Search

Search Results

• 1. [Article] A Comparison of Five Models for Estimating Clear-Sky Solar Radiation

  Many agencies in the USA are developing management approaches to address water quality concerns and threatened and endangered species habitat requirements in water bodies. Many of these water bodies are ...

  Citation × Citation Citation Abstract Copy Title: A Comparison of Five Models for Estimating Clear-Sky Solar Radiation Author: Annear, Robert Leslie, Wells, Scott A. Year: 2007 Many agencies in the USA are developing management approaches to address water quality concerns and threatened and endangered species habitat requirements in water bodies. Many of these water bodies are water quality limited for temperature. Factors influencing stream temperature include: streamside vegetation, topographic shading, inflows and outflows, stream width, stream depth, light extinction and solar radiation. One of the key driving factors in estimating a water body heat budget is calculating the amount of solar radiation incident on the water surface. Even though it is preferable to measure clear-sky solar radiation, many temperature models rely on theoretical estimates of clear-sky solar radiation. The literature on estimating short-wave solar radiation by calculating the position of the sun and attenuating the radiation through the atmosphere was reviewed. As a first step in relating water temperature to solar radiation, several empirical solar radiation models were calibrated to data at seventeen sites around the United States for clear-sky days. Sensitivity analyses were conducted and differences between the models were examined. Results indicated that the more complex models for calculating solar radiation resulted in better estimates of clear-sky solar radiation once they were calibrated to data. When no data were available, models with one or no calibration parameters did reasonably well at estimating clear-sky solar radiation. Title: A Comparison of Five Models for Estimating Clear-Sky Solar Radiation Author: Annear, Robert Leslie, Wells, Scott A. Year: 2007 Many agencies in the USA are developing management approaches to address water quality concerns and threatened and endangered species habitat requirements in water bodies. Many of these water bodies are water quality limited for temperature. Factors influencing stream temperature include: streamside vegetation, topographic shading, inflows and outflows, stream width, stream depth, light extinction and solar radiation. One of the key driving factors in estimating a water body heat budget is calculating the amount of solar radiation incident on the water surface. Even though it is preferable to measure clear-sky solar radiation, many temperature models rely on theoretical estimates of clear-sky solar radiation. The literature on estimating short-wave solar radiation by calculating the position of the sun and attenuating the radiation through the atmosphere was reviewed. As a first step in relating water temperature to solar radiation, several empirical solar radiation models were calibrated to data at seventeen sites around the United States for clear-sky days. Sensitivity analyses were conducted and differences between the models were examined. Results indicated that the more complex models for calculating solar radiation resulted in better estimates of clear-sky solar radiation once they were calibrated to data. When no data were available, models with one or no calibration parameters did reasonably well at estimating clear-sky solar radiation. Close

• 2. [Article] Willamette River Basin Temperature TMDL Model: Model Calibration

  The State of Oregon Department of Environmental Quality (DEQ) is developing a TMDL for temperature in the Willamette River basin shown in Figure 1. The study area included the Willamette River and all ...

  Citation × Citation Citation Abstract Copy Title: Willamette River Basin Temperature TMDL Model: Model Calibration Author: Berger, Chris, McKillip, Michael Lee, Annear, Robert Leslie, Khan, Sher Jamal, Wells, Scott A. Year: 2004 The State of Oregon Department of Environmental Quality (DEQ) is developing a TMDL for temperature in the Willamette River basin shown in Figure 1. The study area included the Willamette River and all major tributaries (except the Tualatin River where a TMDL process was already concluded). A large section of the Columbia River was also modeled to provide adequate boundary representation of tidal flows in the lower Willamette River. The Willamette River below the Oregon City Falls in the Portland metropolitan area has a typical diurnal tidal range of 1 m. The development of a dynamic model of temperature and hydrodynamics of the entire river basin incorporating shading were primary requirements of this modeling study. The model would be used by DEQ to set temperature limits on point source dischargers and to evaluate the impact of management strategies on river temperatures to improve fish habitat. Some of these strategies included modifications of the dam at the Willamette River Falls south of Portland and channel reconfigurations. The river basin model was originally divided into several reaches. Individual models were developed for each reach. The models were set-up for each section of the Willamette basin as described in Annear et al. (2004a), the models were calibrated to field data and management strategies were evaluated as described in Annear et al (2004b). This report outlines the model calibration of each of these model sections or elements for both the calibration time periods. The calibration period for each model section differs due to the availability of boundary condition data. The model management simulation scenarios (Annear et al, 2004b) also required boundary condition data that extended past the calibration periods. Title: Willamette River Basin Temperature TMDL Model: Model Calibration Author: Berger, Chris, McKillip, Michael Lee, Annear, Robert Leslie, Khan, Sher Jamal, Wells, Scott A. Year: 2004 The State of Oregon Department of Environmental Quality (DEQ) is developing a TMDL for temperature in the Willamette River basin shown in Figure 1. The study area included the Willamette River and all major tributaries (except the Tualatin River where a TMDL process was already concluded). A large section of the Columbia River was also modeled to provide adequate boundary representation of tidal flows in the lower Willamette River. The Willamette River below the Oregon City Falls in the Portland metropolitan area has a typical diurnal tidal range of 1 m. The development of a dynamic model of temperature and hydrodynamics of the entire river basin incorporating shading were primary requirements of this modeling study. The model would be used by DEQ to set temperature limits on point source dischargers and to evaluate the impact of management strategies on river temperatures to improve fish habitat. Some of these strategies included modifications of the dam at the Willamette River Falls south of Portland and channel reconfigurations. The river basin model was originally divided into several reaches. Individual models were developed for each reach. The models were set-up for each section of the Willamette basin as described in Annear et al. (2004a), the models were calibrated to field data and management strategies were evaluated as described in Annear et al (2004b). This report outlines the model calibration of each of these model sections or elements for both the calibration time periods. The calibration period for each model section differs due to the availability of boundary condition data. The model management simulation scenarios (Annear et al, 2004b) also required boundary condition data that extended past the calibration periods. Close

• 3. [Article] Willamette River Basin Temperature TMDL Model: Model Scenarios

  The State of Oregon Department of Environmental Quality (DEQ) is developing a TMDL for temperature in the Willamette River basin shown in Figure 1. The study area included the Willamette River and all ...

  Citation × Citation Citation Abstract Copy Title: Willamette River Basin Temperature TMDL Model: Model Scenarios Author: Annear, Robert Leslie, McKillip, Michael Lee, Khan, Sher Jamal, Berger, Chris, Wells, Scott A. Year: 2004 The State of Oregon Department of Environmental Quality (DEQ) is developing a TMDL for temperature in the Willamette River basin shown in Figure 1. The study area included the Willamette River and all major tributaries (except the Tualatin River where a TMDL process was already concluded). A large section of the Columbia River was also modeled to provide adequate boundary representation of tidal flows in the lower Willamette River. The Willamette River below the Oregon City Falls in the Portland metropolitan area has a typical diurnal tidal range of 1 m. The development of a dynamic model of temperature and hydrodynamics of the entire river basin incorporating shading were primary requirements of this modeling study. The model would be used by DEQ to set temperature limits on point source dischargers and to evaluate the impact of management strategies on river temperatures to improve fish habitat. Some of these strategies included modifications of the dam at the Willamette River Falls south of Portland and channel reconfigurations. Once the models were set-up for each section of the Willamette basin, the model was calibrated to field data and management strategies were evaluated. These are the subjects of two other reports: Annear et al. (2004) and Berger et al. (2004). This report outlines the results of implementing model scenarios for each of the model sections or elements for specific time periods. The model scenario simulation periods used to investigate management scenarios required boundary condition data that extended past the model calibration periods. The model simulation period for year 2001 was from June 1 to October 31 and for year 2002 from April 1 to October 31. Title: Willamette River Basin Temperature TMDL Model: Model Scenarios Author: Annear, Robert Leslie, McKillip, Michael Lee, Khan, Sher Jamal, Berger, Chris, Wells, Scott A. Year: 2004 The State of Oregon Department of Environmental Quality (DEQ) is developing a TMDL for temperature in the Willamette River basin shown in Figure 1. The study area included the Willamette River and all major tributaries (except the Tualatin River where a TMDL process was already concluded). A large section of the Columbia River was also modeled to provide adequate boundary representation of tidal flows in the lower Willamette River. The Willamette River below the Oregon City Falls in the Portland metropolitan area has a typical diurnal tidal range of 1 m. The development of a dynamic model of temperature and hydrodynamics of the entire river basin incorporating shading were primary requirements of this modeling study. The model would be used by DEQ to set temperature limits on point source dischargers and to evaluate the impact of management strategies on river temperatures to improve fish habitat. Some of these strategies included modifications of the dam at the Willamette River Falls south of Portland and channel reconfigurations. Once the models were set-up for each section of the Willamette basin, the model was calibrated to field data and management strategies were evaluated. These are the subjects of two other reports: Annear et al. (2004) and Berger et al. (2004). This report outlines the results of implementing model scenarios for each of the model sections or elements for specific time periods. The model scenario simulation periods used to investigate management scenarios required boundary condition data that extended past the model calibration periods. The model simulation period for year 2001 was from June 1 to October 31 and for year 2002 from April 1 to October 31. Close

• 4. [Article] Willamette River Basin Temperature TMDL Model: Boundary Conditions and Model Setup

  The State of Oregon Department of Environmental Quality (DEQ) is developing a TMDL for temperature in the Willamette River basin shown in Figure 1. The study area included the Willamette River and all ...

  Citation × Citation Citation Abstract Copy Title: Willamette River Basin Temperature TMDL Model: Boundary Conditions and Model Setup Author: Annear, Robert Leslie, McKillip, Michael Lee, Khan, Sher Jamal, Berger, Chris, Wells, Scott A. Year: 2004 The State of Oregon Department of Environmental Quality (DEQ) is developing a TMDL for temperature in the Willamette River basin shown in Figure 1. The study area included the Willamette River and all major tributaries (except the Tualatin River where a TMDL process was already concluded). A large section of the Columbia River was also modeled to provide adequate boundary representation of tidal flows in the lower Willamette River. The Willamette River below the Oregon City Falls in the Portland metropolitan area has a typical diurnal tidal range of 1 m. The development of a dynamic model of temperature and hydrodynamics of the entire river basin incorporating shading were primary requirements of this modeling study. The model would be used by DEQ to set temperature limits on point source dischargers and to evaluate the impact of management strategies on river temperatures to improve fish habitat. Some of these strategies included modifications of the dam at the Willamette River Falls south of Portland and channel reconfigurations. Once the models were set-up for each section of the Willamette basin, the model was calibrated to field data and management strategies were evaluated. These are the subjects of two other reports: Annear et al. (2004b) and Berger et al. (2004). This report outlines the model development of each of these model sections or elements for both the calibration time periods and the management scenario time periods. The calibration period for each model section differs due to the availability of boundary condition data. The model simulation periods used to investigate management scenarios (Annear et al, 2004b) also required boundary condition data that extended past the calibration periods. Title: Willamette River Basin Temperature TMDL Model: Boundary Conditions and Model Setup Author: Annear, Robert Leslie, McKillip, Michael Lee, Khan, Sher Jamal, Berger, Chris, Wells, Scott A. Year: 2004 The State of Oregon Department of Environmental Quality (DEQ) is developing a TMDL for temperature in the Willamette River basin shown in Figure 1. The study area included the Willamette River and all major tributaries (except the Tualatin River where a TMDL process was already concluded). A large section of the Columbia River was also modeled to provide adequate boundary representation of tidal flows in the lower Willamette River. The Willamette River below the Oregon City Falls in the Portland metropolitan area has a typical diurnal tidal range of 1 m. The development of a dynamic model of temperature and hydrodynamics of the entire river basin incorporating shading were primary requirements of this modeling study. The model would be used by DEQ to set temperature limits on point source dischargers and to evaluate the impact of management strategies on river temperatures to improve fish habitat. Some of these strategies included modifications of the dam at the Willamette River Falls south of Portland and channel reconfigurations. Once the models were set-up for each section of the Willamette basin, the model was calibrated to field data and management strategies were evaluated. These are the subjects of two other reports: Annear et al. (2004b) and Berger et al. (2004). This report outlines the model development of each of these model sections or elements for both the calibration time periods and the management scenario time periods. The calibration period for each model section differs due to the availability of boundary condition data. The model simulation periods used to investigate management scenarios (Annear et al, 2004b) also required boundary condition data that extended past the calibration periods. Close

• 5. [Article] Green River CE-QUAL-W2 Project: A Hydrodynamic and Water Quality Study of the Green River King County, Washington

  This report describes the data processing and model calibration performed for a hydrodynamic and water quality model of the Green River, located in King County, Washington. Figure 1 shows the location ...

  Citation × Citation Citation Abstract Copy Title: Green River CE-QUAL-W2 Project: A Hydrodynamic and Water Quality Study of the Green River King County, Washington Author: Kraft, Tim, Annear, Robert Leslie, Berger, Chris, Wells, Scott A. Year: 2004 This report describes the data processing and model calibration performed for a hydrodynamic and water quality model of the Green River, located in King County, Washington. Figure 1 shows the location of the river, and the limits of the section of river that was modeled. The Green River flows from its headwaters in the Cascade Mountain foothills through the King County, Washington communities of Auburn, Kent, and Tukwila before discharging into the Duwamish River. Two sections of the river were modeled in this project. The Middle Green River begins in the Cascade Mountain foothills east of Tacoma, and continues downstream to the city of Auburn, WA. The Lower Green River continues from Auburn to the confluence with the Duwamish River, in the town of Tukwila. The Green/Duwamish River system is unique in that it flows through a heavily urbanized and industrialized environment yet supports a large salmon population (Green/Duwamish Ecosystem Restoration Study, 2003). To protect the river and its prime salmon habitat, King County and the US Army Corps of Engineers have joined together on a study to identify and implement strategies for restoring and protecting the Green/Duwamish River System and its tributaries (Green/Duwamish Ecosystem Restoration Study, 2003). As part of the Green-Duwamish Watershed Water Quality Assessment Program, King County contracted with Portland State University to develop a hydrodynamic and water quality model for the Lower and Middle Green River. This model will be used in Total Maximum Daily Load (TMDL) development, in assessing current water quality conditions in the river, and as a planning tool for evaluating the impacts of future development in the basin. Title: Green River CE-QUAL-W2 Project: A Hydrodynamic and Water Quality Study of the Green River King County, Washington Author: Kraft, Tim, Annear, Robert Leslie, Berger, Chris, Wells, Scott A. Year: 2004 This report describes the data processing and model calibration performed for a hydrodynamic and water quality model of the Green River, located in King County, Washington. Figure 1 shows the location of the river, and the limits of the section of river that was modeled. The Green River flows from its headwaters in the Cascade Mountain foothills through the King County, Washington communities of Auburn, Kent, and Tukwila before discharging into the Duwamish River. Two sections of the river were modeled in this project. The Middle Green River begins in the Cascade Mountain foothills east of Tacoma, and continues downstream to the city of Auburn, WA. The Lower Green River continues from Auburn to the confluence with the Duwamish River, in the town of Tukwila. The Green/Duwamish River system is unique in that it flows through a heavily urbanized and industrialized environment yet supports a large salmon population (Green/Duwamish Ecosystem Restoration Study, 2003). To protect the river and its prime salmon habitat, King County and the US Army Corps of Engineers have joined together on a study to identify and implement strategies for restoring and protecting the Green/Duwamish River System and its tributaries (Green/Duwamish Ecosystem Restoration Study, 2003). As part of the Green-Duwamish Watershed Water Quality Assessment Program, King County contracted with Portland State University to develop a hydrodynamic and water quality model for the Lower and Middle Green River. This model will be used in Total Maximum Daily Load (TMDL) development, in assessing current water quality conditions in the river, and as a planning tool for evaluating the impacts of future development in the basin. Close