Search

Search Results

• 1. [Image] C. D. Hopkins, et al. , No. 2. Geothermal Well-Of-Opportunity, Wayne County, Georgia. Operational Report

  	An oil and gas exploration well, located near Jesup in Wayne County, Georgia (lat. 31/sup 0/32' N, long. 81/sup 0/43' W), was deepened and used for geothermal temperature-gradient measurements. The well ...
  	Citation × Citation Citation Abstract Copy Title: C. D. Hopkins, et al. , No. 2. Geothermal Well-Of-Opportunity, Wayne County, Georgia. Operational Report Author: Lohse, A. Year: 1978 An oil and gas exploration well, located near Jesup in Wayne County, Georgia (lat. 31/sup 0/32' N, long. 81/sup 0/43' W), was deepened and used for geothermal temperature-gradient measurements. The well was drilled from 4,009 to 4,341 feet, then diamond cored to 4,371 feet, 28 feet of core being obtained for analysis. After logging by the U.S.G.S. District Groundwater Office in Atlanta, the well was terminated with 3/sup 1///sub 2/'' tubing to 4,386 feet. The bottom-hole temperature was determined to be 60/sup 0/C (140/sup 0/F) at 1,331 meters (4,365 feet). Over the interval 47 to 1,331 meters (154 to 4,365 feet) the least-squares temperature gradient was 29.3 +- 0.14 /sup 0/C/km (1.61 +- 0.25 /sup 0/F/100 ft) Title: C. D. Hopkins, et al. , No. 2. Geothermal Well-Of-Opportunity, Wayne County, Georgia. Operational Report Author: Lohse, A. Year: 1978 An oil and gas exploration well, located near Jesup in Wayne County, Georgia (lat. 31/sup 0/32' N, long. 81/sup 0/43' W), was deepened and used for geothermal temperature-gradient measurements. The well was drilled from 4,009 to 4,341 feet, then diamond cored to 4,371 feet, 28 feet of core being obtained for analysis. After logging by the U.S.G.S. District Groundwater Office in Atlanta, the well was terminated with 3/sup 1///sub 2/'' tubing to 4,386 feet. The bottom-hole temperature was determined to be 60/sup 0/C (140/sup 0/F) at 1,331 meters (4,365 feet). Over the interval 47 to 1,331 meters (154 to 4,365 feet) the least-squares temperature gradient was 29.3 +- 0.14 /sup 0/C/km (1.61 +- 0.25 /sup 0/F/100 ft) Close

• 2. [Image] Thermal Gradient and Heat Flow Drilling, Volume 5, Final Report

  	During the summer of 1975, the Department of Geology and Geophysics drilled nine drill thermal gradient/heat flow holes. Total footage drilled was 2125 feet. Seven holes were drilled with a Mayhew 1000 ...
  	Citation × Citation Citation Abstract Copy Title: Thermal Gradient and Heat Flow Drilling, Volume 5, Final Report Author: Whelan, J.A. Year: 1977 During the summer of 1975, the Department of Geology and Geophysics drilled nine drill thermal gradient/heat flow holes. Total footage drilled was 2125 feet. Seven holes were drilled with a Mayhew 1000 drill using various combinations of down the hole hammer drilling, rotary drilling, and NX diamond core drilling. Three of these were heat flow holes--one in the Mineral Range, one in the Tushar Range near Beaver, Utah, and one near Monroe, Utah. Two were alteration study holes in the Roosevelt KGRA and two were temperature gradient holes, in alluvium in the Roosevelt KGRA. The average depth of the holes drilled with the Mayhew 1000 drill was 247 feet. Holes ranged from 135 feet to 492 feet. Cost per foot averaged $18.53. Two holes were core drilled with a Joy 12, BX-size drill. One was to 75 feet, in perlite. This hole was abandoned. The other was to 323 feet in granite. These holes averaged $13.82 per foot. Permission to drill was obtained from BLM and drill sites were inspected with BLM personnel to avoid disturbing archeological sites. Sites were reseeded where disturbed. Holes were completed by setting capped one-inch black iron pipe, backfilling the hole with cuttings to 10 feet from surface and cementing to the surface Title: Thermal Gradient and Heat Flow Drilling, Volume 5, Final Report Author: Whelan, J.A. Year: 1977 During the summer of 1975, the Department of Geology and Geophysics drilled nine drill thermal gradient/heat flow holes. Total footage drilled was 2125 feet. Seven holes were drilled with a Mayhew 1000 drill using various combinations of down the hole hammer drilling, rotary drilling, and NX diamond core drilling. Three of these were heat flow holes--one in the Mineral Range, one in the Tushar Range near Beaver, Utah, and one near Monroe, Utah. Two were alteration study holes in the Roosevelt KGRA and two were temperature gradient holes, in alluvium in the Roosevelt KGRA. The average depth of the holes drilled with the Mayhew 1000 drill was 247 feet. Holes ranged from 135 feet to 492 feet. Cost per foot averaged $18.53. Two holes were core drilled with a Joy 12, BX-size drill. One was to 75 feet, in perlite. This hole was abandoned. The other was to 323 feet in granite. These holes averaged $13.82 per foot. Permission to drill was obtained from BLM and drill sites were inspected with BLM personnel to avoid disturbing archeological sites. Sites were reseeded where disturbed. Holes were completed by setting capped one-inch black iron pipe, backfilling the hole with cuttings to 10 feet from surface and cementing to the surface Close

• 3. [Image] Geological and Geophysical Study of the Origin of the Warm Springs in Bath County, Virginia. Final Report, June 1, 1975--April 30, 1976

  	The results of heat flow determinations and a reconnaissance dipole electrical resistivity survey in Bath County are described. A geologic map was compiled based on published maps and supported by reconnaissance ...
  	Citation × Citation Citation Abstract Copy Title: Geological and Geophysical Study of the Origin of the Warm Springs in Bath County, Virginia. Final Report, June 1, 1975--April 30, 1976 Author: Costain, J.K. Year: 1976 The results of heat flow determinations and a reconnaissance dipole electrical resistivity survey in Bath County are described. A geologic map was compiled based on published maps and supported by reconnaissance geologic mapping in areas where published maps were not available. A regional bipole--dipole electrical resistivity survey was made in order to detect the presence of resistivity lows that might be associated with a geothermal system at depth. A single hole was drilled to a depth of approximately 300 m (approx. 1000 feet) to obtain a heat flow value that is representative of the area. The data were used to attempt to arrive at a model that unambiguously explains the origin of the thermal springs Title: Geological and Geophysical Study of the Origin of the Warm Springs in Bath County, Virginia. Final Report, June 1, 1975--April 30, 1976 Author: Costain, J.K. Year: 1976 The results of heat flow determinations and a reconnaissance dipole electrical resistivity survey in Bath County are described. A geologic map was compiled based on published maps and supported by reconnaissance geologic mapping in areas where published maps were not available. A regional bipole--dipole electrical resistivity survey was made in order to detect the presence of resistivity lows that might be associated with a geothermal system at depth. A single hole was drilled to a depth of approximately 300 m (approx. 1000 feet) to obtain a heat flow value that is representative of the area. The data were used to attempt to arrive at a model that unambiguously explains the origin of the thermal springs Close

• 4. [Image] Non-Electric Applications of Geothermal Energy in Six Alaskan Towns. Final Report, October 1976--November 1977

  	The potential for direct (non-electric) utilization of local-gradient geothermal energy in six Alaskan towns is summarized. A major objective of this study was to stimulate development and Use of the geothermal ...
  	Citation × Citation Citation Abstract Copy Title: Non-Electric Applications of Geothermal Energy in Six Alaskan Towns. Final Report, October 1976--November 1977 Author: Farquhar, J. Year: 1977 The potential for direct (non-electric) utilization of local-gradient geothermal energy in six Alaskan towns is summarized. A major objective of this study was to stimulate development and Use of the geothermal resource provided by the earth's average thermal gradient, as opposed to the few anomalies that are typically chosen for geothermal development. Hence, six towns for study were selected as being representative of remote Alaskan conditions, rather than for their proximity to known geothermal resources. The moderate-temperature heat available almost everywhere at depths of two to four kilometers into the earth's mantle could satisfy a major portion of the nation's heating requirements--but the cost must be reduced. It is concluded that a geothermal demonstration in Nome would probably be successful and would promote this objective Title: Non-Electric Applications of Geothermal Energy in Six Alaskan Towns. Final Report, October 1976--November 1977 Author: Farquhar, J. Year: 1977 The potential for direct (non-electric) utilization of local-gradient geothermal energy in six Alaskan towns is summarized. A major objective of this study was to stimulate development and Use of the geothermal resource provided by the earth's average thermal gradient, as opposed to the few anomalies that are typically chosen for geothermal development. Hence, six towns for study were selected as being representative of remote Alaskan conditions, rather than for their proximity to known geothermal resources. The moderate-temperature heat available almost everywhere at depths of two to four kilometers into the earth's mantle could satisfy a major portion of the nation's heating requirements--but the cost must be reduced. It is concluded that a geothermal demonstration in Nome would probably be successful and would promote this objective Close

• 5. [Image] The Marysville, Montana Geothermal Project (Revised)

  	The object of the Marysville Geothermal Project is to investigate a region of abnormally high geothermal heat flow near Marysville, MT, about 20 miles northwest of Helena. The research should determine ...
  	Citation × Citation Citation Abstract Copy Title: The Marysville, Montana Geothermal Project (Revised) Author: McSpadden, W.R. Year: 1974 The object of the Marysville Geothermal Project is to investigate a region of abnormally high geothermal heat flow near Marysville, MT, about 20 miles northwest of Helena. The research should determine the nature and size of the resource, how the energy might be extracted, the potential monetary value of the energy, and how similar resources elsewhere might be located. The heat source was expected to be a granitic pluton or magmatic intrusion, 10,000 to 40,000 years old, with temperatures in the range of 300 to 500°C. Originally it was thought that the pluton was at relatively shallow depths, but at present its depth and exact location are unknown Title: The Marysville, Montana Geothermal Project (Revised) Author: McSpadden, W.R. Year: 1974 The object of the Marysville Geothermal Project is to investigate a region of abnormally high geothermal heat flow near Marysville, MT, about 20 miles northwest of Helena. The research should determine the nature and size of the resource, how the energy might be extracted, the potential monetary value of the energy, and how similar resources elsewhere might be located. The heat source was expected to be a granitic pluton or magmatic intrusion, 10,000 to 40,000 years old, with temperatures in the range of 300 to 500°C. Originally it was thought that the pluton was at relatively shallow depths, but at present its depth and exact location are unknown Close

• 6. [Image] Washington: A Guide to Geothermal Energy Development

  	A brief overview is given of the geological characteristics of each region of the state as they relate to potential geothermal development. Those exploration methods which can lead to the siting of a deep ...
  	Citation × Citation Citation Abstract Copy Title: Washington: A Guide to Geothermal Energy Development Author: Bloomquist, R.G. Year: 1980 A brief overview is given of the geological characteristics of each region of the state as they relate to potential geothermal development. Those exploration methods which can lead to the siting of a deep exploration well are described. Requirements and techniques needed for drilling deeper higher temperature exploration and production wells are presented. Electrical generation, direct utilization, and indirect utilization are reviewed. Economic factors of direct use projects are presented. A general guide to the regulatory framework affecting geothermal energy development is provided. The general steps necessary to gain access to explore, develop, distribute, and use geothermal resources are outlined (MHR) Title: Washington: A Guide to Geothermal Energy Development Author: Bloomquist, R.G. Year: 1980 A brief overview is given of the geological characteristics of each region of the state as they relate to potential geothermal development. Those exploration methods which can lead to the siting of a deep exploration well are described. Requirements and techniques needed for drilling deeper higher temperature exploration and production wells are presented. Electrical generation, direct utilization, and indirect utilization are reviewed. Economic factors of direct use projects are presented. A general guide to the regulatory framework affecting geothermal energy development is provided. The general steps necessary to gain access to explore, develop, distribute, and use geothermal resources are outlined (MHR) Close

• 7. [Image] Economic factors relevant for electric power produced from hot dry rock geothermal resources: a case study for the Fenton Hill, New Mexico, area

  	The case study described here concerns an HDR system which provides geothermal fluids for a hypothetical electric plant located in the Fenton Hill area in New Mexico's Jemez Mountains. Primary concern ...
  	Citation × Citation Citation Abstract Copy Title: Economic factors relevant for electric power produced from hot dry rock geothermal resources: a case study for the Fenton Hill, New Mexico, area Author: Cummings, R.G Year: 1979 The case study described here concerns an HDR system which provides geothermal fluids for a hypothetical electric plant located in the Fenton Hill area in New Mexico's Jemez Mountains. Primary concern is focused on the implications of differing drilling conditions, as reflected by costs, and differing risk environments for the potential commercialization of an HDR system. Drilling costs for best, medium and worst drilling conditions are taken from a recent study of drilling costs for HDR systems. Differing risk environments are represented by differing rate-of-return requirements on stocks and interest on bonds which the HDR system is assumed to pay; rate of return/interest combinations considered are 6%/3%, 9%/6%, 12%/9% and 15%/12%. The method of analysis used here is that of determining the minimum busbar cost for electricity for this case study wherein all costs are expressed in annual equivalent terms. The minimum cost design for the electric generating plant is determined jointly with the minimum cost design for the HDR system. The interdependence between minimum cost designs for the plant and HDR system is given specific attention; the optimum design temperature for the plant is shown here to be lower than one might expect for conventional power plants - in the range 225/sup 0/ to 265/sup 0/C. Major results from the analyses of HDR-produced electricity in the Fenton Hill area are as follows. With real, inflation-free debt/equity rates of 6% and 9%, respectively, the minimum busbar cost is shown to lie in the range 18 to 29 mills/kwh. When real debt/equity rates rise to 12% and 15%, busbar costs rise to 24 to 39 mills/kwh.; DOE/ET/27017-T1 Title: Economic factors relevant for electric power produced from hot dry rock geothermal resources: a case study for the Fenton Hill, New Mexico, area Author: Cummings, R.G Year: 1979 The case study described here concerns an HDR system which provides geothermal fluids for a hypothetical electric plant located in the Fenton Hill area in New Mexico's Jemez Mountains. Primary concern is focused on the implications of differing drilling conditions, as reflected by costs, and differing risk environments for the potential commercialization of an HDR system. Drilling costs for best, medium and worst drilling conditions are taken from a recent study of drilling costs for HDR systems. Differing risk environments are represented by differing rate-of-return requirements on stocks and interest on bonds which the HDR system is assumed to pay; rate of return/interest combinations considered are 6%/3%, 9%/6%, 12%/9% and 15%/12%. The method of analysis used here is that of determining the minimum busbar cost for electricity for this case study wherein all costs are expressed in annual equivalent terms. The minimum cost design for the electric generating plant is determined jointly with the minimum cost design for the HDR system. The interdependence between minimum cost designs for the plant and HDR system is given specific attention; the optimum design temperature for the plant is shown here to be lower than one might expect for conventional power plants - in the range 225/sup 0/ to 265/sup 0/C. Major results from the analyses of HDR-produced electricity in the Fenton Hill area are as follows. With real, inflation-free debt/equity rates of 6% and 9%, respectively, the minimum busbar cost is shown to lie in the range 18 to 29 mills/kwh. When real debt/equity rates rise to 12% and 15%, busbar costs rise to 24 to 39 mills/kwh.; DOE/ET/27017-T1 Close