Search

Search Results

• 1. [Image] Steady-State and Transient Wellbore Temperatures during Drilling

  	An extensive literature search was made to locate technical publications and computer programs relating to wellbore temperatures during drilling operations. The search confirmed the need for knowledge ...
  	Citation × Citation Citation Abstract Copy Title: Steady-State and Transient Wellbore Temperatures during Drilling Author: McDonald, W.J. Year: 1976 An extensive literature search was made to locate technical publications and computer programs relating to wellbore temperatures during drilling operations. The search confirmed the need for knowledge of transient and steady state circulating temperatures in the design of geothermal bits. Two approaches were used in calculating borehole temperatures. The steady state solution of Holmes and Swift was programmed and 2100 cases calculated for various borehole configurations. For transient temperature studies, calculations were made for ten borehole configurations. These calculations help emphasize the need for better high temperature bit performance and improved engineering procedures in drilling. The conclusions and recommendations are based on latest available technology for calculating wellbore temperatures Title: Steady-State and Transient Wellbore Temperatures during Drilling Author: McDonald, W.J. Year: 1976 An extensive literature search was made to locate technical publications and computer programs relating to wellbore temperatures during drilling operations. The search confirmed the need for knowledge of transient and steady state circulating temperatures in the design of geothermal bits. Two approaches were used in calculating borehole temperatures. The steady state solution of Holmes and Swift was programmed and 2100 cases calculated for various borehole configurations. For transient temperature studies, calculations were made for ten borehole configurations. These calculations help emphasize the need for better high temperature bit performance and improved engineering procedures in drilling. The conclusions and recommendations are based on latest available technology for calculating wellbore temperatures Close

• 2. [Image] Geological and Geophysical Analysis of Coso Geothermal Exploration Hole No. 1 (CGEH-1), Coso Hot Springs KGRA, California

  	The Coso Geothermal Exploration Hole number one (CGEH-1) was drilled in the Coso Hot Springs KGRA, California, from September 2 to December 2, 1977. Chip samples were collected at ten foot intervals and ...
  	Citation × Citation Citation Abstract Copy Title: Geological and Geophysical Analysis of Coso Geothermal Exploration Hole No. 1 (CGEH-1), Coso Hot Springs KGRA, California Author: Galbraith, R.M. Year: 1978 The Coso Geothermal Exploration Hole number one (CGEH-1) was drilled in the Coso Hot Springs KGRA, California, from September 2 to December 2, 1977. Chip samples were collected at ten foot intervals and extensive geophysical logging surveys were conducted to document the geologic character of the geothermal system as penetrated by CGEH-1. The major rock units encountered include a mafic metamorphic sequence and a leucogranite which intruded the metamorphic rocks. Only weak hydrothermal alteration was noted in these rocks. Drillhole surveys and drilling rate data indicate that the geothermal system is structurally controlled and that the drillhole itself was strongly influenced by structural zones. Water chemistry indicates that this geothermal resource is a hot-water rather than a vapor-dominated system. Several geophysical logs were employed to characterize the drillhole geology. The natural gamma and neutron porosity logs indicate gross rock type and the acoustics logs indicate fractured rock and potentially permeable zones. A series of temperature logs run as a function of time during and after the completion of drilling were most useful in delineating the zones of maximum heat flux. Convective heat flow and temperatures greater than 350/sup 0/F appear to occur only along an open fracture system encountered between depths of 1850 and 2775 feet. Temperature logs indicate a negative thermal gradient below 3000 feet Title: Geological and Geophysical Analysis of Coso Geothermal Exploration Hole No. 1 (CGEH-1), Coso Hot Springs KGRA, California Author: Galbraith, R.M. Year: 1978 The Coso Geothermal Exploration Hole number one (CGEH-1) was drilled in the Coso Hot Springs KGRA, California, from September 2 to December 2, 1977. Chip samples were collected at ten foot intervals and extensive geophysical logging surveys were conducted to document the geologic character of the geothermal system as penetrated by CGEH-1. The major rock units encountered include a mafic metamorphic sequence and a leucogranite which intruded the metamorphic rocks. Only weak hydrothermal alteration was noted in these rocks. Drillhole surveys and drilling rate data indicate that the geothermal system is structurally controlled and that the drillhole itself was strongly influenced by structural zones. Water chemistry indicates that this geothermal resource is a hot-water rather than a vapor-dominated system. Several geophysical logs were employed to characterize the drillhole geology. The natural gamma and neutron porosity logs indicate gross rock type and the acoustics logs indicate fractured rock and potentially permeable zones. A series of temperature logs run as a function of time during and after the completion of drilling were most useful in delineating the zones of maximum heat flux. Convective heat flow and temperatures greater than 350/sup 0/F appear to occur only along an open fracture system encountered between depths of 1850 and 2775 feet. Temperature logs indicate a negative thermal gradient below 3000 feet Close

• 3. [Image] Planning, Drilling, Logging, and Testing of Energy Extraction Hole EE-1, Phases I and II

  	Energy Extraction Hole No. 1 (EE-1) is the second deep hole drilled into the Precambrian-age granitic rocks of the Jemez Mountains of north-central New Mexico. EE-1 was drilled to intersect a hydraulic ...
  	Citation × Citation Citation Abstract Copy Title: Planning, Drilling, Logging, and Testing of Energy Extraction Hole EE-1, Phases I and II Author: Pettitt, R.A. Year: 1977 Energy Extraction Hole No. 1 (EE-1) is the second deep hole drilled into the Precambrian-age granitic rocks of the Jemez Mountains of north-central New Mexico. EE-1 was drilled to intersect a hydraulic fracture extending outward from near the bottom of previously drilled hole GT-2, thus completing the underground circulation loop required for the hot dry rock geothermal energy extraction experiment. Directional drilling techniques were used to intersect the fracture zone. In addition, high-temperature instrumentation and equipment development, hydraulic fracturing experiments, pressure-flow testing of the fracture systems, and fracture mapping and borehole-ranging technique activities were conducted. The drilling, logging, and testing operations in EE-1 are described Title: Planning, Drilling, Logging, and Testing of Energy Extraction Hole EE-1, Phases I and II Author: Pettitt, R.A. Year: 1977 Energy Extraction Hole No. 1 (EE-1) is the second deep hole drilled into the Precambrian-age granitic rocks of the Jemez Mountains of north-central New Mexico. EE-1 was drilled to intersect a hydraulic fracture extending outward from near the bottom of previously drilled hole GT-2, thus completing the underground circulation loop required for the hot dry rock geothermal energy extraction experiment. Directional drilling techniques were used to intersect the fracture zone. In addition, high-temperature instrumentation and equipment development, hydraulic fracturing experiments, pressure-flow testing of the fracture systems, and fracture mapping and borehole-ranging technique activities were conducted. The drilling, logging, and testing operations in EE-1 are described Close