Search

Search Results

• 1. [Article] Laurance Lake Temperature Model

  Laurance Lake is a reservoir located in Hood River County, Oregon (Figure 1). It is located at the base on Mt. Hood in Oregon (see Figure 2 and Figure 3), discharges into the Middle Fork of the Hood River. ...

  Citation × Citation Citation Abstract Copy Title: Laurance Lake Temperature Model Author: Berger, Chris, Wells, Scott A., Annear, Robert Leslie Year: 2005 Laurance Lake is a reservoir located in Hood River County, Oregon (Figure 1). It is located at the base on Mt. Hood in Oregon (see Figure 2 and Figure 3), discharges into the Middle Fork of the Hood River. The reservoir was constructed in 1968 for irrigation storage and has a capacity 3564 acre- feet at full pool. Since the river vio lates temperature standards, this study has been designed to construct a hydrodynamic and temperature model of Laurance reservoir in order to assess strategies for improving temperatures in the Middle Fork River. The objectives of the study are then to Develop a hydrodynamic and temperature model of Laurance Lake Calibrate the model to field data collected from November 2002 through Spring 2004 Use the model to evaluate strategies for temperature improvement through operational or structural changes to Lake Laurance The model chosen for development was CE-QUAL-W2 Version 3.2 (Cole and Wells, 2004). This is a two-dimensional unsteady hydrodynamic, temperature and water quality model that includes typical eutrophication parameters (algae, nutrients, temperature, organic matter, dissolved oxygen, pH). PSU, under the support of the Corps of Engineers Waterways Experiment Station, is a center for development of this modeling tool. Title: Laurance Lake Temperature Model Author: Berger, Chris, Wells, Scott A., Annear, Robert Leslie Year: 2005 Laurance Lake is a reservoir located in Hood River County, Oregon (Figure 1). It is located at the base on Mt. Hood in Oregon (see Figure 2 and Figure 3), discharges into the Middle Fork of the Hood River. The reservoir was constructed in 1968 for irrigation storage and has a capacity 3564 acre- feet at full pool. Since the river vio lates temperature standards, this study has been designed to construct a hydrodynamic and temperature model of Laurance reservoir in order to assess strategies for improving temperatures in the Middle Fork River. The objectives of the study are then to Develop a hydrodynamic and temperature model of Laurance Lake Calibrate the model to field data collected from November 2002 through Spring 2004 Use the model to evaluate strategies for temperature improvement through operational or structural changes to Lake Laurance The model chosen for development was CE-QUAL-W2 Version 3.2 (Cole and Wells, 2004). This is a two-dimensional unsteady hydrodynamic, temperature and water quality model that includes typical eutrophication parameters (algae, nutrients, temperature, organic matter, dissolved oxygen, pH). PSU, under the support of the Corps of Engineers Waterways Experiment Station, is a center for development of this modeling tool. Close

• 2. [Article] Modeling Effects of Channel Complexity and Hyporheic Flow on Stream Temperatures

  Stream temperatures are affected by multiple forcing functions, including surface heat exchange (including solar radiation, evaporation, conduction, and net long wave radiation) and hyporheic flows. Each ...

  Citation × Citation Citation Abstract Copy Title: Modeling Effects of Channel Complexity and Hyporheic Flow on Stream Temperatures Author: Berger, Chris, Wells, Scott A. Year: 2007 Stream temperatures are affected by multiple forcing functions, including surface heat exchange (including solar radiation, evaporation, conduction, and net long wave radiation) and hyporheic flows. Each of these forcing functions is directly influenced by the level of channel complexity in the stream channel and riparian shading. The interrelationship between channel complexity, hyporheic flow and stream temperature is highly complex, and efforts to manage for habitat diversity by managing channel complexity could result in unintended consequences on stream temperature. When planning modifications to stream channel complexity, consideration should be given to the effects such moderations could have on stream temperatures. Urbanization has impacted many steams due to the construction of bank protections, levees, vegetation removal, etc. Such activities have eliminated side channels and reduced stream braiding, thereby reducing the overall channel complexity. Hulse et al. (2002) developed maps showing the channel configurations of the Willamette River in Oregon, USA in the years 1850 and 1995. These maps show a significant reduction in channel complexity in the intervening years. More complex stream channels provide greater habitat diversity and thus, are generally more desirable from a wildlife management perspective. Therefore, management of streams for increased channel complexity is gaining in popularity. Knowing that stream channel complexity has diminished over time, an important question to consider is ‘what were stream temperatures before we altered the natural channels?’ This is an important issue in determining what natural conditions were and how we have strayed from these so-called ‘natural’ conditions as a result of channelization, dam building, and changes to the riparian vegetation and deforestation. Current Total Maximum Daily Load’s (TMDL) rely on determining a ‘natural’ condition. In order to develop an understanding of what that is, a hydrodynamic and water quality computer simulation model has been applied to Oregon’s Willamette River with several levels of channel complexity and varying rates of hyporheic flows. Adapting the model used to develop TMDL’s for temperature in the Willamette River, the effects of present and past channel complexity on water temperatures was determined. The model used to develop the TMDL was the U. S. Army Corps of Engineers dynamic 2-D model CE-QUAL-W2, which consists of directly coupled hydrodynamic and water quality transport models and simulates parameters such as temperature, algae concentration, dissolved oxygen concentration, pH, nutrient concentrations and residence time. The model also incorporates a dynamic shading algorithm for both vegetative and topographic shading on water bodies. Title: Modeling Effects of Channel Complexity and Hyporheic Flow on Stream Temperatures Author: Berger, Chris, Wells, Scott A. Year: 2007 Stream temperatures are affected by multiple forcing functions, including surface heat exchange (including solar radiation, evaporation, conduction, and net long wave radiation) and hyporheic flows. Each of these forcing functions is directly influenced by the level of channel complexity in the stream channel and riparian shading. The interrelationship between channel complexity, hyporheic flow and stream temperature is highly complex, and efforts to manage for habitat diversity by managing channel complexity could result in unintended consequences on stream temperature. When planning modifications to stream channel complexity, consideration should be given to the effects such moderations could have on stream temperatures. Urbanization has impacted many steams due to the construction of bank protections, levees, vegetation removal, etc. Such activities have eliminated side channels and reduced stream braiding, thereby reducing the overall channel complexity. Hulse et al. (2002) developed maps showing the channel configurations of the Willamette River in Oregon, USA in the years 1850 and 1995. These maps show a significant reduction in channel complexity in the intervening years. More complex stream channels provide greater habitat diversity and thus, are generally more desirable from a wildlife management perspective. Therefore, management of streams for increased channel complexity is gaining in popularity. Knowing that stream channel complexity has diminished over time, an important question to consider is ‘what were stream temperatures before we altered the natural channels?’ This is an important issue in determining what natural conditions were and how we have strayed from these so-called ‘natural’ conditions as a result of channelization, dam building, and changes to the riparian vegetation and deforestation. Current Total Maximum Daily Load’s (TMDL) rely on determining a ‘natural’ condition. In order to develop an understanding of what that is, a hydrodynamic and water quality computer simulation model has been applied to Oregon’s Willamette River with several levels of channel complexity and varying rates of hyporheic flows. Adapting the model used to develop TMDL’s for temperature in the Willamette River, the effects of present and past channel complexity on water temperatures was determined. The model used to develop the TMDL was the U. S. Army Corps of Engineers dynamic 2-D model CE-QUAL-W2, which consists of directly coupled hydrodynamic and water quality transport models and simulates parameters such as temperature, algae concentration, dissolved oxygen concentration, pH, nutrient concentrations and residence time. The model also incorporates a dynamic shading algorithm for both vegetative and topographic shading on water bodies. Close

• 3. [Article] Willamette River Basin Temperature TMDL Model: Model Calibration

  The State of Oregon Department of Environmental Quality (DEQ) is developing a TMDL for temperature in the Willamette River basin shown in Figure 1. The study area included the Willamette River and all ...

  Citation × Citation Citation Abstract Copy Title: Willamette River Basin Temperature TMDL Model: Model Calibration Author: Berger, Chris, McKillip, Michael Lee, Annear, Robert Leslie, Khan, Sher Jamal, Wells, Scott A. Year: 2004 The State of Oregon Department of Environmental Quality (DEQ) is developing a TMDL for temperature in the Willamette River basin shown in Figure 1. The study area included the Willamette River and all major tributaries (except the Tualatin River where a TMDL process was already concluded). A large section of the Columbia River was also modeled to provide adequate boundary representation of tidal flows in the lower Willamette River. The Willamette River below the Oregon City Falls in the Portland metropolitan area has a typical diurnal tidal range of 1 m. The development of a dynamic model of temperature and hydrodynamics of the entire river basin incorporating shading were primary requirements of this modeling study. The model would be used by DEQ to set temperature limits on point source dischargers and to evaluate the impact of management strategies on river temperatures to improve fish habitat. Some of these strategies included modifications of the dam at the Willamette River Falls south of Portland and channel reconfigurations. The river basin model was originally divided into several reaches. Individual models were developed for each reach. The models were set-up for each section of the Willamette basin as described in Annear et al. (2004a), the models were calibrated to field data and management strategies were evaluated as described in Annear et al (2004b). This report outlines the model calibration of each of these model sections or elements for both the calibration time periods. The calibration period for each model section differs due to the availability of boundary condition data. The model management simulation scenarios (Annear et al, 2004b) also required boundary condition data that extended past the calibration periods. Title: Willamette River Basin Temperature TMDL Model: Model Calibration Author: Berger, Chris, McKillip, Michael Lee, Annear, Robert Leslie, Khan, Sher Jamal, Wells, Scott A. Year: 2004 The State of Oregon Department of Environmental Quality (DEQ) is developing a TMDL for temperature in the Willamette River basin shown in Figure 1. The study area included the Willamette River and all major tributaries (except the Tualatin River where a TMDL process was already concluded). A large section of the Columbia River was also modeled to provide adequate boundary representation of tidal flows in the lower Willamette River. The Willamette River below the Oregon City Falls in the Portland metropolitan area has a typical diurnal tidal range of 1 m. The development of a dynamic model of temperature and hydrodynamics of the entire river basin incorporating shading were primary requirements of this modeling study. The model would be used by DEQ to set temperature limits on point source dischargers and to evaluate the impact of management strategies on river temperatures to improve fish habitat. Some of these strategies included modifications of the dam at the Willamette River Falls south of Portland and channel reconfigurations. The river basin model was originally divided into several reaches. Individual models were developed for each reach. The models were set-up for each section of the Willamette basin as described in Annear et al. (2004a), the models were calibrated to field data and management strategies were evaluated as described in Annear et al (2004b). This report outlines the model calibration of each of these model sections or elements for both the calibration time periods. The calibration period for each model section differs due to the availability of boundary condition data. The model management simulation scenarios (Annear et al, 2004b) also required boundary condition data that extended past the calibration periods. Close

• 4. [Article] Willamette River Basin Temperature TMDL Model: Model Scenarios

  The State of Oregon Department of Environmental Quality (DEQ) is developing a TMDL for temperature in the Willamette River basin shown in Figure 1. The study area included the Willamette River and all ...

  Citation × Citation Citation Abstract Copy Title: Willamette River Basin Temperature TMDL Model: Model Scenarios Author: Annear, Robert Leslie, McKillip, Michael Lee, Khan, Sher Jamal, Berger, Chris, Wells, Scott A. Year: 2004 The State of Oregon Department of Environmental Quality (DEQ) is developing a TMDL for temperature in the Willamette River basin shown in Figure 1. The study area included the Willamette River and all major tributaries (except the Tualatin River where a TMDL process was already concluded). A large section of the Columbia River was also modeled to provide adequate boundary representation of tidal flows in the lower Willamette River. The Willamette River below the Oregon City Falls in the Portland metropolitan area has a typical diurnal tidal range of 1 m. The development of a dynamic model of temperature and hydrodynamics of the entire river basin incorporating shading were primary requirements of this modeling study. The model would be used by DEQ to set temperature limits on point source dischargers and to evaluate the impact of management strategies on river temperatures to improve fish habitat. Some of these strategies included modifications of the dam at the Willamette River Falls south of Portland and channel reconfigurations. Once the models were set-up for each section of the Willamette basin, the model was calibrated to field data and management strategies were evaluated. These are the subjects of two other reports: Annear et al. (2004) and Berger et al. (2004). This report outlines the results of implementing model scenarios for each of the model sections or elements for specific time periods. The model scenario simulation periods used to investigate management scenarios required boundary condition data that extended past the model calibration periods. The model simulation period for year 2001 was from June 1 to October 31 and for year 2002 from April 1 to October 31. Title: Willamette River Basin Temperature TMDL Model: Model Scenarios Author: Annear, Robert Leslie, McKillip, Michael Lee, Khan, Sher Jamal, Berger, Chris, Wells, Scott A. Year: 2004 The State of Oregon Department of Environmental Quality (DEQ) is developing a TMDL for temperature in the Willamette River basin shown in Figure 1. The study area included the Willamette River and all major tributaries (except the Tualatin River where a TMDL process was already concluded). A large section of the Columbia River was also modeled to provide adequate boundary representation of tidal flows in the lower Willamette River. The Willamette River below the Oregon City Falls in the Portland metropolitan area has a typical diurnal tidal range of 1 m. The development of a dynamic model of temperature and hydrodynamics of the entire river basin incorporating shading were primary requirements of this modeling study. The model would be used by DEQ to set temperature limits on point source dischargers and to evaluate the impact of management strategies on river temperatures to improve fish habitat. Some of these strategies included modifications of the dam at the Willamette River Falls south of Portland and channel reconfigurations. Once the models were set-up for each section of the Willamette basin, the model was calibrated to field data and management strategies were evaluated. These are the subjects of two other reports: Annear et al. (2004) and Berger et al. (2004). This report outlines the results of implementing model scenarios for each of the model sections or elements for specific time periods. The model scenario simulation periods used to investigate management scenarios required boundary condition data that extended past the model calibration periods. The model simulation period for year 2001 was from June 1 to October 31 and for year 2002 from April 1 to October 31. Close

• 5. [Article] Willamette River Basin Temperature TMDL Model: Boundary Conditions and Model Setup

  The State of Oregon Department of Environmental Quality (DEQ) is developing a TMDL for temperature in the Willamette River basin shown in Figure 1. The study area included the Willamette River and all ...

  Citation × Citation Citation Abstract Copy Title: Willamette River Basin Temperature TMDL Model: Boundary Conditions and Model Setup Author: Annear, Robert Leslie, McKillip, Michael Lee, Khan, Sher Jamal, Berger, Chris, Wells, Scott A. Year: 2004 The State of Oregon Department of Environmental Quality (DEQ) is developing a TMDL for temperature in the Willamette River basin shown in Figure 1. The study area included the Willamette River and all major tributaries (except the Tualatin River where a TMDL process was already concluded). A large section of the Columbia River was also modeled to provide adequate boundary representation of tidal flows in the lower Willamette River. The Willamette River below the Oregon City Falls in the Portland metropolitan area has a typical diurnal tidal range of 1 m. The development of a dynamic model of temperature and hydrodynamics of the entire river basin incorporating shading were primary requirements of this modeling study. The model would be used by DEQ to set temperature limits on point source dischargers and to evaluate the impact of management strategies on river temperatures to improve fish habitat. Some of these strategies included modifications of the dam at the Willamette River Falls south of Portland and channel reconfigurations. Once the models were set-up for each section of the Willamette basin, the model was calibrated to field data and management strategies were evaluated. These are the subjects of two other reports: Annear et al. (2004b) and Berger et al. (2004). This report outlines the model development of each of these model sections or elements for both the calibration time periods and the management scenario time periods. The calibration period for each model section differs due to the availability of boundary condition data. The model simulation periods used to investigate management scenarios (Annear et al, 2004b) also required boundary condition data that extended past the calibration periods. Title: Willamette River Basin Temperature TMDL Model: Boundary Conditions and Model Setup Author: Annear, Robert Leslie, McKillip, Michael Lee, Khan, Sher Jamal, Berger, Chris, Wells, Scott A. Year: 2004 The State of Oregon Department of Environmental Quality (DEQ) is developing a TMDL for temperature in the Willamette River basin shown in Figure 1. The study area included the Willamette River and all major tributaries (except the Tualatin River where a TMDL process was already concluded). A large section of the Columbia River was also modeled to provide adequate boundary representation of tidal flows in the lower Willamette River. The Willamette River below the Oregon City Falls in the Portland metropolitan area has a typical diurnal tidal range of 1 m. The development of a dynamic model of temperature and hydrodynamics of the entire river basin incorporating shading were primary requirements of this modeling study. The model would be used by DEQ to set temperature limits on point source dischargers and to evaluate the impact of management strategies on river temperatures to improve fish habitat. Some of these strategies included modifications of the dam at the Willamette River Falls south of Portland and channel reconfigurations. Once the models were set-up for each section of the Willamette basin, the model was calibrated to field data and management strategies were evaluated. These are the subjects of two other reports: Annear et al. (2004b) and Berger et al. (2004). This report outlines the model development of each of these model sections or elements for both the calibration time periods and the management scenario time periods. The calibration period for each model section differs due to the availability of boundary condition data. The model simulation periods used to investigate management scenarios (Annear et al, 2004b) also required boundary condition data that extended past the calibration periods. Close

• 6. [Article] Idaho Pend Oreille River Model: Model Development and Calibration

  The objectives of this project were to: • Develop a hydrodynamic and temperature model of Pend Oreille River using CE-QUAL-W2 Version 3.2 • Calibrate the CE-QUAL-W2 model to field data collected during ...

  Citation × Citation Citation Abstract Copy Title: Idaho Pend Oreille River Model: Model Development and Calibration Author: Annear, Robert Leslie, Berger, Chris, Wells, Scott A. Year: 2006 The objectives of this project were to: • Develop a hydrodynamic and temperature model of Pend Oreille River using CE-QUAL-W2 Version 3.2 • Calibrate the CE-QUAL-W2 model to field data collected during 2004 and 2005 using the following water quality variables: flow, water surface elevation, and velocity temperature o dissolved oxygen nutrients (NO3-N+NO2-N, NH4-N, PO4-P) algae – chlorophyll a BOD5 and dissolved organic matter and particulate organic matter compartments (both labile and refractory) for the organic matter cycling with algae periphyton The model chosen for development was CE-QUAL-W2 Version 3.2 (Cole and Wells, 2004). This is a two-dimensional unsteady hydrodynamic and water quality model that includes typical eutrophication constituents (algae, nutrients, temperature, organic matter, dissolved oxygen, pH). Portland State University’s Water Quality Research Group is a center for development of this modeling tool (see http://www.cee.pdx.edu/w2). The model simulation was run from January 1st, 2004 to September 25th, 2005. The calibration period focused on the summers during each year when water quality data were obtained. Title: Idaho Pend Oreille River Model: Model Development and Calibration Author: Annear, Robert Leslie, Berger, Chris, Wells, Scott A. Year: 2006 The objectives of this project were to: • Develop a hydrodynamic and temperature model of Pend Oreille River using CE-QUAL-W2 Version 3.2 • Calibrate the CE-QUAL-W2 model to field data collected during 2004 and 2005 using the following water quality variables: flow, water surface elevation, and velocity temperature o dissolved oxygen nutrients (NO3-N+NO2-N, NH4-N, PO4-P) algae – chlorophyll a BOD5 and dissolved organic matter and particulate organic matter compartments (both labile and refractory) for the organic matter cycling with algae periphyton The model chosen for development was CE-QUAL-W2 Version 3.2 (Cole and Wells, 2004). This is a two-dimensional unsteady hydrodynamic and water quality model that includes typical eutrophication constituents (algae, nutrients, temperature, organic matter, dissolved oxygen, pH). Portland State University’s Water Quality Research Group is a center for development of this modeling tool (see http://www.cee.pdx.edu/w2). The model simulation was run from January 1st, 2004 to September 25th, 2005. The calibration period focused on the summers during each year when water quality data were obtained. Close

• 7. [Article] Pend Oreille River, Box Canyon Model: Model Scenario Simulations

  The Washington Department of Ecology is interested in developing a temperature Total Maximum Daily Load (TMDL) allocation for the Pend Oreille River between the Albeni Falls Dam (U.S. Army Corps of Engineer’s ...

  Citation × Citation Citation Abstract Copy Title: Pend Oreille River, Box Canyon Model: Model Scenario Simulations Author: Berger, Chris, Annear, Robert Leslie, Wells, Scott A. Year: 2007 The Washington Department of Ecology is interested in developing a temperature Total Maximum Daily Load (TMDL) allocation for the Pend Oreille River between the Albeni Falls Dam (U.S. Army Corps of Engineer’s reservoir) and Box Canyon Dam as shown in Figure 1. The Pend Oreille drainage basin is shown in Figure 2. An existing model of the Box Canyon reach was updated from CE-QUALW2 Version 3.0 to Version 3.5. This current research involves improving the calibration of the original model (1997 and 1998) and expanding the model using 2004 as an additional data set for calibration. The use of field data from 2004 as an additional calibration year was chosen to improve the confidence in the model’s predictive ability for temperature. Hence, the model simulations were run from January 1st to December 31st in each of the 3 years of model simulation: 1997, 1998 and 2004. The model chosen for development is CE-QUAL-W2 Version 3.5 (Cole and Wells, 2006). This is a twodimensional unsteady hydrodynamic and water quality model that includes typical eutrophication parameters (algae, nutrients, temperature, organic matter, dissolved oxygen, pH). The PSU-WQRG (Water Quality Research Group) is a center for development of this modeling tool (see http://www.cee.pdx.edu/w2). The model simulation for scenarios was run from January 1st, 2004 to September 25th, 2005. Title: Pend Oreille River, Box Canyon Model: Model Scenario Simulations Author: Berger, Chris, Annear, Robert Leslie, Wells, Scott A. Year: 2007 The Washington Department of Ecology is interested in developing a temperature Total Maximum Daily Load (TMDL) allocation for the Pend Oreille River between the Albeni Falls Dam (U.S. Army Corps of Engineer’s reservoir) and Box Canyon Dam as shown in Figure 1. The Pend Oreille drainage basin is shown in Figure 2. An existing model of the Box Canyon reach was updated from CE-QUALW2 Version 3.0 to Version 3.5. This current research involves improving the calibration of the original model (1997 and 1998) and expanding the model using 2004 as an additional data set for calibration. The use of field data from 2004 as an additional calibration year was chosen to improve the confidence in the model’s predictive ability for temperature. Hence, the model simulations were run from January 1st to December 31st in each of the 3 years of model simulation: 1997, 1998 and 2004. The model chosen for development is CE-QUAL-W2 Version 3.5 (Cole and Wells, 2006). This is a twodimensional unsteady hydrodynamic and water quality model that includes typical eutrophication parameters (algae, nutrients, temperature, organic matter, dissolved oxygen, pH). The PSU-WQRG (Water Quality Research Group) is a center for development of this modeling tool (see http://www.cee.pdx.edu/w2). The model simulation for scenarios was run from January 1st, 2004 to September 25th, 2005. Close

• 8. [Article] Lower Willamette River Model: Model Calibration

  Water Environment Services of Clackamas County is in the process of planning upgrades on several of its wastewater treatment plants (WWTPs) which discharge into the Lower Willamette River. The goals of ...

  Citation × Citation Citation Abstract Copy Title: Lower Willamette River Model: Model Calibration Author: Berger, Chris, Annear, Robert Leslie, Wells, Scott A. Year: 2001 Water Environment Services of Clackamas County is in the process of planning upgrades on several of its wastewater treatment plants (WWTPs) which discharge into the Lower Willamette River. The goals of the modeling effort were to: • Gather data to construct a computer simulation model of the Lower Willamette River system in order to evaluate the impact of the WWTP discharges on water quality • Ensure that the model accurately represents the system physics and chemistry (flow, temperature, dissolved oxygen and nutrient dynamics) by model calibration • Use the model to evaluate how to meet various future discharge scenarios for Water Environment Services of Clackamas County. This report evaluates the model calibration and discusses issues relative to that calibration effort. The calibration effort focused on model predictions of hydrodynamics (flow and water level), temperature, and eutrophication model parameters (such as nutrients, algae, dissolved oxygen, organic matter, coliform). Title: Lower Willamette River Model: Model Calibration Author: Berger, Chris, Annear, Robert Leslie, Wells, Scott A. Year: 2001 Water Environment Services of Clackamas County is in the process of planning upgrades on several of its wastewater treatment plants (WWTPs) which discharge into the Lower Willamette River. The goals of the modeling effort were to: • Gather data to construct a computer simulation model of the Lower Willamette River system in order to evaluate the impact of the WWTP discharges on water quality • Ensure that the model accurately represents the system physics and chemistry (flow, temperature, dissolved oxygen and nutrient dynamics) by model calibration • Use the model to evaluate how to meet various future discharge scenarios for Water Environment Services of Clackamas County. This report evaluates the model calibration and discusses issues relative to that calibration effort. The calibration effort focused on model predictions of hydrodynamics (flow and water level), temperature, and eutrophication model parameters (such as nutrients, algae, dissolved oxygen, organic matter, coliform). Close

• 9. [Article] Pend Oreille River, Box Canyon Model: Model Development and Calibration

  The purpose of this study was to improve the existing Version 3.0 application of CE-QUAL-W2 of the Pend Oreille River between Box Canyon Dam and Albeni Falls Dam by performing the tasks outlined above. ...

  Citation × Citation Citation Abstract Copy Title: Pend Oreille River, Box Canyon Model: Model Development and Calibration Author: Annear, Robert Leslie, Berger, Chris, Wells, Scott A. Year: 2006 The purpose of this study was to improve the existing Version 3.0 application of CE-QUAL-W2 of the Pend Oreille River between Box Canyon Dam and Albeni Falls Dam by performing the tasks outlined above. In addition, the use of field data from 2004 as an additional calibration year would improve the confidence in the model’s predictive ability for temperature. The model simulations were run from January 1st to December 31st in each of the 3 years of model simulation: 1997, 1998 and 2004. The model chosen for development is CE-QUAL-W2 Version 3.5 (Cole and Wells, 2006). This is a twodimensional unsteady hydrodynamic and water quality model that includes typical eutrophication parameters (algae, nutrients, temperature, organic matter, dissolved oxygen, pH). The PSU-WQRG is a center for development of this modeling tool (see http://www.cee.pdx.edu/w2). Title: Pend Oreille River, Box Canyon Model: Model Development and Calibration Author: Annear, Robert Leslie, Berger, Chris, Wells, Scott A. Year: 2006 The purpose of this study was to improve the existing Version 3.0 application of CE-QUAL-W2 of the Pend Oreille River between Box Canyon Dam and Albeni Falls Dam by performing the tasks outlined above. In addition, the use of field data from 2004 as an additional calibration year would improve the confidence in the model’s predictive ability for temperature. The model simulations were run from January 1st to December 31st in each of the 3 years of model simulation: 1997, 1998 and 2004. The model chosen for development is CE-QUAL-W2 Version 3.5 (Cole and Wells, 2006). This is a twodimensional unsteady hydrodynamic and water quality model that includes typical eutrophication parameters (algae, nutrients, temperature, organic matter, dissolved oxygen, pH). The PSU-WQRG is a center for development of this modeling tool (see http://www.cee.pdx.edu/w2). Close

• 10. [Article] Upper Spokane River Model: Model Calibration, 1991 and 2000

  The Washington Department of Ecology is interested in a water quality model for the Upper Spokane River system for use in developing Total Maximum Daily Loads (TMDLs). The goals of this modeling effort ...

  Citation × Citation Citation Abstract Copy Title: Upper Spokane River Model: Model Calibration, 1991 and 2000 Author: Berger, Chris, Annear, Robert Leslie, Wells, Scott A. Year: 2002 The Washington Department of Ecology is interested in a water quality model for the Upper Spokane River system for use in developing Total Maximum Daily Loads (TMDLs). The goals of this modeling effort are to: • Gather data to construct a computer simulation model of the Spokane River system including Long Lake Reservoir and the pools behind Nine Mile dam, Upper Falls dam and Upriver dam. • Ensure that the model accurately represents the system hydrodynamics and water quality (flow, temperature, dissolved oxygen and nutrient dynamics) This report evaluates the model calibration and discusses issues relative to that calibration effort. The calibration effort focused on model predictions of hydrodynamics (flow and water level), temperature, and eutrophication model parameters (such as nutrients, algae, dissolved oxygen, organic matter, coliform). The model calibration periods were from February 1, 1991 to October 31, 1991 and from January 1, 2000 to October 31, 2000. Title: Upper Spokane River Model: Model Calibration, 1991 and 2000 Author: Berger, Chris, Annear, Robert Leslie, Wells, Scott A. Year: 2002 The Washington Department of Ecology is interested in a water quality model for the Upper Spokane River system for use in developing Total Maximum Daily Loads (TMDLs). The goals of this modeling effort are to: • Gather data to construct a computer simulation model of the Spokane River system including Long Lake Reservoir and the pools behind Nine Mile dam, Upper Falls dam and Upriver dam. • Ensure that the model accurately represents the system hydrodynamics and water quality (flow, temperature, dissolved oxygen and nutrient dynamics) This report evaluates the model calibration and discusses issues relative to that calibration effort. The calibration effort focused on model predictions of hydrodynamics (flow and water level), temperature, and eutrophication model parameters (such as nutrients, algae, dissolved oxygen, organic matter, coliform). The model calibration periods were from February 1, 1991 to October 31, 1991 and from January 1, 2000 to October 31, 2000. Close