several kinds of models were also developed to understand the behavior of the Phase I system and to develop a predictive capability for future systems. Data from extensive resource investigations were collected, analyzed, and assembled into a geothermal gradient map of the US, and studies were completed on five specific areas as possible locations for HDR Experimental Site 2 Title: Hot Dry Rock Geothermal Energy Development Program, Annual Report, Fiscal Year 1980 Author: Cremer, G.M. (comp.) Year: 1981 Investigation and flow testing of the enlarged Phase I heat-extraction system at Fenton Hill continued throughout FY80. Temperature drawdown observed at that time indicated an effective fracture of approximately 40,000 to 60,000 m/sup 2/. In May 1980, hot dry rock (HDR) technology was used to produce electricity in an interface demonstration experiment at Fenton Hill. A 60-kVA binary-cycle electrical generator was installed in the Phase I surface system and heat from about 3 kg/s of geothermal fluid at 132/sup 0/C was used to boil Freon R-114, whose vapor drove a turboalternator. A Phase II system was designed and is now being constructed at Fenton Hill that should approach commercial requirements. Borehole EE-2, the injection well, was completed on May 12, 1980. It was drilled to a vertical depth of about 4500 m, where the rock temperature is approximately 320/sup 0/C. The production well, EE-3 had been drilled to a depth of 3044 m and drilling was continuing. Environmental monitoring of Fenton Hill site continued. Development of equipment, instruments, and materials for technical support at Fenton Hill continued during FY80. Several kinds of models were also developed to understand the behavior of the Phase I system and to develop a predictive capability for future systems. Data from extensive resource investigations were collected, analyzed, and assembled into a geothermal gradient map of the US, and studies were completed on five specific areas as possible locations for HDR Experimental Site 2 Close

• 5. [Image] Completion and testing report: INEL Geothermal Exploratory Well One (INEL-1)

  	INEL Geothermal Exploratory Well One (INEL-1) was drilled in search of a geothermal resource beneath the Snake River Plain for use at the Chemical Processing Plant (CPP) on the Idaho National Engineering ...
  	Citation × Citation Citation Abstract Copy Title: Completion and testing report: INEL Geothermal Exploratory Well One (INEL-1) Author: Prestwich, S.M. Year: 1980 INEL Geothermal Exploratory Well One (INEL-1) was drilled in search of a geothermal resource beneath the Snake River Plain for use at the Chemical Processing Plant (CPP) on the Idaho National Engineering Laboratory Site. The drilling site was selected as the most promising location within reasonable distance of the CPP. The resource was thought to be located at a depth near 7500 ft (2300 m). Neither significant production nor high temperatures were noted at that depth, and the well was then drilled to 10,333 ft (3150 m) with similar findings. Rock cores, geophysical logs, and hydrologic tests of the well to date indicate that no useful geothermal resource exists at this location. Information is presented on the drilling, completion, and testing of INEL-1; IDO-10096 Title: Completion and testing report: INEL Geothermal Exploratory Well One (INEL-1) Author: Prestwich, S.M. Year: 1980 INEL Geothermal Exploratory Well One (INEL-1) was drilled in search of a geothermal resource beneath the Snake River Plain for use at the Chemical Processing Plant (CPP) on the Idaho National Engineering Laboratory Site. The drilling site was selected as the most promising location within reasonable distance of the CPP. The resource was thought to be located at a depth near 7500 ft (2300 m). Neither significant production nor high temperatures were noted at that depth, and the well was then drilled to 10,333 ft (3150 m) with similar findings. Rock cores, geophysical logs, and hydrologic tests of the well to date indicate that no useful geothermal resource exists at this location. Information is presented on the drilling, completion, and testing of INEL-1; IDO-10096 Close

• 6. [Image] Planning, Drilling, Logging, and Testing of Energy Extraction Hole EE-1, Phases I and II

  	Energy Extraction Hole No. 1 (EE-1) is the second deep hole drilled into the Precambrian-age granitic rocks of the Jemez Mountains of north-central New Mexico. EE-1 was drilled to intersect a hydraulic ...
  	Citation × Citation Citation Abstract Copy Title: Planning, Drilling, Logging, and Testing of Energy Extraction Hole EE-1, Phases I and II Author: Pettitt, R.A. Year: 1977 Energy Extraction Hole No. 1 (EE-1) is the second deep hole drilled into the Precambrian-age granitic rocks of the Jemez Mountains of north-central New Mexico. EE-1 was drilled to intersect a hydraulic fracture extending outward from near the bottom of previously drilled hole GT-2, thus completing the underground circulation loop required for the hot dry rock geothermal energy extraction experiment. Directional drilling techniques were used to intersect the fracture zone. In addition, high-temperature instrumentation and equipment development, hydraulic fracturing experiments, pressure-flow testing of the fracture systems, and fracture mapping and borehole-ranging technique activities were conducted. The drilling, logging, and testing operations in EE-1 are described Title: Planning, Drilling, Logging, and Testing of Energy Extraction Hole EE-1, Phases I and II Author: Pettitt, R.A. Year: 1977 Energy Extraction Hole No. 1 (EE-1) is the second deep hole drilled into the Precambrian-age granitic rocks of the Jemez Mountains of north-central New Mexico. EE-1 was drilled to intersect a hydraulic fracture extending outward from near the bottom of previously drilled hole GT-2, thus completing the underground circulation loop required for the hot dry rock geothermal energy extraction experiment. Directional drilling techniques were used to intersect the fracture zone. In addition, high-temperature instrumentation and equipment development, hydraulic fracturing experiments, pressure-flow testing of the fracture systems, and fracture mapping and borehole-ranging technique activities were conducted. The drilling, logging, and testing operations in EE-1 are described Close