Search

Search Results

• 1. [Article] Estimation of Transient Temperature Distribution during Quenching, via a Parabolic Model

  A material-independent model to estimate the transient temperature distribution in a test probe quenched by immersion is presented in this study. This model is based on the assumption that, under one-dimensional ...

  Citation × Citation Citation Abstract Copy Title: Estimation of Transient Temperature Distribution during Quenching, via a Parabolic Model Author: Lozano, Diego E., Martinez-Solis, Gabriela, Mercado-Solis, Rafael David, Colás, Rafael, Totten, George E. Year: 2015 A material-independent model to estimate the transient temperature distribution in a test probe quenched by immersion is presented in this study. This model is based on the assumption that, under one-dimensional unsteady heat conduction, the radial temperature distribution at the end of an interval belongs to the equation of a parabola. The model was validated using AISI 304 stainless steel test probes (Φ8×40 mm and Φ12×60 mm) quenched from 850 to 900 °C in water and in water-based NaNO2 solutions at 25 °C and in canola oil at 50 °C. Additionally, square test probes (20×20×100 mm) were quenched from 550 °C in water. The test probes were equipped with embedded thermocouples for temperature-versus-time data logging at the core, one-quarter thickness and 1 mm below the surface. In each experiment, the data recordings from the core and near-surface thermocouples were employed for the temperature calculations while the data from the one-quarter thickness thermocouple were employed for model validity verifications. In all cases, the calculated temperature distributions showed good correlations with the experimentally obtained values. Based on the results of this work, it is concluded that this approach constitutes a simple, quick and efficient tool for estimating transient surface and radial temperature distributions and represents a useful resource for quenchant cooling rate calculations and heat transfer characterizations. Title: Estimation of Transient Temperature Distribution during Quenching, via a Parabolic Model Author: Lozano, Diego E., Martinez-Solis, Gabriela, Mercado-Solis, Rafael David, Colás, Rafael, Totten, George E. Year: 2015 A material-independent model to estimate the transient temperature distribution in a test probe quenched by immersion is presented in this study. This model is based on the assumption that, under one-dimensional unsteady heat conduction, the radial temperature distribution at the end of an interval belongs to the equation of a parabola. The model was validated using AISI 304 stainless steel test probes (Φ8×40 mm and Φ12×60 mm) quenched from 850 to 900 °C in water and in water-based NaNO2 solutions at 25 °C and in canola oil at 50 °C. Additionally, square test probes (20×20×100 mm) were quenched from 550 °C in water. The test probes were equipped with embedded thermocouples for temperature-versus-time data logging at the core, one-quarter thickness and 1 mm below the surface. In each experiment, the data recordings from the core and near-surface thermocouples were employed for the temperature calculations while the data from the one-quarter thickness thermocouple were employed for model validity verifications. In all cases, the calculated temperature distributions showed good correlations with the experimentally obtained values. Based on the results of this work, it is concluded that this approach constitutes a simple, quick and efficient tool for estimating transient surface and radial temperature distributions and represents a useful resource for quenchant cooling rate calculations and heat transfer characterizations. Close

• 2. [Article] High-Speed Quenching of High Carbon Steel

  Medium and high carbon steels are usually quenched in polymer and oil in order to avoid cracking and distortion; however, recent studies have proved that it is possible to minimize cracking using water ...

  Citation × Citation Citation Abstract Copy Title: High-Speed Quenching of High Carbon Steel Author: Martínez-Cázares, Gabriela M., Lozano, Diego E., Guerrero-Mata, Martha, Colás, Rafael, Totten, George E. Year: 2014 Medium and high carbon steels are usually quenched in polymer and oil in order to avoid cracking and distortion; however, recent studies have proved that it is possible to minimize cracking using water as a coolant of these steels by promoting extremely high cooling rates. By great agitation and velocity of quenchant, the vapor blanket is reduced or prevented during water quench, allowing uniform hardening of the surface. In this study, the cooling severity of a spray quenching system and a high-speed quenching chamber are studied. Cylindrical samples of AISI 304 stainless steel (20 mm in diameter and 100 mm length) were employed to characterize the cooling severity. Thermal data was acquired through K-type thermocouples placed in the sample at three positions, 1 mm below surface, mid-radius and at center of the specimen, connected to a data acquisition system. High thermal gradients were observed in both systems, being the high-speed chamber the severest cooling. The maximum cooling rate obtained at the surface was 470 and 300°C/s for the high-speed chamber and the spray system, respectively. In addition, 5160 spring steel samples were quenched for short times in both systems; the cooling was interrupted to avoid through transformation and to produce a case-core type microstructure. Different cooling times were used for the interrupted quenching to modify the martensite case thickness. No cracks were observed. Thermal results and microstructures are discussed. Title: High-Speed Quenching of High Carbon Steel Author: Martínez-Cázares, Gabriela M., Lozano, Diego E., Guerrero-Mata, Martha, Colás, Rafael, Totten, George E. Year: 2014 Medium and high carbon steels are usually quenched in polymer and oil in order to avoid cracking and distortion; however, recent studies have proved that it is possible to minimize cracking using water as a coolant of these steels by promoting extremely high cooling rates. By great agitation and velocity of quenchant, the vapor blanket is reduced or prevented during water quench, allowing uniform hardening of the surface. In this study, the cooling severity of a spray quenching system and a high-speed quenching chamber are studied. Cylindrical samples of AISI 304 stainless steel (20 mm in diameter and 100 mm length) were employed to characterize the cooling severity. Thermal data was acquired through K-type thermocouples placed in the sample at three positions, 1 mm below surface, mid-radius and at center of the specimen, connected to a data acquisition system. High thermal gradients were observed in both systems, being the high-speed chamber the severest cooling. The maximum cooling rate obtained at the surface was 470 and 300°C/s for the high-speed chamber and the spray system, respectively. In addition, 5160 spring steel samples were quenched for short times in both systems; the cooling was interrupted to avoid through transformation and to produce a case-core type microstructure. Different cooling times were used for the interrupted quenching to modify the martensite case thickness. No cracks were observed. Thermal results and microstructures are discussed. Close